ZB2L3 18650 Battery Capacity Tester External Load Discharge Type 1.2-12V Tester with 2 7.5 Resistors
$15.30
Type With 2*5W+1*50W Resistor / Type With 1*50W Resistor / Type With 2*5W Resistor /
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specification
Power supply voltage:DC4.5-6V (micro USB interface)
Working current:no more than 70mA
Discharge voltage:1.00V-15.00V resolution 0.01V
Termination voltage range:0.5-11.0V
Support current through:maximum 3.000A resolution 0.001A
Maximum voltage measurement error:1% + 0.02V
Maximum current measurement error:1.2%+-0.002A
The highest battery capacity range:9999Ah (1Ah=1000mAh). The larger value is switched by the decimal point shift. When it is lower than 10Ah, it is displayed as X.XXX, and when it is above 10Ah, it is displayed as XX.XX, and so on.
Board size:50mmX37mm
Finished product size:50mmX37mmX17mm (length X width X height maximum position size, including copper foot height)
Board and accessories weight:single board 28g (including copper column), two 5W ceramic resistor 9g, 50W resistance about 27g (including line)
Note
In order to improve the voltage measurement accuracy, this circuit specially designed the DC offset. When the terminal is not connected, it will display a small voltage, which does not affect the actual measurement. If you short-circuit the input terminal (absolute 0V), it will display 0. . If you want to understand the principle, you can check the superposition theorem in electrical engineering.
During the use of resistance discharge, the resistance load will be severely heated, please pay attention to safety! 50W aluminum shell resistor (has been welded a high temperature wire), please install it on the metal plate!
Instructions
1. The battery under test should be fully charged first.
2. Connect the positive pole of the battery under test to the positive input, the negative pole to the input negative pole, and the reverse polarity (the reverse connection with the load may damage the circuit)! Connect the load to the output positive and output negative, and give the tester micro USB working power (not available for desktop or notebook USB), and the battery voltage is displayed.
3. To start the test directly, just press the “OK Inch button, the tester can automatically set the appropriate termination voltage according to the battery full charge voltage, and will flash the display 3 times to start the test. Need to manually set the termination voltage only need to press the inch+inch or inch-inch button to modify the battery voltage display state, the termination voltage display is P beginning, the latter represents the voltage value, the resolution is 0.1V, after setting, press inchOKinch inchstart testing.
4. After the test starts, the tester will turn on the electronic switch that controls the load. The test process data display will be displayed between the discharge capacity (Ah), the current discharge current (A) and the battery voltage (V). When the battery voltage reaches the set termination voltage, the tester cuts off the load control switch, and the display data stays on the capacity (Ah) and flashes rapidly with the corresponding indicator light. The capacity displayed at this time is the actual discharge capacity of the battery. “OK Inch can terminate the flashing to make the data display stably. Press the “OK Inch button again to return to the power-on state and replace the battery test.
Error code and meaning
Err1:Battery voltage is higher than 15V
Err2:Battery voltage is lower than the set termination voltage
Err3:The battery cannot withstand the load discharge current or the line internal resistance is too large
Err4:The current is too large (current exceeds 3.1A)
Err5:Improper use or wiring error has caused the device to burn out and cannot be used (current sampling or control switch MOS burned)
Secondary calibration operation (after self-running calibration, it means to give up the warranty)
Press and hold the three buttons at the same time to power on the tester, enter the calibration mode, first display the number of calibration records and then enter the official calibration sampling program display 0u0A, then short-circuit the input positive and negative, then press the inchOKinch button to complete the display J10u, Apply 10.00V standard DC voltage between the input positive and negative poles, then press the “OK Inch button, then display J2.0A, apply 2.0A constant DC current to the output negative pole (inflow direction) and input negative pole (outflow direction) and press Move the “OK Inch button to complete the calibration. The tester pre-audits the calibration data. If the calibration data is reliable, it will display 4 calibration numbers and then exit. If the pre-audit considers the data to be unreliable, the data will be discarded.
Package includes
1 x Tester
1/2/3 x Resistor (optional)
Weight | 0.08 kg |
---|
Customers Also Viewed
5pcs ST-LINK V2 Programmer Emulator Mini STLINK Downloader for STM8 / STM32 MCU Development Board
$45.35Test & Measuring ModuleAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.Description– Only U disk size and compatible with official ST-LINK V2.– Support official firmware upgrade, support all series of STM8 (SWIM interface), STM32(SWD interface).– Two-channel power output 5V / 3.3V and easier …
5pcs Breadboard Power Supply Module Circuit Test 3.3V 5V Switchable
$24.83Power Supply ModuleAdd to cartDescriptionThe size is exactly the same as most bread plates.Small size, suitable for all kinds of experimental equipment.It has the function of current limiting protection.The interface is popular, and the switching voltage can be switched.Input voltage:5VOutput voltage:5V/3.3V switchableOutput current:less than 500mASize:53 x 11mmPackage Included5 x Power Supply Module
3pcs Audio Speaker Protection Board Amplifier Components DC Protect Kit DIY
$24.37DIY Electronic KitsAdd to cartSpecificationInput voltage:AC12-15 VSize(L*W*H):6x 4 x 2.5 cm (Finished)FeatureWith power on delay (about 3 seconds) and DC protection (control voltage around 1 V)With LED status display, when the protection light, the normal work time offUsing 15 A large current relayWorking voltage aAC 12 to 15 V, need independent power supply.Package includes3 x Double-sided circuit boards 3 …
3pcs Audio Speaker Protection Board Amplifier Components DC Protect Kit DIYRead More
5Pcs AMS1117 3.3V Power Supply Module with DC Socket And Switch
$9.02Power Supply ModuleAdd to cartDescription1. onboard AMS1117-3.3 chip2. onboard DC input voltage range of 4.75 V to 12 V3. the onboard 7 * 7 self-locking switch, convenient to control power supply turned on and off during the test4. the onboard power light, indicating whether the power supply5. 4-way output voltage interface, convenient connection during the test6. The board size:48.5 …
5Pcs AMS1117 3.3V Power Supply Module with DC Socket And SwitchRead More
32Pcs Science Chemical Experiment Demonstration Tools Reagent Alcohol Lamp Full Set Storage Box
$89.79Lab Clamp & StandAdd to cartSpecificationType:Chemical Experiment BoxMaterial:Plastic, GlassFeatures1. High quality materials. Environmentally friendly and durable.2. Deepen understanding:thinking at your own hands can give your child a deeper understanding of knowledge.3. The variety of experimental tools is rich, which can meet different experimental needsPackage IncludedItem:QuantityBlue and Red Cup:2 SetFour Treasure Box:1 PcsAlcohol Lamp:2 PcsDropping Bottle:2 PcsSpray Bottle:1 PcsBule Dropping Bottle:3 …
3Pcs T2310 AC110V 220V Programmable Digital Time Delay Switch Relay T2310 Normally Open Timer Control Module 0-999S/Min/Hour
$32.79Test & Measuring ModuleAdd to cartFeatureIndependent crystal oscillator, more accurate timing1. Convenient direct output wiring2. Add buzzer and audible alarm3. Add pause button to stop urgently5. Start and stop setting mode, provincial conversion, which is more convenient6. Automatically save when power off, run automatically when power on7. Timing units can be set separately, with 36 working combinations8. Timing range:0-999 seconds, …
5pcs 30CM 1M Portable Photosensitive Dry Film for Circuit Photoresist Sheet for Plating Hole Covering Etching for Producing PCB Board
$21.78Electronic Accessories & SuppliesAdd to cartFeaturesUniversal used in producing PCB board, attach on the PCB surface to make it photosensitive.Suitable for electroplating, hole covering and etching.Great hole covering ability.High resolution.Great adaptive capacity to different material.Durable in pH 8.0-8.5 situation.1.5mil dry film fully covers a 0.25inch height hole.Suitable for usual plating bath, no wrinkle or color error.SpecificationWidth:approx. 30 cm/11.81inchLength:approx. 100 cm/39.37inchOperating …
Reviews
There are no reviews yet.