ZB2L3 18650 Battery Capacity Tester External Load Discharge Type 1.2-12V Tester with 2 7.5 Resistors
$15.30
Type With 2*5W+1*50W Resistor / Type With 1*50W Resistor / Type With 2*5W Resistor /
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specification
Power supply voltage:DC4.5-6V (micro USB interface)
Working current:no more than 70mA
Discharge voltage:1.00V-15.00V resolution 0.01V
Termination voltage range:0.5-11.0V
Support current through:maximum 3.000A resolution 0.001A
Maximum voltage measurement error:1% + 0.02V
Maximum current measurement error:1.2%+-0.002A
The highest battery capacity range:9999Ah (1Ah=1000mAh). The larger value is switched by the decimal point shift. When it is lower than 10Ah, it is displayed as X.XXX, and when it is above 10Ah, it is displayed as XX.XX, and so on.
Board size:50mmX37mm
Finished product size:50mmX37mmX17mm (length X width X height maximum position size, including copper foot height)
Board and accessories weight:single board 28g (including copper column), two 5W ceramic resistor 9g, 50W resistance about 27g (including line)
Note
In order to improve the voltage measurement accuracy, this circuit specially designed the DC offset. When the terminal is not connected, it will display a small voltage, which does not affect the actual measurement. If you short-circuit the input terminal (absolute 0V), it will display 0. . If you want to understand the principle, you can check the superposition theorem in electrical engineering.
During the use of resistance discharge, the resistance load will be severely heated, please pay attention to safety! 50W aluminum shell resistor (has been welded a high temperature wire), please install it on the metal plate!
Instructions
1. The battery under test should be fully charged first.
2. Connect the positive pole of the battery under test to the positive input, the negative pole to the input negative pole, and the reverse polarity (the reverse connection with the load may damage the circuit)! Connect the load to the output positive and output negative, and give the tester micro USB working power (not available for desktop or notebook USB), and the battery voltage is displayed.
3. To start the test directly, just press the “OK Inch button, the tester can automatically set the appropriate termination voltage according to the battery full charge voltage, and will flash the display 3 times to start the test. Need to manually set the termination voltage only need to press the inch+inch or inch-inch button to modify the battery voltage display state, the termination voltage display is P beginning, the latter represents the voltage value, the resolution is 0.1V, after setting, press inchOKinch inchstart testing.
4. After the test starts, the tester will turn on the electronic switch that controls the load. The test process data display will be displayed between the discharge capacity (Ah), the current discharge current (A) and the battery voltage (V). When the battery voltage reaches the set termination voltage, the tester cuts off the load control switch, and the display data stays on the capacity (Ah) and flashes rapidly with the corresponding indicator light. The capacity displayed at this time is the actual discharge capacity of the battery. “OK Inch can terminate the flashing to make the data display stably. Press the “OK Inch button again to return to the power-on state and replace the battery test.
Error code and meaning
Err1:Battery voltage is higher than 15V
Err2:Battery voltage is lower than the set termination voltage
Err3:The battery cannot withstand the load discharge current or the line internal resistance is too large
Err4:The current is too large (current exceeds 3.1A)
Err5:Improper use or wiring error has caused the device to burn out and cannot be used (current sampling or control switch MOS burned)
Secondary calibration operation (after self-running calibration, it means to give up the warranty)
Press and hold the three buttons at the same time to power on the tester, enter the calibration mode, first display the number of calibration records and then enter the official calibration sampling program display 0u0A, then short-circuit the input positive and negative, then press the inchOKinch button to complete the display J10u, Apply 10.00V standard DC voltage between the input positive and negative poles, then press the “OK Inch button, then display J2.0A, apply 2.0A constant DC current to the output negative pole (inflow direction) and input negative pole (outflow direction) and press Move the “OK Inch button to complete the calibration. The tester pre-audits the calibration data. If the calibration data is reliable, it will display 4 calibration numbers and then exit. If the pre-audit considers the data to be unreliable, the data will be discarded.
Package includes
1 x Tester
1/2/3 x Resistor (optional)
Weight | 0.08 kg |
---|
Customers Also Viewed
EraClean Smart Control Ultrasonic Cleaner 45000Hz High Frequency Vibration Jewelry Eyeglasses Cleaner 360 Cleaning Machine From You Pin
$80.99Laboratory Heating EquipmentsAdd to cartDear Customer,Thank you for supporting, the orders will be shipped before 10st Nov.Hope your kindly understanding and support. Thank you:)Description[New Release] EraClean Mini Ultrasonic Cleaner from XIAOMI ECO Brand System, Quality Guaranteed, With Mute Quiet Design, Cleaning Anything You Want in 3 Minutes.Smart Control Ultrasonic Cleaner 45000Hz High Frequency Vibration Jewelry Eyeglasses Cleaner 360° Thoroughly …
DIY 12V 420W 6-Chip Semiconductor Refrigeration Cooling Device thermoelectric Cooler Air Conditioning High Cooling Efficiency
$129.99Electronic Accessories & SuppliesAdd to cartDescriptionName:420W 6-Chip Semiconductor Air-Conditioning DIY Radiator KitMaterial:metalSize:160*60*60mmVoltage:12VPower:420W( 6-Chip) In the case of 15.4VElectric current:36ASteady current:27ARed line:inch+inch , Black line:inch-inchRefrigeration effect depends on the size of the cooling space, ambient temperature, heat insulation, sealability ,etc…UseSmall space cooling, learning the principle of semiconductor refrigeration, the company developed cooling equipment research, pet air-conditioning, etc., use to cool down …
Lampow LP-9027 DC 12V 24V Waterproof Mirror Touch Sensor Control Switch for LED Strip Light
$15.30Electronic Accessories & SuppliesAdd to cartDescriptionType:LP-9027Output Mode:Sensor output, input is outputSwitch mode:touch sensor on/off switchInstallation:recessed installationWaterproofLightweight and compact sizeEasy to install, stable, long lifeApplication:LED light, LED strip, cabinet kitchen light, kinds of electric applicationsSpecificationsMaterial:Plastic+MetalColor:WhiteVoltage:12-24VOutput Current:3AQuiescent CurrentService time:> 80000hWorking Temperature:-20-50°Hole Diameter:17mmCable Length:0.5m(Output) 1.5m(Input)Size:19*11mmPackage included1 x Touch Sensor Control Switch
M5StickC ESP32 PICO Color LCD Mini IoT Development Board Finger Computer + Expansion Board Prototyping for M5StickC ESP32 Mini IoT Development Board Finger Computer
$42.47Motherboard & Development BoardAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.This is without watch accessories,If you like with watch accessories>>>with watch accessories:Click here to BUY>>>More M5Stack Item:Click here to openDescriptionM5Stick is a mini M5Stack, powered by ESP32. It is a portable, easy-to-use, …
PAJ7620U2 Gesture Recognition Sensor Module DIY IIC 9 Gesture Recognition Controller Board
$16.71Sensor & Detector ModuleAdd to cart>>>Manual:Click here to open Overview 1. This is a gesture recognition sensor based on PAJ7620U2. It can recognize 9 different gestures including up, down, left, right, front, back, clockwise, counterclockwise, and swing. 2. The gesture recognition module uses the I2C interface and it use the corresponding library function to program and control. The signal returned …
PAJ7620U2 Gesture Recognition Sensor Module DIY IIC 9 Gesture Recognition Controller BoardRead More
5Pcs Magnetic Field Antenna Large EMC EMI Near Field Probe Conduction
$39.35RF amplifierAdd to cartFeature1. Magnetic field extra large probeInterface:SMA outer screw inner holeProduct size:110*45.5MMProduct weight 8 grams2. Magnetic field large probeInterface:SMA outer screw inner holeProduct size:110*30MMProduct weight 8 grams3. Magnetic field medium probeInterface:SMA outer screw inner holeProduct size:110*20MMProduct weight 6 grams4. Small magnetic field probeInterface:SMA outer screw inner holeProduct size:110*12.5MMProduct weight 6 grams5. Electric field probeInterface:SMA outer screw …
5Pcs Magnetic Field Antenna Large EMC EMI Near Field Probe ConductionRead More
Reviews
There are no reviews yet.