DC 12V-36V 15A 500W Brushless Motor Controller BLDC Driver Board Stall Over-current Protection
$30.60
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specification
Operating voltage:DC 12V-36V
Operating Current
Driver Power
Speed Voltage:0.1V-5V
Operating Temperature:-40~85°C
Humidity:90%RH
Stall protection:Yes
Enable Control:Yes
Over-current protection:Yes
Steering control:Yes
Speed control signal:Yes
Size:63 x 42 x 17mm (L x W x H); Probe size 3mm, length:fixing hole center distance 57mm; width:fixed hole center distance 36.5mm
Power terminal Out
VCC(positive power supply)
GND(negative one)
MC(motor phases W)
MB(motor phases V)
MA(motor phase U)
Set for the control side
GND:control terminal ground
VR:the governor end 0-5V(corresponding to 10% of motor speed -100%)
ZF:reversing control(connected to 5V or ground can charge the motor rotation direction)
M:tachometer pulse output(depending on the number of motor poles corresponding to the number of pulse per revolution of the output number)
EL:enable control terminal(connected to 5V ot ground running then 5V, grounding the motor stops)
5V:5V control terminal
Wiring
Control terminal for SET
1. The motor speed control wiring methods:available potentiometer system speed can also be connected to the MCU control, when the potentiometer control wiring, the potentiometer middle pin is connected to VR speed port, potentiometer connected to both ends of 5V and GND terminal voltage more high speed faster.
2. Motor steering control wiring methods:you can switch control can also be connected to the MCU control, to GND in one direction, then in one direction 5V.
3. Pulse speed signal:high and low output . IC can not understand the information with the customer request.
Note
Motor driver board 12-36V DC power input, VCC positive power supply,GND power supply is negative.
Electrical wiring methods:Brushless DC motor for the three lines, corresponding MA/U, MB/V, MC/W
Tips
If you use less than 60W, without additional heat sink , be sure to add more than 60W
heatsink fins drive efficiency without lowering the temperature is too high will shine into permanent damage! The size of the heat sink may be a bad environment based work(recommended cooling surface area greater than 200 square centimeters)!When installing the heat sink ,must pay attention to the back of the module 6 MOS pipe insulation, no insulation, it will be adhered to drive plate permanently damaged! Proposes to add insulation films, both sides of the insulating sheet plus thermal grease!
Package Includes
1 x 12-36V 500W Brushless Motor Controler
Weight | 0.027 kg |
---|
Customers Also Viewed
5PCS Cake Stand Set for Wedding Decorations White Table Kit Decorating Party Suppliers for Fondant Dessert Metal Cupcake Stand
$159.44Lab Clamp & StandAdd to cart5Pcs Metal Cupcake Stand Cake Dessert Wedding Event Party Display Tower Plate Features※ Ideal cake stand, widely used for personal birthday party, birthday, celebrations, banquets, marriage, graduation ceremony. ※ Used to display merchandise, play a very good decorative effect.※ This is also perfect for afternoon tea session. ※ High quality raw iron material, rejecting waste …
Robotdyn Digital Tilt Sensor Module Tilt Switch Angle
$8.73Sensor & Detector ModuleAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.FeatureDigital tilt sensor, have simple function, if the sensor are not placed on a strict flat surface, the little steel ball in the green tube will slip to one end of it, …
Robotdyn Digital Tilt Sensor Module Tilt Switch AngleRead More
20pcs LM317 DC-DC 1.5A 1.2-37V Adjustable Power Supply Board DC Converter Buck Step Down Module
$41.11Boost & Buck ModuleAdd to cartSpecificationsOutput Current:1.5A (minimum), 2.2A (typical value)Input-output voltage difference (VI-VO):40Vdc (max)Adjustable output voltage range:1.2 – 37VWorking temperature:-55 ° C to + 150 ° CCurrent output:1.5AVoltage Input:4.2 – 40 VOperating temperature:0 ° C – 125 ° CCharacteristic frequency:100 (MHz)Module size:35.6 (mm) x 16.8 (mm)Output mode:VOUT output positive, GND output negativePackage included20 x LM317 DC-DC 1.5A 1.2-37V adjustable …
4-way Switch Module Ewelink Phone Remote Control Small Voice DIY SCM Development Modified Board
$13.11Sensor & Detector ModuleAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.Power supply descriptionThis module uses 5V DC power supply, usable with USB power supply equipment such as mobile phone charger, charging treasure, computer and so on.Enter descriptionIt can be connected with four …
MPR121-Breakout-v12 Proximity Capacitive Touch Sensor Controller Keyboard Development Board
$8.73Sensor & Detector ModuleAdd to cartDescriptionThis is a breakout board for Freescale’s MPR121QR2. The MPR121 is a capacitive touch sensor controller driven by an I2C interface.The chip can control up to twelve individual electrodes, as well as a simulated thirteenth electrode. The MPR121 also features eight LED driving pins. When these pins are not configured as electrodes, they may be …
MPR121-Breakout-v12 Proximity Capacitive Touch Sensor Controller Keyboard Development BoardRead More
DG7512 75V 12A High Current Ideal Diode Solar Energy Anti-backflow Charging Anti-backflow Protection Low Resistance
$7.64Electronic Accessories & SuppliesAdd to cartSpecificationModule name:DG7512 anti-backflow ideal diodeWorking voltage:DC5-75VWorking current:12A (MAX) (without heat dissipation for a long time working within 10A,Can be used in parallel to increase operating current)Static operating current:0.7mAInput reverse connection protection:None (do not reverse the positive and negative poles, otherwise the chip will be burned)Working temperature:-40→~125→Connection method:welding outputModule size:25 *14*3.8mmPackage included1 x High Current Ideal …
HBV-1610 2MP Auto Focus Micro Mini USB2.0 Camera Module with Flash Light
$28.42Other Module BoardAdd to cartSpecificationsModel No.:HBV-1610Model Size:86.11mm ≠ 21mm ≠ 5.03mm÷0.2MMTemperature (Operation):-30C to 70CTemperature (Stable Image):0C to 50CAssembly technique:SMT (ROSH)Focus:AutoObject distance:30CM-infinityResolution:600LW/PH (Center)PCB printing ink:Blackinterface:USB 2.0Power supply:USB bus powersupply voltage:DC 5V÷5%Maximum Power consumption:730 mWOperating system request:Win XP/win 7,8 / vista /android 4.0/ mac /Linuxwith uvc Sensor:GT2005 (1/5” )Seneor Package:CSP,Bare DieMaximum resolution:1600*1200Sensitivity:33000mv /(lux-sec)Pixel Size:1.75m x 1.75┢m Maximum Image Transfer Rate:MJPEG 640×480 …
HBV-1610 2MP Auto Focus Micro Mini USB2.0 Camera Module with Flash LightRead More
Reviews
There are no reviews yet.