DC 12V-36V 15A 500W Brushless Motor Controller BLDC Driver Board Stall Over-current Protection
$30.60
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specification
Operating voltage:DC 12V-36V
Operating Current
Driver Power
Speed Voltage:0.1V-5V
Operating Temperature:-40~85°C
Humidity:90%RH
Stall protection:Yes
Enable Control:Yes
Over-current protection:Yes
Steering control:Yes
Speed control signal:Yes
Size:63 x 42 x 17mm (L x W x H); Probe size 3mm, length:fixing hole center distance 57mm; width:fixed hole center distance 36.5mm
Power terminal Out
VCC(positive power supply)
GND(negative one)
MC(motor phases W)
MB(motor phases V)
MA(motor phase U)
Set for the control side
GND:control terminal ground
VR:the governor end 0-5V(corresponding to 10% of motor speed -100%)
ZF:reversing control(connected to 5V or ground can charge the motor rotation direction)
M:tachometer pulse output(depending on the number of motor poles corresponding to the number of pulse per revolution of the output number)
EL:enable control terminal(connected to 5V ot ground running then 5V, grounding the motor stops)
5V:5V control terminal
Wiring
Control terminal for SET
1. The motor speed control wiring methods:available potentiometer system speed can also be connected to the MCU control, when the potentiometer control wiring, the potentiometer middle pin is connected to VR speed port, potentiometer connected to both ends of 5V and GND terminal voltage more high speed faster.
2. Motor steering control wiring methods:you can switch control can also be connected to the MCU control, to GND in one direction, then in one direction 5V.
3. Pulse speed signal:high and low output . IC can not understand the information with the customer request.
Note
Motor driver board 12-36V DC power input, VCC positive power supply,GND power supply is negative.
Electrical wiring methods:Brushless DC motor for the three lines, corresponding MA/U, MB/V, MC/W
Tips
If you use less than 60W, without additional heat sink , be sure to add more than 60W
heatsink fins drive efficiency without lowering the temperature is too high will shine into permanent damage! The size of the heat sink may be a bad environment based work(recommended cooling surface area greater than 200 square centimeters)!When installing the heat sink ,must pay attention to the back of the module 6 MOS pipe insulation, no insulation, it will be adhered to drive plate permanently damaged! Proposes to add insulation films, both sides of the insulating sheet plus thermal grease!
Package Includes
1 x 12-36V 500W Brushless Motor Controler
Weight | 0.027 kg |
---|
Customers Also Viewed
Ebyte E810-DTU(CAN-ETH) Smart Protocol Conversion GPRS Modem Modbus to TCP/IP CAN Bus Ethernet interface Modbus RTU Gateway
$96.54Smart ModuleAdd to cartSpecificationItemsDescriptionInterfaceEthernet:RJ45, 10/100MbpsCAN:1*5*3.81, ScrewingNetwork protocolIP,TCP/UDP, ARP, ICMP, IPV4Simple transparent transmissionTCP Server,TCP Client,UDP Server,UDP Client,Cloud transparent transmissionData Packing MechanismByte packing and time packingTCP Server connectionSupporting up to 6 TCP connectionsIP accessStatic IP,DHCPDNSSupportCAN Transmit baud rateA total of 15 baud rates from 6Kbps-1000KbpsCAN filtering modeUp to 8 filtration modesCAN data layoutProtocol formatParameter configurationWeb page configurationWorking current82mA@12VVoltage8V~28VDC,Over 28V may …
TP4056 Micro USB 5V 1A Lithium Battery Charging Protection Board TE585 Lipo Charger Module
$4.36Battery Protection ModuleAdd to cartSpecificationProduct name:Lithium Battery Charging BoardInput voltage:5VMaximum charging current:1000 mACharge cut-off voltage:4.2 V + / – 1%Battery overcharge protection voltage:2.5 VBattery over-current protection current:3 AInput interface:micro USBSize:27mm x 17mmHow to Use1. Input port with micro 5pin USB female, can directly use mobile charger for input to the lithium battery,and still retain the input voltage wiring solder …
TP4056 Micro USB 5V 1A Lithium Battery Charging Protection Board TE585 Lipo Charger ModuleRead More
10pcs 10-50W 15Wx2 Audio Power Amplifier DC 6 -18V TDA7297 Module Double Channel
$77.83Amplifier BoardAdd to cartFeatures– Working Voltage:6-18V DC– The onboard TDA7297 audio power amplifier chip, double channel 15WX15W– Speaker for European 4-8 10-50W use– Main pin has led chip, convenient external control device, the onboard– 5.08 (mm) distance between two p terminal 2 road, around a track connection output respectively– The onboard dial potentiometer, output size can adjust the …
10pcs 10-50W 15Wx2 Audio Power Amplifier DC 6 -18V TDA7297 Module Double ChannelRead More
LILYGO TTGO ESP32-Micro32 ESP-32-PICO WIFI Wireless bluetooth Control Module
$20.57Smart ModuleAdd to cartFeatureSeries:ESP32Model:ESP32-+MicroType:Regulator ICPower:1WApplication areas:household appliances, smart home, wearable devices, Internet of Things IoTDescriptionsESP32 vcc range:2.2V-3 6VVBAT:direct to battery (and charger)VUSB:direct to USB(5V)VCC:Output of regulator 3.3V/600mAUp to 250mA during RF transmissionsWirelessWifi:802.11 b/g/n/e/iWPA/WPA2/WPA2-Enterprise/SPSbluetooth:bluetooth 42BLESize:1.9×1.3cm/0.75×0.51inchNotePlease allow 1-3mm error due to manual measurement. pls make sure you do not mind before you bid.Due to the difference between different monitors, the …
LILYGO TTGO ESP32-Micro32 ESP-32-PICO WIFI Wireless bluetooth Control ModuleRead More
50Pcs 915MHz SW915-TH12 Copper Spring Antenna for Wireless Communication Module
$28.90Module ComponentsAdd to cartFeaturesSW915-TH12 copper spring antenna is a special antenna for 915MHz wireless communication system design. The antenna has good standing wave ratio, compact shape, ingenious structure, convenient installation, stable performance and good anti-vibration and aging ability.SpecificationFrequency range:915 MHz (+/-5)Standing wave ratioInput impedance:50Maximum power:5WGain:2.15 dBiWeight:1gHeight:12.5+/-1 mm (9T)Antenna color:copperInterface Form:Direct WeldingPackage included50 x Antenna
5Pcs 360 Degree Rotary Encoder Module Encoding Module
$11.83Other Module BoardAdd to cartFunctional characteristics and technical parameters 1)Nominal voltage:DC 5V 2)Wire A, B:0.5mA (Max 5mA; Min 0.5mA) 3)Common wire:1mA (Max 10mA; Min 0.5mA) 4)Temperature range:-30→ to+80→ 5)Output signal A , B phase position output square wave, when clockwise rotation, A phase position pull ahead B phase position 90 °, when anti-clockwise, B phase position pull ahead A …
5Pcs 360 Degree Rotary Encoder Module Encoding ModuleRead More
RD21F Delay Relay Module Power for Delay off Fan Module AC 100V-220V Time 0.2S-300min Adjustable Delay
$13.11Relay ModuleAdd to cartSpecificationsVoltage:100V-220V ACPower consumptionOutput:The output voltage is the same as the input voltage, and the maximum power supply capacity is 10A.Size:88* 36 * 22mmScrew hole:center distance 83mm * 31mm, aperture 3.2mmTime range:(4 files, selected by switch)First gear:range 0.2 seconds-30 seconds, accuracy:0.1 secondsSecond gear:range 0.2 seconds – 300 seconds (5 minutes), accuracy:0.3 secondsThird gear:range 0.2 seconds-30 minutes, …
Reviews
There are no reviews yet.