DC 12V-36V 15A 500W Brushless Motor Controller BLDC Driver Board Stall Over-current Protection
$30.60
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specification
Operating voltage:DC 12V-36V
Operating Current
Driver Power
Speed Voltage:0.1V-5V
Operating Temperature:-40~85°C
Humidity:90%RH
Stall protection:Yes
Enable Control:Yes
Over-current protection:Yes
Steering control:Yes
Speed control signal:Yes
Size:63 x 42 x 17mm (L x W x H); Probe size 3mm, length:fixing hole center distance 57mm; width:fixed hole center distance 36.5mm
Power terminal Out
VCC(positive power supply)
GND(negative one)
MC(motor phases W)
MB(motor phases V)
MA(motor phase U)
Set for the control side
GND:control terminal ground
VR:the governor end 0-5V(corresponding to 10% of motor speed -100%)
ZF:reversing control(connected to 5V or ground can charge the motor rotation direction)
M:tachometer pulse output(depending on the number of motor poles corresponding to the number of pulse per revolution of the output number)
EL:enable control terminal(connected to 5V ot ground running then 5V, grounding the motor stops)
5V:5V control terminal
Wiring
Control terminal for SET
1. The motor speed control wiring methods:available potentiometer system speed can also be connected to the MCU control, when the potentiometer control wiring, the potentiometer middle pin is connected to VR speed port, potentiometer connected to both ends of 5V and GND terminal voltage more high speed faster.
2. Motor steering control wiring methods:you can switch control can also be connected to the MCU control, to GND in one direction, then in one direction 5V.
3. Pulse speed signal:high and low output . IC can not understand the information with the customer request.
Note
Motor driver board 12-36V DC power input, VCC positive power supply,GND power supply is negative.
Electrical wiring methods:Brushless DC motor for the three lines, corresponding MA/U, MB/V, MC/W
Tips
If you use less than 60W, without additional heat sink , be sure to add more than 60W
heatsink fins drive efficiency without lowering the temperature is too high will shine into permanent damage! The size of the heat sink may be a bad environment based work(recommended cooling surface area greater than 200 square centimeters)!When installing the heat sink ,must pay attention to the back of the module 6 MOS pipe insulation, no insulation, it will be adhered to drive plate permanently damaged! Proposes to add insulation films, both sides of the insulating sheet plus thermal grease!
Package Includes
1 x 12-36V 500W Brushless Motor Controler
Weight | 0.027 kg |
---|
Customers Also Viewed
3Pcs Mini PAM8403 3Wx2 5V Dual Channel USB Power Audio Amplifier Board Volume Control
$7.13Amplifier BoardAdd to cartSpecificationOperating voltage:2.5V-5.5VMaximum output power:3W*2(5V 4┯)PCB size:Length:30mm* Width:21mm(Overall height after installed is about 16mm.)Note1.Please make sure the power supply is not more than 5.5V and please don’t do reverse polarity for ‘+’ and ‘-‘, or else, it will burn the board.2.This PAM8403 Audio Amplifier board could be powered by USB Power supply.Package Included3 x Amplifier Board
5pcs D222 Speaker Frequency Drvider Crossover Filters with Junction Box
$30.44Amplifier BoardAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.FeaturesFrequency divider is a circuit arrangement inside the sound box, to distinguish the sound signals of different frequencies (treble, tenor, bass), respectively to enlarge, and then sent to the speaker of the …
5pcs D222 Speaker Frequency Drvider Crossover Filters with Junction BoxRead More
DIY Wind Turbine Generator Model Science Education Experiment Physical Teaching Tool Creative Toy
$37.95PhysicsAdd to cartDescription– Good choice for teaching physical DC wind power generation principle.SpecificationRated Power:0.1(W)Output Voltage:5(V)Wind Wheel Diameter:0.055(m)Blade Quantity:3PcsRated Wind Speed:3.3(m/s)Finished Product Size(LxWxH):95mmx75mmx120mmBattery:3 Sections AA Battery(not included) Features1. The model is packaged by completely accessory sets ,you need to assemble by yourself ,just enjoy the DIY fun.2. Advanced design ,high utilization rate of wind energy, no matter where …
KING PIGEON M210T 4 Switch DIN Wet Contact input + 1 RS485 + 1 RJ45 industrial Ethernet IO Remote Acquisition Module
$139.08Network ModuleAdd to cartNote:Please refer to the title for the actual supported functions.This M210T version:Support 4DI+1RS485+ 1RJ45 wet contactDocumentsManual:Click here to openTool:Click here to openThe difference between switch input dry contact and wet contactDry contactExternal disconnection:the corresponding internal data is 0External closure:the corresponding internal data is 1Wet contactLogic 0:0-3VDCLogic 1:10-30VDCIntroductionThe M210T Ethernet Remote I/O Module is an industrial …
5pcs DIY Digital Display LED Logic Pen Electronic Kit High and Low Level Test Circuit Soldering Practice Board Kit
$13.68DIY Electronic KitsAdd to cartDescriptionPower supply:DC 4.5-5VBoard size:3.5 * 5.5cmLow-level judgment voltage:0.0-0.4VHigh-level judgment voltage:3.3-5VPackage included5 x DIY Digital Display LED Logic Pen Electronic Kit
3Pcs 4S 14.8V 16.8V 18650 Lithium Battery Protection Board Startable Electric Drill 40A Current
$16.28Battery Protection ModuleAdd to cartSpecificationsScope of application:Lithium batteries with nominal voltages of 3.6V and 3.7VProduct size:46*60*3.4mmProduct weight:10.3gCharging voltage:16.8V-18.1VContinuous discharge current (upper limit):40A (If the heat dissipation environment is not good, please reduce the load current to use)Continuous charging current (upper limit):20AApplicable electric drill:electric drill with starting current below 80A and power below 135W.Note1. To start the electric drill successfully, …
Pressure Reducer Mig Tig Flow Meter Control Valve Regulator for Gauge Welding Gas CO2 Argon
$80.99Electrical Pump & ValveAdd to cartDescriptionPressure Reducer Mig Tig Flow Meter Control Valve Regulator for Gauge Welding Gas CO2 Argon FeaturesThe pressure gauge which shows how much gas is left in the tank goes from 0 to 4000 psi.And this flowmeter does not use a diaphragm,so it is more reliable than the flow-gauge style regulators.The output flow is adjustable from …
Pressure Reducer Mig Tig Flow Meter Control Valve Regulator for Gauge Welding Gas CO2 ArgonRead More
Reviews
There are no reviews yet.