HW-M543 DC12V~24V/AC220V intelligent Digital Display Temperature and Humidity Controller
$46.56
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specification
Name:Digital Display Temperature and Humidity Controller
Brand:HW
Model:HW-M543
Control type:temperature and humidity
Working Voltage:DC 12V~24V/AC 220V
Output capacity:maximum 10A
Measurement object:air, water
Temperature range:-20~60 →
Temperature measurement error:÷0.1 →
Humidity range:0-100 %RH
Humidity measurement error:0.2 %
Installation type:Embedded
Dimensions:105*70*38 mm
Hole size:81*57 mm
Weight:About 154g
Package included
1 x Temperature and Humidity Controller
Setting instructions
1. Correctly connect the power supply and the temperature and humidity control equipment according to the wiring diagram, pay attention not to connect the temperature and humidity control equipment wrongly. When connecting the DC12~24V power supply, you must distinguish the positive and negative poles. AC220V does not divide the zero live wire.
2. Stop temperature setting
Press the set button (SET), when the red screen number starts to flash, press the up and down buttons to adjust and set the stop temperature you want; after setting, wait for 10 seconds without operation, the system automatically saves the data.
3. Heating or cooling mode setting
Long press the up button, when the red screen displays C-0, press the set button to enter the C-0 mode setting, press the up and down buttons to switch between the blue screen L and H, L stands for heating, H stands for cooling. (Note:The temperature control load you connect to at L must be a heating device, and at H, the load you connect must be a refrigerating device.) After setting, wait 10 seconds, the system automatically saves the data.
4. Temperature difference setting
Long press the up key, when the red screen shows C-0, press the up and down keys to switch to the C-1 temperature difference setting, press the setting key again to enter the temperature difference setting, and then press the up and down keys to adjust the setting you want Temperature difference value; wait 10 seconds after setting, the system automatically saves the data. (If the stop temperature is set to 35C, the mode is set to L heating mode, and the temperature difference is set to 5, then the start temperature is 35-5=30C and the temperature control range is between 30~35C. On the contrary, if the mode is set to H cooling mode , Then the starting temperature is 35 + 5=40C, and the temperature control range is between 35~40→)
5. Temperature calibration
Long press the up button, when the red screen displays C-0, press the up and down buttons to switch to the C-2 temperature correction mode, press the setting button once to enter the correction mode, and then press the up and down buttons to adjust and set the difference you want If the actual temperature is 28C and the probe detection temperature is 28.2C, then the correction difference can be set to -0.2; if the detection temperature is low, the correction difference can be adjusted higher. After setting, wait 10 seconds, the system will automatically save the data.
6. Stop humidity setting
Press the set button (SET), the red screen numbers start to flash, press the set button again to switch to the blue screen numbers flashing, and then press the up and down keys to adjust and set the stop humidity value you want; after setting, wait for 10 without operation Seconds, the system automatically saves the data.
7. Humidification or dehumidification mode setting
Long press the adjustment key, when the red screen displays H-0, press the set key to enter the H-0 mode setting, press the up and down keys to switch between the blue screen L and H, L stands for humidification, H stands for dehumidification. (Note:The humidity control load you connect to at L must be a humidifying device, and at H, the load you connect to must be a dehumidifying device.) After setting, wait 10 seconds, and the system automatically saves the data.
8. Humidity difference setting
Long press the adjustment key, when the red screen displays H-0, press the up and down keys to switch to the H-1 humidity difference setting, press the setting key to enter the humidity difference setting, press the up and down keys to adjust the setting you want After setting the difference, wait 10 seconds, the system automatically saves the data. (If the stop humidity is set to 50%RH, the mode is set to L humidification mode, the humidity difference is set to 5%RH, then the start humidity is 50-5=45%RH, and the humidity control range is between 45-50%RH, on the contrary If the mode is set to H dehumidification mode, then the starting humidity is 50 + 5 = 55%RH, and the humidity control range is between 50~55%RH)
9. Humidity calibration
Long press the adjustment key, when the red screen displays H-0, press the up and down keys to switch to the H-2 humidity correction mode, press the set key once to enter the correction mode, press the up and down keys to adjust the set difference; such as actual humidity It is 56%RH, the humidity detected by the probe is 56.2%RH, then the correction difference can be set to -0.2; if the detection temperature is low, the correction difference can be adjusted higher. After setting, wait 10 seconds, the system automatically saves the data.
CodeNamePredetermined areaDefault parameters
H-0Mode settingL:Humidify H:DehumidificationL:Heating mode
H-1 Humidity difference0.1-50%RH10%RH
H-2Humidity calibration-10 and 10%RH0.0%RH
10. Restore factory settings
Press the up and down keys at the same time for 5 seconds, when the screen displays 888, the factory restoration is complete.
Weight | 0.132 kg |
---|
Customers Also Viewed
LILYGO TTGO T-Watch SIM800L Bottom Programable PCB Expansion Board for Smart Box Development
$27.49Expansion Board & ShieldAdd to cartFeaturesDevelopment platform:ESP-IDF (native SDK), , Lua, MicroPython, ScratchSupport SIM card mobile communication functionSupport microphoneSupport voiceSupport for scalable module useCode:Click here to openESP32:Characteristic:DescriptionGPIO05:CS:Screen, TFT_CSGPIO18:SCLK:Screen, TFT_SCLKGPIO19:MOSI:Screen, TFT_MOSIGPIO27:DC:Screen, TFT_DCGPIO12:BL:Screen, TFT_BLESP32:Characteristic:DescriptionGPIO33:TX:SIM Card, UART_SIM_TXGPIO34:RX:SIM Card, UART_SIM_RXGPIO14:RST:SIM Card, SIM_RSTGPIO15:PWKEY:SIM Card, SIM_PWKEYGPIO04:BOOST:SIM Card, SIM_BOOST_CTRLPackage includes1 x T-Watch SIM800L PCB backplane1 x AntennaWiring with the T-watch box, for reference only, the T-watch does …
50 Pieces Fountain Pens Holder Wooden Pen Display Case with Antique Color Container 5 Layer
$278.83PhysicsAdd to cartSpecificationsColor:ArchaizeMaterial:Wood Box + Plexiglass CoverSize(L x W x H):about 270*200*245mm[Conversion:1mm=0.03937 inch, 1inch=25.4 mm]Features-Large pen cases, 50 mounted large-capacity, generous and practical design.-Wood box and beige color flannel inside, clear and elegant.-Durable without deformation, glass shatterproof, can be clearly seen.Package Included1 PCS x Wooden Pen Case(Pen not included)Note-Due to different producing batches, product details might be …
50 Pieces Fountain Pens Holder Wooden Pen Display Case with Antique Color Container 5 LayerRead More
220V 700W Powered Portable Electric Air Space Heater Fast Heating thermostat Hot
$58.71Solar CollectorsAdd to cartFeatures-The popular choice for heating bathrooms as well as kitchens.-Overheat protect.-Adjustable thermostat.-Handy carry handle.-Easy to adjust manual controls.-Anti-fire safety protection and are simple to install.Specification-Size:260mm*95mm*160mm-Rated voltage:220V-Colour:White-Rated power:700W-Mode of operation:mechanical-Rated power:700w-Switch type:knob type-Applicable area:21-30m2Package list-1x electric heater
50PCS 5ml Plastic Sample Small Bottle Vial Storage Container Test Tube for Lab
$24.29Bottles & JarsAdd to cartDescription50PCS 5ml Plastic Test Tube Centrifuge Tubes Bottle With Cap For Lab Supplies,Used to plug a flask or testtube for safe keeping. Test Tube. Used to mix, heat, or store substances.SpecificationMaterial:PPContain:5mlWeight:100g(50PCS)Color:TransparentQuantity:50pcsDiameter:14mmHeight:42mmFeatures1.Plastic cryogenic vial.2.Made from PP with good temperature resistance and sealing property.3.Various capacity with clear scale marked,easy to use.4.Self stnading design,no slide when using.5.Smooth side …
50PCS 5ml Plastic Sample Small Bottle Vial Storage Container Test Tube for LabRead More
3pcs 40W DC-AC inverter Power Supply 12V Liter 220V Step Up Transformer Boost Module Support in Parallel
$20.68Power Supply ModuleAdd to cartFeature1. Output DC and AC dual output, can output DC and AC voltage, fully compatible with all kinds of electric appliances2. Without connecting wires, you need to solder the input and output wires yourself.3. Instructions for use:This product can convert the DC power of 8V-13V battery into 220V AC power for household use, and DC …
45Pcs Solar intelligent Watering Timer Automatic Drip Irrigation + 10M Hose + Solar Panel + Copper Filter Nozzle
$109.34Electrical Relay & TimersAdd to cartFeatures> IP67 Waterproof> Indoor or oytdoor use.> Use clean water only.> Automatic water your plants and flowers precisely and at ease.> Reduce water by 70% over traditional sprinklers by focusing water directly to the root.> Flowers, plants, bonsai and potted fruit, for family homes, hotels, clubs, offices and other plants of intelligent care.> Watering the …
10Pcs 3W 5V LED Module Board High Power Module
$26.08LED BoardAdd to cartFeatureColor temperature:Warm White 3000-3200K / white 6000-6500KForward current:700MALuminous flux:White 180-200LM (lumens) , Red 90-100LM (lumens) , Green 80-90LM (lumens)Forward voltage:3.3 – 3.6 VReverse voltage:5VPower:3WViewing angle:180Working temperature:-20 to 60Storage temperature:20 to 60test cod (Click here)Package included10 x LED module
Reviews
There are no reviews yet.