HW-M543 DC12V~24V/AC220V intelligent Digital Display Temperature and Humidity Controller
$46.56
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specification
Name:Digital Display Temperature and Humidity Controller
Brand:HW
Model:HW-M543
Control type:temperature and humidity
Working Voltage:DC 12V~24V/AC 220V
Output capacity:maximum 10A
Measurement object:air, water
Temperature range:-20~60 →
Temperature measurement error:÷0.1 →
Humidity range:0-100 %RH
Humidity measurement error:0.2 %
Installation type:Embedded
Dimensions:105*70*38 mm
Hole size:81*57 mm
Weight:About 154g
Package included
1 x Temperature and Humidity Controller
Setting instructions
1. Correctly connect the power supply and the temperature and humidity control equipment according to the wiring diagram, pay attention not to connect the temperature and humidity control equipment wrongly. When connecting the DC12~24V power supply, you must distinguish the positive and negative poles. AC220V does not divide the zero live wire.
2. Stop temperature setting
Press the set button (SET), when the red screen number starts to flash, press the up and down buttons to adjust and set the stop temperature you want; after setting, wait for 10 seconds without operation, the system automatically saves the data.
3. Heating or cooling mode setting
Long press the up button, when the red screen displays C-0, press the set button to enter the C-0 mode setting, press the up and down buttons to switch between the blue screen L and H, L stands for heating, H stands for cooling. (Note:The temperature control load you connect to at L must be a heating device, and at H, the load you connect must be a refrigerating device.) After setting, wait 10 seconds, the system automatically saves the data.
4. Temperature difference setting
Long press the up key, when the red screen shows C-0, press the up and down keys to switch to the C-1 temperature difference setting, press the setting key again to enter the temperature difference setting, and then press the up and down keys to adjust the setting you want Temperature difference value; wait 10 seconds after setting, the system automatically saves the data. (If the stop temperature is set to 35C, the mode is set to L heating mode, and the temperature difference is set to 5, then the start temperature is 35-5=30C and the temperature control range is between 30~35C. On the contrary, if the mode is set to H cooling mode , Then the starting temperature is 35 + 5=40C, and the temperature control range is between 35~40→)
5. Temperature calibration
Long press the up button, when the red screen displays C-0, press the up and down buttons to switch to the C-2 temperature correction mode, press the setting button once to enter the correction mode, and then press the up and down buttons to adjust and set the difference you want If the actual temperature is 28C and the probe detection temperature is 28.2C, then the correction difference can be set to -0.2; if the detection temperature is low, the correction difference can be adjusted higher. After setting, wait 10 seconds, the system will automatically save the data.
6. Stop humidity setting
Press the set button (SET), the red screen numbers start to flash, press the set button again to switch to the blue screen numbers flashing, and then press the up and down keys to adjust and set the stop humidity value you want; after setting, wait for 10 without operation Seconds, the system automatically saves the data.
7. Humidification or dehumidification mode setting
Long press the adjustment key, when the red screen displays H-0, press the set key to enter the H-0 mode setting, press the up and down keys to switch between the blue screen L and H, L stands for humidification, H stands for dehumidification. (Note:The humidity control load you connect to at L must be a humidifying device, and at H, the load you connect to must be a dehumidifying device.) After setting, wait 10 seconds, and the system automatically saves the data.
8. Humidity difference setting
Long press the adjustment key, when the red screen displays H-0, press the up and down keys to switch to the H-1 humidity difference setting, press the setting key to enter the humidity difference setting, press the up and down keys to adjust the setting you want After setting the difference, wait 10 seconds, the system automatically saves the data. (If the stop humidity is set to 50%RH, the mode is set to L humidification mode, the humidity difference is set to 5%RH, then the start humidity is 50-5=45%RH, and the humidity control range is between 45-50%RH, on the contrary If the mode is set to H dehumidification mode, then the starting humidity is 50 + 5 = 55%RH, and the humidity control range is between 50~55%RH)
9. Humidity calibration
Long press the adjustment key, when the red screen displays H-0, press the up and down keys to switch to the H-2 humidity correction mode, press the set key once to enter the correction mode, press the up and down keys to adjust the set difference; such as actual humidity It is 56%RH, the humidity detected by the probe is 56.2%RH, then the correction difference can be set to -0.2; if the detection temperature is low, the correction difference can be adjusted higher. After setting, wait 10 seconds, the system automatically saves the data.
CodeNamePredetermined areaDefault parameters
H-0Mode settingL:Humidify H:DehumidificationL:Heating mode
H-1 Humidity difference0.1-50%RH10%RH
H-2Humidity calibration-10 and 10%RH0.0%RH
10. Restore factory settings
Press the up and down keys at the same time for 5 seconds, when the screen displays 888, the factory restoration is complete.
Weight | 0.132 kg |
---|
Customers Also Viewed
BESTEP C25 12V Normally Open Trigger Delay Relay Timer Module Vibration for Home Smart
$8.73Relay ModuleAdd to cartManual:http://myosuploads3.hobbyant.com/products/20190219/20190219034014C255V9V12V.pdfApplicationsThis module is a switch instant turn-on trigger delay module, which can be applied to home intelligent systems, anti-theft alarm delay, door control system, automation equipment control, PLC industrial control, electronic development and so on.Description1. Using advanced high-quality timing chip control, accurate timing, performance is much better than 555 chip;2. The trigger terminal has optocoupler …
BESTEP C25 12V Normally Open Trigger Delay Relay Timer Module Vibration for Home SmartRead More
2.5W Mini Laser Engraving Machine 2-axis Engraving Machine for Wood Plastic Paper Bamboo Horns Leather Sponge Paper
$503.82Laser Engraving MachineAdd to cartProduct instruction and installation please:https://drive.google.com/openid=1MH931sFiPqf-L45WqXmfEAN4TrrFrlu-SpecificationsName:2-axis Engraving MachineModel:969407Size:600*550*150mm/24*22*6inStroke:380*260mm/15*10inCommunication Interface:miniUSBLaser Power:2500mwStepper Motor:42H34SVoltage:AC110-220V to DC12VControl Board Selection:DVP SE 2-axis engraving machine control boardSoftware Support:wifidevelo, Candle, Benbox, GrblController, LiteFire, etc. All GRBL-enabled softwareFeatures-The new custom V-slot aluminum matching rolling bearing X24, the accuracy is better and more stable.-There is no limit to the size and height of the engraving …
10pcs 0.28 inch 3-wire 0-100V Digital Red Display DC Voltmeter Adjustable Voltage Meter
$20.60Test & Measuring ModuleAdd to cartFeature1. The wiring of this voltmeter is simple. The conventional two wires are used, the red is connected to the positive, the black is connected to the negative, and the reverse connection is protected.2. Conventionally, no external working power supply is required, and the measuring voltage can be directly operated. The measuring voltage range is …
10pcs 0.28 inch 3-wire 0-100V Digital Red Display DC Voltmeter Adjustable Voltage MeterRead More
6W 6V 260x140x2.5mm S0506 Portable Semi-flexible Solar Panel with Back Junction Box Single USB Charger + 4xSucker + 2x Carabiner Kit
$32.26Smart Robot & Solar PanelAdd to cartFeatures– Portable and frame design– Standard USB output– thin design make it very easy to carry.– Monocrystalline silicon solar cells and epoxy resin surface seal.– Comes with four suckersSpecifications– Size:Approx. 26x14x0.3cm/ 10.24×5.51×0.12inch-Actual Power:6W– Solar output:6V 1700mA– Voltage regulator tube output:5V 1200mA– USB regulated output:5V 1200mAh– Output:USB 5V ,1200mAh– Charge time:3-5h– Solar open circuit voltage:6.8V (max)– …
DC 7V-24V Audio input Switch Board 4-way Audio Source Switch Board Audio Signal input Switch Board Switch Relay DIY Kit
$18.83DIY Electronic KitsAdd to cartSpecificationName:Audio signal switcherVoltage:DC 7V-24V, AC 6V-18VFunction:Four groups of audio signals are connected at the same time, and one group of signals is outputMethod:Rotary switching, switching once when rotating.Relay switching, zero loss.Application:computer, TV, mobile phone, home theater.Package included1set of Audio signal switcher
22.5V 1.25A 33W AC Power Adapter Charger for iRobot
$66.81AC/DC AdaptersAdd to cartSpecificationsName:AC Power Adapter ChargerInput:AC 100-240V 1.5A 50/60HzOutput:DC 22.5V 1.25A 33WInterface:5.5mm*2.5mmSafe:CE,RohsColor:BlackMaterial:PCSize ①Length:11.3cm ②Width:4.5cm ③Height:3.1cm ④Total Length:120cm (including wire)Fit for iRobot 400 500 600 700 770Features1.With heat dissipation intelligent chip and environmentally friendly material.2.Avoid power leakage and fire prevention.3.Strong and durable,long serve life.4.The tool is simple & easy to use.5.Small and beautifully designed and strong practicability.6.High performance …
22.5V 1.25A 33W AC Power Adapter Charger for iRobotRead More
Desktop Game Fun Game Penguin Ice Breaking Save the Penguin Great Family Education Toys
$28.42MathematicsAdd to cartFeatureThe One Who Make The Penguin Fall OffThe Will Lose This GameDon’t Fall Into The Trap Of The Opponent!See Who Can Get The Final Victory!SpecificationColor:As pictureSize:About 23*23*6CMMaterial:Environmentally Materials,ABS PlasticPackage Include1Set x Penguin Ice BreakingPlease NoteThe Picture is only for reference, please make the object as the standard.
Reviews
There are no reviews yet.