HX-FL25A-A-4MOS 3S 12.6V Lithium Battery Balance Protection Board 11.1V with Balance 15A Overcurrent Overcharge and Overdischarge Protection
$5.79
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specification
Model:HX-3S-FL25A-A
Size:56*45*4.0mm
Maximum operating current:15A
Upper limit instantaneous current:25A
Overcharge voltage range:4.25-4.35v÷0.05v
Over-discharge voltage range:2.5-3.0v÷0.05v
Working temperature:-40~+50→
Storage conditions:-40~+80→
Effective life:>30000 hours
Internal resistance
Quiescent current
Charging voltage:12.6V-13V
Balance current:56mA
Short circuit protection:can protect, delay automatic recovery
Package included
1 x 3S 12.6V Lithium Battery Balance Protection Board
Note
This protection board cannot be used for iron-ion polymer batteries, hand drill battery packs, electric fish machine battery packs, electric bicycle battery packs, 2 pieces in series with 24V use, 1W fisheye LED lights.
The power range described applies to the following products
Massager battery pack, LED lamp backup power supply, 12V electronic products, solar street lamp battery pack, monitoring backup power supply, and other products.
Note:For products with a current above 3A, the battery discharge rate must be above 3C.
The magnification calculation formula:1C battery, 2000 capacity is equal to 2AH*1=2A working current.
3C rate battery, 2000 capacity is equal to 2AH*3=6A working current.
In use, the battery will heat up, which means that the battery rate is not applicable. In this case, it must not be used for a long time, and the battery will be damaged quickly.
Note 1:Wiring 0V (B-), 3.7V (B1), 7.4V (B2), 11.1V (B+) strictly according to the diagram, do not short-circuit intentionally!
Note 2:After the line is connected, it needs to be charged before output.
Note 3:When connecting 3 groups of batteries in series, please ensure that the voltage of each group of batteries is the same. If they are not the same, please charge each group of batteries separately and use them in series. During the discharge test, the battery with the fastest voltage drop is the poor battery.
Note 4:Do not mix good batteries and bad batteries together! The closer the capacity/internal resistance of the 3 sets of batteries, the better! (2 good batteries + 1 poor battery use effect = 3 poor batteries use effect) .
Weight | 0.02 kg |
---|
Customers Also Viewed
Multiple Car Toys Magnetic Puzzle Box Book Educational Book Kids Learning Gift
$52.64MathematicsAdd to cartPackage included10 x Card76 x MagnetsFeatures1.Developing kids’ intelligence.2.Teaching kids to know more words.3.Easy for storage.SpecificationsColor:MulticolorMaterial:Paperboard, MagnetismSize:30x4x21.5cm
Basic Starter Kit UNO R3 Mini Breadboard LED Jumper Wire Button with Box for Geekcreit for Arduino – products that work with official Arduino boards
$18.62Module KitsAdd to cartDescriptionsPerfect for Shield Prototyping and TestingPlastic housing, metal contact clipsAccept wire with diameter 20-29AWGVolatge/current:300V/3-5A400 tie-point2 Power Lanes, Tie-point 1001 Double-strip, Tie-point 300Solderless Breadboard Size:82x55x8.5mmPackage included1 x Uno R3 Development Board1x 400 hole Breadboard10 x 220Ω resistor 5% carbon film10 x 1k resistor 5% carbon film10 x 10k resistor 5% carbon film10 x 100k resistor 5% …
3pcs ESP32-S WiFi + Bluetooth ESP32S Serial to WiFi Dual Antenna Module
$29.27Smart ModuleAdd to cartDescriptionThe main chip uses a low-power dual-core 32-bit CPU with a frequency of up to 240MHz and computing power of up to 600DMIPS.Default 32Mbit SPI Flash, 520KB SRAMSupport SoftAP and Station modeUltra-small 802.11b/g/n Wi-Fi + BT/BLE SoC moduleSupport UART/SPI/I2C/I2S/PWM/ADC/DAC, etc.Support for firmware upgrade (FOTA)Antenna supports onboard antenna or IPEX block outputPackage includes3 x Wifi module
Geekcreit 433MHz DC 12V 10A Relay 1CH Channel Wireless RF Remote Control Switch Transmitter with Receiver
$15.30Smart ModuleAdd to cartIf you need more Transmitter, please buy Product ID:1215079>>>Manual:Click here to openFeaturesEasy to install and easy to carryWith a slidable cover on the remote controlWith a hook on the remote controlUse Learning coding, stable and reliableThe wireless signal can pass through walls, floors and doorsYou can turn on or turn off the receiver with transmitter …
CO2 Refill Adapter Connector Kit W21.8-14 Thread Set for Filling SodaStream
$56.69Electrical Pump & ValveAdd to cartFeature*CO2 Refill Adapter is used to fill CO2 into your Sodastream tank.*Adjustable valve pin ensures compatibility with any cylinder valve variation.*Easy to install and use.*Made of high quality metal, high hardness and durable.Specification*Material:Metal*Color:Silver (As Pictures Show)*Inner Thread:TR21-4*Outer Thread:W21.8-14Package Contents1*CO2 Refill AdapterNotes:The real color of the item may be slightly different from the pictures shown on …
CO2 Refill Adapter Connector Kit W21.8-14 Thread Set for Filling SodaStreamRead More
30pcs 2.5-5.5V TTP223 Capacitive Touch Switch Button Self Lock Module
$15.15Other Module BoardAdd to cartFeatures 1. Size:15*11mm 2. Power:2.5-5.5V 3.Trigger setting mode:(1->Short;0->No Short) AB=00:No-lock High TTL level output; AB=01:Self-lock High TTL level output; AB=10:No-lock Low TTL level output; AB=11:Self-lock Low TTL level output; Package included 30 x 2.5-5.5V TTP223 Capacitive Touch Switch Button Self-Lock Module For
NE555 Pulse Module LM358 Duty and Frequency Adjustable Square Wave Signal Generator Upgrade Version
$6.55Test & Measuring ModuleAdd to cartFeature1. Used as a square wave signal generator to generate square wave signals for experimental development.2. Used to generate a square wave signal that drives the stepper motor driver.3. Generate adjustable pulses for use by the MCU.4. Generate adjustable pulses to control the associated circuitry.Description1. Size:3.5CM * 4.6CM1. The main chip:LM358;2. Input voltage:5V-12VDC.3. Input current:≥100MA;4. …
3pcs LM3915 Level indicator Kit DC9V-12V DIY Electronic Production Module Kit
$13.73DIY Electronic KitsAdd to cartFeatureModel:AUL-10Supply voltage:DC9V-12VAudio input:0~1.5VrmsPCB size:66 x 28mm (L x W)Light row size:62.5 x 5 x 10.7mm (L x W x H)Two indication modes:bar indication and fire spot indication (Realized by MOD short-circuit point)Lamp row offers two kinds of vertical and horizontal installationTin-treated solder padsNote:Before power on, please confirm the polarity of the power supply is correct …
3pcs LM3915 Level indicator Kit DC9V-12V DIY Electronic Production Module KitRead More
Reviews
There are no reviews yet.