5pcs MQ-4 Methane Natural Gas Sensor Module Shield Liquefied Electronic Detector Module
$20.68
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specification
– The gas sensing material used in the MQ-4 gas sensor is tin dioxide (SnO2) with low conductivity in clean air.
– When there is a flammable gas in the environment where the sensor is located, the conductivity of the sensor increases as the concentration of flammable gas in the air increases.
– A simple circuit can be used to convert the change in conductivity into an output signal corresponding to the gas concentration.
– The MQ-4 gas sensor has high sensitivity to butane, propane and methane, and has a good balance between methane and propane.
– This sensor detects a wide range of flammable gases, especially natural gas, and is a low cost sensor for a variety of applications.
– Suitable for monitoring equipment for liquefied gases, natural gas and gas in the home or industry. Excellent resistance to ethanol and smoke.
Features
1. It adopts high quality double panel design with power indication and TTL signal output indication;
2. It has DO switch signal (TTL) output and AO analog signal output;
3. The TTL output valid signal is low. (When the output is low, the signal light is on, it can be directly connected to the MCU or relay module)
4. The voltage of the analog output, the higher the concentration, the higher the voltage.
5. It has good sensitivity to gas and natural gas detection.
6. there are four screw holes for easy positioning;
7. product dimensions:32 (L) * 20 (W) * 22 (H)
8. has a long service life and reliable stability
9. fast response recovery characteristics
Electrical Performance
Dection of gas:Natural gas/Methane
Dection of Concentration:300-10000ppm
Input voltage:DC5V
Power consumption (current):150mA
DO output:TTL digital quantities 0 and 1 (0.1 and 5V)
AO output:0.1-0.3V (relatively non-polluting), the highest concentration voltage is about 4V
Using the chip:AT89S52
Crystal:11.0592MHZ
Baud rate:9600
Compilation environment:Keil
Special Reminder
After the sensor is energized, it needs to be preheated for about 20S, and the measured data is stable. The heating of the sensor is a normal phenomenon, because there is a heating wire inside, if it is hot, it is not normal.
Package Included
5 x MQ-4 Gas Sensor Module
Weight | 0.035 kg |
---|
Customers Also Viewed
Geekwrom HD 3.5 inch TFT Display Shield 800×480 for Raspberry Pi 3B 2B + Acrylic Matching Case Kit
$121.30Raspberry Pi & Orange PiAdd to cartGeekwrom HD 3.5 Inch TFT Display Shield 800×480 For Raspberry Pi 3B 2B + Acrylic Matching Case KitHD 3.5 Inch TFT Display Shield 800×480 For Raspberry Pi 3B 2BFeatures– Demensions:85mm*56.5mm;– Resolution:800 x 480, 3.5 inch;– 267ppi High PPI display screen;– 11ms High Response Time(more than 60 fps);– 160° Wide Viewing Angle;– 900:1 High Contrast Ratio;– …
intelligent Screen Solar Pure Sine Wave Power inverter 1200W-6000W DC To AC 110V 120V Converter
$121.49InvertersAdd to cartWatt 1200W Voltage 12V Type Single digital display / Watt 2200W Voltage 12V Type Single digital display / Watt 3000W Voltage 12V Type Single digital display / Watt 3000W Voltage 24V Type Single digital display / Watt 3000W Voltage 48V Type Single digital displ
500W Aquarium Submersible Stainless Steel Heating Rod Adjustable Heater
$48.59Solar CollectorsAdd to cartDescriptionMaterial:Stainless SteelColor:SilverPlug:US PlugVoltage:220-240V 50HzWattage:500WTemperature range:16-32°CCable Length:120cm/47.24inch(appr.)Heating Rod Length:41cm/16.14inch(appr.)FeaturesMade of stainless steel material, anti-rust, useful and durable.Double insulation & waterproof.Keep the water temperature steady.Suitable for aquarium:500L (for reference only).Simple adjustment and easy to read temperature indicator.Easy to install with 2 strong suckers (mounting distance of 2 suckers is about 9.5cm).Adjustment knob allows you to adjust the …
500W Aquarium Submersible Stainless Steel Heating Rod Adjustable HeaterRead More
5pcs JoyStick Module Shield 2.54mm 5 pin Biaxial Buttons Rocker for PS2 Joystick Game Controller Sensor
$14.30Other Module BoardAdd to cartFeaturejoystick joysticks standard interface module electronic building blocks and 2.54mm pin interface leads.Phillips is a two-way rocker 10K resistor, with the joystick in a different direction, tap the resistance vary. This module uses a 5V supply, the original state X, Y readout voltage of 2.5V or so, when pressed with the direction of the arrow, …
4Pcs Geekcreit Ultrasonic Module HC-SR04 Distance Measuring Ranging Transducers Sensor DC 5V 2-450cm
$9.83Sensor & Detector ModuleAdd to cartDescriptionWorking Voltage:5V(DC)Static Current:Less than 2mA.Output Signal:Electric frequency signal, high level 5V, low level 0V.Sensor Angle:Not more than 15 degrees.Detection Distance:2cm-450cm.High Precision:Up to 0.3cmInput Trigger Signal:10us TTL impulseSignal:output TTL PWL signalMode of connectionVCCtrig(T)ech0(R)GNDUse MethodSupply module with 5V, the output will be 5V while obstacle in range, or 0V if not.The out pin of this module is …
1MHz-700MHZ 3.2W HF VHF UHF FM Transmitter RF Power Amplifier for Ham Radio
$50.29RF amplifierAdd to cartApplicationBroadband RF power amplifier for all types of wireless applications, FM shortwave radios remote control toys, digital radio, etc., enter 1 milliwatt (0DBM) maximum output of 3 watts, 15V voltage supply, broadband work 1MHZ to 700MHZ can be work. As a result of well-designed, low end that can reach 35DBM (3W), at 500M, the output …
1MHz-700MHZ 3.2W HF VHF UHF FM Transmitter RF Power Amplifier for Ham RadioRead More
Reviews
There are no reviews yet.