3pcs MQ-4 Methane Natural Gas Sensor Module Shield Liquefied Electronic Detector Module
$13.03
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specification
– The gas sensing material used in the MQ-4 gas sensor is tin dioxide (SnO2) with low conductivity in clean air.
– When there is a flammable gas in the environment where the sensor is located, the conductivity of the sensor increases as the concentration of flammable gas in the air increases.
– A simple circuit can be used to convert the change in conductivity into an output signal corresponding to the gas concentration.
– The MQ-4 gas sensor has high sensitivity to butane, propane and methane, and has a good balance between methane and propane.
– This sensor detects a wide range of flammable gases, especially natural gas, and is a low cost sensor for a variety of applications.
– Suitable for monitoring equipment for liquefied gases, natural gas and gas in the home or industry. Excellent resistance to ethanol and smoke.
Features
1. It adopts high quality double panel design with power indication and TTL signal output indication;
2. It has DO switch signal (TTL) output and AO analog signal output;
3. The TTL output valid signal is low. (When the output is low, the signal light is on, it can be directly connected to the MCU or relay module)
4. The voltage of the analog output, the higher the concentration, the higher the voltage.
5. It has good sensitivity to gas and natural gas detection.
6. there are four screw holes for easy positioning;
7. product dimensions:32 (L) * 20 (W) * 22 (H)
8. has a long service life and reliable stability
9. fast response recovery characteristics
Electrical Performance
Dection of gas:Natural gas/Methane
Dection of Concentration:300-10000ppm
Input voltage:DC5V
Power consumption (current):150mA
DO output:TTL digital quantities 0 and 1 (0.1 and 5V)
AO output:0.1-0.3V (relatively non-polluting), the highest concentration voltage is about 4V
Using the chip:AT89S52
Crystal:11.0592MHZ
Baud rate:9600
Compilation environment:Keil
Special Reminder
After the sensor is energized, it needs to be preheated for about 20S, and the measured data is stable. The heating of the sensor is a normal phenomenon, because there is a heating wire inside, if it is hot, it is not normal.
Package Included
3 x MQ-4 Gas Sensor Module
Weight | 0.021 kg |
---|
Customers Also Viewed
5065cm Engraving Area Laser Engraving Machine DIY Kit Desktop Laser Cutting Printer-without Laser Module
$356.97Laser Engraving MachineAdd to cart1. Benbox Software & Manual:Click to download2. Assembly Instructions, please check:http://myosuploads3.hobbyant.com/products/20190326/201903260314326550.zipDescriptionThis DIY desktop blue laser engraving machine is ideal for amateurlaser engraving usage with grayscale printing,low-light positioning and freedompositioning functions.It only need you to connect it to the computer,then you canprint any pictures your like with your own creativity.SpecificationsMaterial:stainless steel and acrylicWorking Voltage:DC 12VEngraving Area:65x50cm(maximum)Size:72x63cmControl …
3pcs 0.36 inch DC0V-32V Red LED Digital Display Voltage Meter Voltmeter Reverse Connection Protection
$10.64Test & Measuring ModuleAdd to cartFeature∵ Super high precision∵ Ultra-low startup voltage, red minimum 2.5V, green minimum 2.7V, blue minimum 3.0V. When the power supply voltage is lower than 3.5V, only the brightness is lowered, but the measurement accuracy is not affected.∵ With reverse connection protection, it will not burn.Measuring range:0.00V-32.0VPower supply range:Red DC2.50-32.0V, green DC2.70-32.0V, blue DC3.00-30.0VHighest input:DC32.0V. Note:If …
120A Amplifier Rectifier Filter Supply Power Board High Power Schottky Rectifier Filter Power Supply Board 10000uf 125V
$109.34Other Module BoardAdd to cartSpecification – Power board with double-sided tinplate PCB board, 8 H-itachi 10000uf 125V capacitor, 4 original import disassemble Schottky 30A150V equivalent to 120A bridge heap!– Schottky’s characteristics are fast, small internal resistance (pressure drop naturally low),So the original rectifier than the original power amplifier for the high demand for power.– Input power:Maxmium Double AC 60V(60V-0-60V)– …
8 inch 25W 6V USB Solar Panel Powered Iron Fan Home Cooling Ventilator Camping Laptop Fan
$153.89Solar CollectorsAdd to cartFeaturesThe fan runs when plugged to the solar panel. And it can be used alone by plugged into computer USB port.When plugged to the solar panel, how the fan works depends on the sunlight.When the sunlight is strong, the fan works fast. When the sunshine is not strong enough, the fan may work low or …
8 inch 25W 6V USB Solar Panel Powered Iron Fan Home Cooling Ventilator Camping Laptop FanRead More
10pcs DC 12V 6A 3 String Battery Protection Board Panels Solar Street Lights
$29.51Other Module BoardAdd to cartDescriptionSize:56x45x3mmContinuous working current:Within 6ACharge current:Within 6ABalance charging:YesShort circuit protection:YesFunction:Prevent overcharge, overplay, circuit protectionSuitable assembly:Nominal 3.7V electric core / three stringsPackage Included10 x 12V Battery Protection Board
Practical CPU info 1.6 inch 84×48 Matrix LCD Memory Display Module with Backlight for Raspberry Pi
$20.80Raspberry Pi & Orange PiAdd to cartFeatures∵ 1.6 inch, 84 x 48 pixels matrix LCD∵ Through the Raspberry Pi internal C programming, to Pi running on the CPU occupancy rate and memory occupancy rate display on the LCD screen, be clear at a glance∵ Can be programmed to show what you want to display∵ A backlight jumper back through the software …
Reviews
There are no reviews yet.