Robotdyn with POE Leonardo ETH ATmega32U4 Ethernet W5500 (V2) Development Board
$91.04
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Size Conversion
Inches
Centimeters
Please according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.
Product Overview
If you’re looking to build a network-connected device, RobotDyn Leonardo ETH(V2) is the best solution for you!
Leonardo ETH(V2) is a fully-featured Ethernet-connected device. Depending on your use case, it can act as a server or a net member. In a server role, it will receive requests from other devices and services in local network and internet, and respond or react accordingly. In a net member role, the RobotDyn Leonardo ETH(V2) can collect data from different devices or industrial equipment and send it through the local network or Internet. It can also receive data from local network and internet, and control connected devices and equipment. The RobotDyn Leonardo ETH(V2) can also act as stand-alone unit, providing autonomous reaction based on the defined algorithm in response to network changes or other triggers.
Leonardo ETH(V2) features two devices on one board:Leonardo based on an ATmega32U4 and Ethernet controller based on WizNet W5500 TCP/IP. It also has an optional PoE function (receiving power directly through the Ethernet cable).
W5500 Ethernet
WizNet W5500 is a TCP/IP embedded Ethernet controller. It provides TCP/IP Stack, 10BaseT/100BaseTX Ethernet with full or half-duplex, MACand PHY. W5500 is using a highly efficient SPI protocol, with 80 MHz clocks for high-speed connectivity to Atmega32U4. For lower energy consumption, W5500 provides WOL (Wake on LAN) and Power Off modes.
Ports and buses
Leonardo ETH (V2) has 23 digital input/output ports, seven of which can be used for PWM, and 12 analog ports with 10-bits resolution (0 – 1023). 5 ports have a hardware interrupt feature. The board is equipped with an RJ45, micro USB, DC power jack, and a reset button. Unlike the other Leonardo ETH clones, Leonardo ETH(V2) has three additional digital SPI bus ports D14, D15, D16, which can be also used to communicate with other devices via SPI.
SD-card
The board also features a microSD card socket. A microSD card can be used to save and store the data, which can later be transferred over the network. Digital port D4 (CS-CS2) of the ATmega32u4 is dedicated to work with the microSD. Digital port D10 (SS-CS2) is used by WizNet W5500. The Ethernet controller and microSD card are connected through the SPI bus, which is brought out as a separate ICSP connector with ports D14, D15 and D16.
HID functions
Leonardo ETH(V2) can also act as an HID device. It can be used as a mouse or keyboard on the connected computer, in addition to the CDC sequenced/COM-port. You can program it to control an application on your PC. For example, you can set it up to turn your PC on, and then launch and control certain applications. The board itself can start an ARDUN0 IDE, open a sketchand start the compilation/upload.
Programming in ARDUN0 IDE
Leonardo ETH(V2) can be programmed via an ARDUN0 IDE. Select ARDUN0 Leonardo or Leonardo ETH in the Boards menu, and use the Ethernet2 / Ethernet3 library.
Power supply
Leonardo ETH(V2) can be powered via
USB port (5V, 500mA);
DC-IN Jack, PWC 2.1mm, (supporting 7-24V DC input voltage);
Through an Ethernet cable using PoE (Power over Ethernet) – requires a PoE-enabled switch or a PoE injector.
Note
With PoE version:this item, without PoE version:Product ID 1660664
The PoE module is optional. There are several PoE options available, depending on the PoE equipment you use.
The Active PoE is compliant with 802.3af or 802.3at. It will check the power coming in, if it doesnt meet the device requirements, it just wont power up.
The Passive PoE is a simplified version that does not perform a handshake, so it is important to know what PoE voltage your device supplies requires before plugging in the Ethernet cable and powering it up. If you connect the wrong voltage you may cause permanent electrical damage to the device.
Make sure to select the correct board option with a relevant PoE module.
Specifications
Leonardo ETH V2
Input Voltage (VIN/DC jack):7~24V
Power IN (USB):5V-limit 500mA
Power IN (PoE):Optional module, 48V(Input), 9V(Output)
Digital I/O:23
PWM Output:7
Analog I/O:12
Reserved Pins:D4 is used for SD card select;
D9 is used for SD card detect;
D10 is used for W5500
D14, D15, D16 are used for SPI.
*Optional:D8 is used for W5500 interrupting, D11 is used for W5500 initialization
USB socket:Micro-USB
Ethernet socket:RJ45
PCB Size:53.3≠68.6mm
Card Reader:Micro SD card, with logiclevel convertor
Weight:41g
Leonardo MCU
Microcontroller:ATmega32u4(AVR)
Operating Voltage:5V
Flash memory:32KB of which 4KB used by bootloader
SRAM:2KB
Clock Speed:16MHz
EEPROM:1KB
Ethernet MCU
Microcontroller:Wiznet W5500
PHY compliance:10BaseT/100BaseTX Ethernet. Full and half-duplex
Operating Voltage:3.3V, 5V I/O signal tolerance
Memory:Internal 32Kbytes Memory for Tx/Rx Buffers
TCP/IP Protocols:TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE
PHY Clock Speed:25MHz
Passive PoE (optional)
Ethernet Power (IN):12~48V DC
Output:DC 9V
PoE type:Passive PoE
Documents
Dimensional drawing:Click here to open
Pinout:Click here to open
Schematic:Click here to open
Tutorial:Click here to open
Package includes
1 x Leonardo module
Weight | 0.062 kg |
---|
Customers Also Viewed
DIY AC100-240V 10A Smart Home Breaker Remote Control Switch Module Support ALEXA Voice Control
$21.86Smart ModuleAdd to cartParametersInput:AC 100-240V 50/60Hzmax output:10Aoutput:AC 100-240V 50/60Hzstandby mode:0.3Woperation temp:-30~70°CFunctionsupport ALEXA voice control, APP voice controlAPP remote controlon / off statusAPP setup timer, delay switchShare config with others memberseach APP support 150 smart-home deviceSupport French, Simplified Chinese, Traditional Chinese, English, Spanish, ArabicCaution1. Please follow user guide installation2. Please keep environment without wireless frequency when it is in …
3pcs Green ST16VD 22mm Hole Size 6-100 VDC Digital Voltmeter Round Voltage Detector Tester Mini LED Voltage indicator Signal Light Monitor
$12.23Electronic Accessories & SuppliesAdd to cartDescriptionDisplay type:digital onlyMaterial:Electrical ComponentsColor:Green22 mm Digital DisplayRated Frequnency:50/60 HzMeasuring Range:6-100 V DCRated Power:0.5WMechanical life:1 million timesElectrical life:500000 timesSize:2.8*5cm /1.10inch*1.97inch (D*H)Accuracy Class:highNotePlease allow 1-3mm error due to manual measurement.pls make sure you do not mind before you bid .Due to the difference between different monitors,the picture may not reflect the actual color of the item.Package included3 …
110-250V 10A Travel Universal Adapter Plug Socket Power Adapter
$22.26SwitchesAdd to cartSpecificationsPower input:100-250VCurrent:10AMaterial:ABS PlasticColor:WhiteSize:74mm*50mm*39mm(approx.)FeaturesThis item with fit the plugs in Europe/UK/USA/China/Japan/Australia/Spain and alomost every country in th world.This universal adaptor is a compact one piece unit with 4 international adpators,and provides a child protection safety shutter,power indicator light and surge protector.Tips-This unit does not convert voltage.-Keep this away from children.-Make sure your hands are dry before …
110-250V 10A Travel Universal Adapter Plug Socket Power AdapterRead More
20pcs 3.3V 5V 8 Bit Blue Common Anode LED indicator Display Module DIY Kit
$38.52Display ScreenAdd to cartDescriptionIt can be inserted directly into Breadboard,Ideal for linking up to your Arduiuo UNO Mini Nano Mega2560 DUE Breadboard etc,or others MCU ( AVR STM32 ARM7 ARM9 ARM10 ARM11 PIC C8051 STC MSP430 FPGA/CPLD etc.) SpecificationsColor:BlueWorking Voltage:DC 3-24VPolarity:Common anodeInterface:2.54MM with PIN/2.54MM no PINSize:22.86 x 14.13 x 2.11 mmWeight:1.3gApplicationMCU/ARM/FPGA/Atmega328pPLC MotorElectronic diy kitESP8266/nodemcuNANO/UNO/MEGA2560/BreadboardRaspberry pi 4/robotPackage Incldued20 x …
20pcs 3.3V 5V 8 Bit Blue Common Anode LED indicator Display Module DIY KitRead More
Periscope Model Laboratory Detachable Optical Reflection School Teaching Physics Experiment
$32.39PhysicsAdd to cartFeaturesLearning PointReflection principle of lightRectilinear propagation of light– Physical optical reflection teaching tools.– 360° Rotatable lens, quick detachable, expandable. – Train your children observation capability, thinking and analytical skills.Package Included1 x Periscope Model
USB LED Light Lighting Kit ONLY for Lego 42056 911 GT3 RS Bricks Toys
$19.67DIY Electronic KitsAdd to cartDescriptionThe Product Is Just a Light Kit, Not Included The Model!!!Interface:USBColor:As the picture shownFitmentONLY For Lego 42056 911 GT3 RS Bricks ToysFeaturesEasy to install.LED powered by USB.Make your model more cool.Package Included1 x LED Light Kit(Model Not Included)
Reviews
There are no reviews yet.