Robotdyn with POE Leonardo ETH ATmega32U4 Ethernet W5500 (V2) Development Board
$91.04
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Size Conversion
Inches
Centimeters
Please according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.
Product Overview
If you’re looking to build a network-connected device, RobotDyn Leonardo ETH(V2) is the best solution for you!
Leonardo ETH(V2) is a fully-featured Ethernet-connected device. Depending on your use case, it can act as a server or a net member. In a server role, it will receive requests from other devices and services in local network and internet, and respond or react accordingly. In a net member role, the RobotDyn Leonardo ETH(V2) can collect data from different devices or industrial equipment and send it through the local network or Internet. It can also receive data from local network and internet, and control connected devices and equipment. The RobotDyn Leonardo ETH(V2) can also act as stand-alone unit, providing autonomous reaction based on the defined algorithm in response to network changes or other triggers.
Leonardo ETH(V2) features two devices on one board:Leonardo based on an ATmega32U4 and Ethernet controller based on WizNet W5500 TCP/IP. It also has an optional PoE function (receiving power directly through the Ethernet cable).
W5500 Ethernet
WizNet W5500 is a TCP/IP embedded Ethernet controller. It provides TCP/IP Stack, 10BaseT/100BaseTX Ethernet with full or half-duplex, MACand PHY. W5500 is using a highly efficient SPI protocol, with 80 MHz clocks for high-speed connectivity to Atmega32U4. For lower energy consumption, W5500 provides WOL (Wake on LAN) and Power Off modes.
Ports and buses
Leonardo ETH (V2) has 23 digital input/output ports, seven of which can be used for PWM, and 12 analog ports with 10-bits resolution (0 – 1023). 5 ports have a hardware interrupt feature. The board is equipped with an RJ45, micro USB, DC power jack, and a reset button. Unlike the other Leonardo ETH clones, Leonardo ETH(V2) has three additional digital SPI bus ports D14, D15, D16, which can be also used to communicate with other devices via SPI.
SD-card
The board also features a microSD card socket. A microSD card can be used to save and store the data, which can later be transferred over the network. Digital port D4 (CS-CS2) of the ATmega32u4 is dedicated to work with the microSD. Digital port D10 (SS-CS2) is used by WizNet W5500. The Ethernet controller and microSD card are connected through the SPI bus, which is brought out as a separate ICSP connector with ports D14, D15 and D16.
HID functions
Leonardo ETH(V2) can also act as an HID device. It can be used as a mouse or keyboard on the connected computer, in addition to the CDC sequenced/COM-port. You can program it to control an application on your PC. For example, you can set it up to turn your PC on, and then launch and control certain applications. The board itself can start an ARDUN0 IDE, open a sketchand start the compilation/upload.
Programming in ARDUN0 IDE
Leonardo ETH(V2) can be programmed via an ARDUN0 IDE. Select ARDUN0 Leonardo or Leonardo ETH in the Boards menu, and use the Ethernet2 / Ethernet3 library.
Power supply
Leonardo ETH(V2) can be powered via
USB port (5V, 500mA);
DC-IN Jack, PWC 2.1mm, (supporting 7-24V DC input voltage);
Through an Ethernet cable using PoE (Power over Ethernet) – requires a PoE-enabled switch or a PoE injector.
Note
With PoE version:this item, without PoE version:Product ID 1660664
The PoE module is optional. There are several PoE options available, depending on the PoE equipment you use.
The Active PoE is compliant with 802.3af or 802.3at. It will check the power coming in, if it doesnt meet the device requirements, it just wont power up.
The Passive PoE is a simplified version that does not perform a handshake, so it is important to know what PoE voltage your device supplies requires before plugging in the Ethernet cable and powering it up. If you connect the wrong voltage you may cause permanent electrical damage to the device.
Make sure to select the correct board option with a relevant PoE module.
Specifications
Leonardo ETH V2
Input Voltage (VIN/DC jack):7~24V
Power IN (USB):5V-limit 500mA
Power IN (PoE):Optional module, 48V(Input), 9V(Output)
Digital I/O:23
PWM Output:7
Analog I/O:12
Reserved Pins:D4 is used for SD card select;
D9 is used for SD card detect;
D10 is used for W5500
D14, D15, D16 are used for SPI.
*Optional:D8 is used for W5500 interrupting, D11 is used for W5500 initialization
USB socket:Micro-USB
Ethernet socket:RJ45
PCB Size:53.3≠68.6mm
Card Reader:Micro SD card, with logiclevel convertor
Weight:41g
Leonardo MCU
Microcontroller:ATmega32u4(AVR)
Operating Voltage:5V
Flash memory:32KB of which 4KB used by bootloader
SRAM:2KB
Clock Speed:16MHz
EEPROM:1KB
Ethernet MCU
Microcontroller:Wiznet W5500
PHY compliance:10BaseT/100BaseTX Ethernet. Full and half-duplex
Operating Voltage:3.3V, 5V I/O signal tolerance
Memory:Internal 32Kbytes Memory for Tx/Rx Buffers
TCP/IP Protocols:TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE
PHY Clock Speed:25MHz
Passive PoE (optional)
Ethernet Power (IN):12~48V DC
Output:DC 9V
PoE type:Passive PoE
Documents
Dimensional drawing:Click here to open
Pinout:Click here to open
Schematic:Click here to open
Tutorial:Click here to open
Package includes
1 x Leonardo module
Weight | 0.062 kg |
---|
Customers Also Viewed
BESTEP 4 Channel 24V Relay Module High And Low Level Trigger for
$10.15Relay ModuleAdd to cartDescription Maximum load:AC 250V/10A, DC 30V/10A. The chip optocoupler isolation, strong driving ability, stable performance, trigger current 5mA. Working voltage is 24V. Every channel of the module can be set up by high jumper or low level trigger. Fault tolerant design, even if the control line is broken, the relay will not act. Power indicator …
BESTEP 4 Channel 24V Relay Module High And Low Level Trigger forRead More
5Pcs CJMCU-3386 MC33186DH1 Automotive Computer Board Idle Speed Throttle Drive Board A H Bridge
$50.91Other Module BoardAdd to cartDescriptionThe 33886 is a monolithic H-Bridge ideal for fractional horsepowerDC-motor and bi-directional thrust solenoid control. The IC incorporatesinternal control logic, charge pump, gate drive, and low RDS(ON) MOSFEToutput circuitry. The 33886 is able to control continuous inductive DC loadcurrents up to 5.0 A. Output loads can be pulse width modulated (PWM-ed)at frequencies up to 10 …
20pcs Light Dependent Resistor LDR 5MM Photoresistor Photoelectric Switch Element Photo Detector 5516
$4.36Module ComponentsAdd to cartSpecificationsModel:5549Voltage(VDC):150Power Consumption(mw):100Ambient Temperature(C):-30~+70Spectral Peak(nm):540Bright Resistance(10Lux)K┯:5-10Response Time(MS):Rise:20 Decline:30Package included20 x Resistor
PWM 20A 12V/24V Auto Solar Panel Solar Charge Controller Battery Charge Adapter LCD USB
$36.44Solar ControllersAdd to cartSpecificationsName:20A 12V/24V LCD Display PWM Solar Panel Charge ControllerModel:C11465Rated voltage:12/24V AUTOCharge current:20ADischarge current:10AMax.PV input power:260W(12V),520W(24V)Max solar input12V battery,the highest 23V24V battery when the highest 46VEqualization:14.2VFloat charge:13.7V (defaul,adjustable)Discharge stop:10.7V(defaul,adjustable)Discharge reconnect:12.6V(defaul,adjustable)Charge reconnect:13VVoltage of open light:Solar panel 8V(Light lights delay)Voltage of close light:Solar panel 8V(Light off delay)USB output:2 way USB output,5V/2A(Max.)Self-consumeOperationg temperature:-35-60℃Color:BlackSize:133.5mmx70mmx35mmFeatureBuild-in industrial micro controller.Big LCD display,all adjustable …
PWM 20A 12V/24V Auto Solar Panel Solar Charge Controller Battery Charge Adapter LCD USBRead More
Waveshare Sensor Expansion Board Supports XBEE Module Compatible for Arduino
$39.35Expansion Board & ShieldAdd to cartDocumentsSchematic:Click here to openSample tutorial:Click here to openWhat do I mainly doArduino is a huge ecosystem. If the Pi interface can be converted to the Arduino standard, it can be connected to a variety of compatible Arduino expansion boards and connected to the Arduino ecosystem to obtain more available resources.I just do this.Basic situationCompatible with …
Waveshare Sensor Expansion Board Supports XBEE Module Compatible for ArduinoRead More
Emakefun DC5V RGB Tricolor Lamp Module 5PIN Anti-reverse Connector Compatible with Lego Jack Fixing
$10.61Sensor & Detector ModuleAdd to cartFeature1. Supply voltage:5V2. Connection method:5PIN anti-reverse connection Dupont line3. Module size:40*22.5mm4. Installation method:M4 screw compatible with Lego jack fixing5. Connection port:PH2.0Package includes1 x RGB Tricolor Lamp Module (the other items are not includes)
Reviews
There are no reviews yet.