Robotdyn with POE Leonardo ETH ATmega32U4 Ethernet W5500 (V2) Development Board
$91.04
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Size Conversion
Inches
Centimeters
Please according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.
Product Overview
If you’re looking to build a network-connected device, RobotDyn Leonardo ETH(V2) is the best solution for you!
Leonardo ETH(V2) is a fully-featured Ethernet-connected device. Depending on your use case, it can act as a server or a net member. In a server role, it will receive requests from other devices and services in local network and internet, and respond or react accordingly. In a net member role, the RobotDyn Leonardo ETH(V2) can collect data from different devices or industrial equipment and send it through the local network or Internet. It can also receive data from local network and internet, and control connected devices and equipment. The RobotDyn Leonardo ETH(V2) can also act as stand-alone unit, providing autonomous reaction based on the defined algorithm in response to network changes or other triggers.
Leonardo ETH(V2) features two devices on one board:Leonardo based on an ATmega32U4 and Ethernet controller based on WizNet W5500 TCP/IP. It also has an optional PoE function (receiving power directly through the Ethernet cable).
W5500 Ethernet
WizNet W5500 is a TCP/IP embedded Ethernet controller. It provides TCP/IP Stack, 10BaseT/100BaseTX Ethernet with full or half-duplex, MACand PHY. W5500 is using a highly efficient SPI protocol, with 80 MHz clocks for high-speed connectivity to Atmega32U4. For lower energy consumption, W5500 provides WOL (Wake on LAN) and Power Off modes.
Ports and buses
Leonardo ETH (V2) has 23 digital input/output ports, seven of which can be used for PWM, and 12 analog ports with 10-bits resolution (0 – 1023). 5 ports have a hardware interrupt feature. The board is equipped with an RJ45, micro USB, DC power jack, and a reset button. Unlike the other Leonardo ETH clones, Leonardo ETH(V2) has three additional digital SPI bus ports D14, D15, D16, which can be also used to communicate with other devices via SPI.
SD-card
The board also features a microSD card socket. A microSD card can be used to save and store the data, which can later be transferred over the network. Digital port D4 (CS-CS2) of the ATmega32u4 is dedicated to work with the microSD. Digital port D10 (SS-CS2) is used by WizNet W5500. The Ethernet controller and microSD card are connected through the SPI bus, which is brought out as a separate ICSP connector with ports D14, D15 and D16.
HID functions
Leonardo ETH(V2) can also act as an HID device. It can be used as a mouse or keyboard on the connected computer, in addition to the CDC sequenced/COM-port. You can program it to control an application on your PC. For example, you can set it up to turn your PC on, and then launch and control certain applications. The board itself can start an ARDUN0 IDE, open a sketchand start the compilation/upload.
Programming in ARDUN0 IDE
Leonardo ETH(V2) can be programmed via an ARDUN0 IDE. Select ARDUN0 Leonardo or Leonardo ETH in the Boards menu, and use the Ethernet2 / Ethernet3 library.
Power supply
Leonardo ETH(V2) can be powered via
USB port (5V, 500mA);
DC-IN Jack, PWC 2.1mm, (supporting 7-24V DC input voltage);
Through an Ethernet cable using PoE (Power over Ethernet) – requires a PoE-enabled switch or a PoE injector.
Note
With PoE version:this item, without PoE version:Product ID 1660664
The PoE module is optional. There are several PoE options available, depending on the PoE equipment you use.
The Active PoE is compliant with 802.3af or 802.3at. It will check the power coming in, if it doesnt meet the device requirements, it just wont power up.
The Passive PoE is a simplified version that does not perform a handshake, so it is important to know what PoE voltage your device supplies requires before plugging in the Ethernet cable and powering it up. If you connect the wrong voltage you may cause permanent electrical damage to the device.
Make sure to select the correct board option with a relevant PoE module.
Specifications
Leonardo ETH V2
Input Voltage (VIN/DC jack):7~24V
Power IN (USB):5V-limit 500mA
Power IN (PoE):Optional module, 48V(Input), 9V(Output)
Digital I/O:23
PWM Output:7
Analog I/O:12
Reserved Pins:D4 is used for SD card select;
D9 is used for SD card detect;
D10 is used for W5500
D14, D15, D16 are used for SPI.
*Optional:D8 is used for W5500 interrupting, D11 is used for W5500 initialization
USB socket:Micro-USB
Ethernet socket:RJ45
PCB Size:53.3≠68.6mm
Card Reader:Micro SD card, with logiclevel convertor
Weight:41g
Leonardo MCU
Microcontroller:ATmega32u4(AVR)
Operating Voltage:5V
Flash memory:32KB of which 4KB used by bootloader
SRAM:2KB
Clock Speed:16MHz
EEPROM:1KB
Ethernet MCU
Microcontroller:Wiznet W5500
PHY compliance:10BaseT/100BaseTX Ethernet. Full and half-duplex
Operating Voltage:3.3V, 5V I/O signal tolerance
Memory:Internal 32Kbytes Memory for Tx/Rx Buffers
TCP/IP Protocols:TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE
PHY Clock Speed:25MHz
Passive PoE (optional)
Ethernet Power (IN):12~48V DC
Output:DC 9V
PoE type:Passive PoE
Documents
Dimensional drawing:Click here to open
Pinout:Click here to open
Schematic:Click here to open
Tutorial:Click here to open
Package includes
1 x Leonardo module
Weight | 0.062 kg |
---|
Customers Also Viewed
5pcs RS232 to TTL Serial Converter Module DB9 Connector MAX3232 Serial Module with Cable
$21.38Converter BoardAdd to cartFeatureIt is widely used in radio modification, phone flash, GPS, vehicle detection, DVD flash, hard disk repair set-top box upgradeIt can be used to program STC MCU, NXP MCU, Renesas MCU, STM32 MCU, N+-2EC MCU CommunicationPort:TX RX VCC GNDChip:domestic MAX3232Package includes5 x Serial Module5 x Cable
Original JYETech 13805K DSO138mini DIY Digital Oscilloscope Kit SMD Pre-soldered with Case
$37.91DIY Electronic KitsAdd to cartDSO138mini brings in the following improvementsBetter structure and smaller size. The bulky pin-headers connecting the LCD and main board in old DSO138 has been eliminated. The soldering of these pin-headers has being found problematic for beginners.USB or battery powered. This makes the scope much more convenient to be used as a portable device. New version …
Original JYETech 13805K DSO138mini DIY Digital Oscilloscope Kit SMD Pre-soldered with CaseRead More
CJMCU-2112 CP2112 Evaluation Sensor for CCS811 Debugging Board USB to I2C Communication Converter Module
$16.67Sensor & Detector ModuleAdd to cartFeatureDirect connection to PC via USBDirect connection to host system via I2CSimple software GUI for easy setup and data loggingDetermine the effects of Temperature & HumidityIntelligent algorithms to output TVOC / eCO2 levelsPackage includes1 x Sensor Module
3 Pcs Red Acrylic Wall Mounted Protective Case Support Cooling Fan for Raspberry Pi 4 Model B
$35.10Raspberry Pi & Orange PiAdd to cartDescription– Wall Mounting Available– Red Blue Black Optional– Support Adding Cooling Fan– Compatible With Raspberry Pi 4B– Make of Transparent Acrylic, could check the board status easilyThere is a Protective Film on the board surface, please take it off before using.Package Included3* RED Acrylic Case Kit
5pcs CTS DTR USB Adapter Pro Mini Download cable USB to RS232 TTL Serial Ports CH340 Replace FT232 CP2102 PL2303 UART TB196
$23.80Converter BoardAdd to cartFeatures– This product use CH340 chips, stable performance, fully compatible with USB1.1,USB2.0,USB3.0 , baud rate up to 256 kbps; – Uses:Replace FT232 for Arduiuo Pro Mini Download – With receiver indicator,transmitter indicator, and power indicator.– Chip:CH340C– Compatible with PRO MINI download port– Board size:18mm x 30mm(Does not include USB ports and pins)– Supports the following …
10Pcs XH Pitch 2.54mm Single Head 4Pin 4Way Wire To Board Connector 15cm 24AWG with Socket
$6.55Electronic Accessories & SuppliesAdd to cartFeatureType:XH2.54 Single Head WirePin Number:4 PinWire Gauge:24AWG Pitch:2.54mmLength:15cmQuantity:10 Sets(10Pcs Single Head Wire + 10Pcs Socket )Note:the cable color may have different.Package included10 x XH2.54 Single-Head 4Pin 4Way Wire To Board Connector10 x Socket
2.4G Wireless Remote Control Module Transmitter and Receiver Module Kit Transmission Reception Communication 6 Channel Output
$8.26Smart ModuleAdd to cartTY24D-TX is the transmitting module, TY24D-RX is the receiving module. The transmitting module only needs to provide 3.3V power supply and transmitting button and one LED as the transmitting status indication. The output port corresponding to the receiving module can output the level signal, and the module has the output status. Select to select the …
2M*45cm Window Film Privacy Static Cling Stained Glass Sticker Home office Decor
$30.50PlasticsAdd to cartSpecificationsMaterial:PVCSize:45cm X 200cmFeatures– Energy-saving and environmental protection. No gum paste, paste can be repeated.– Deadening UV intrusion, protecting indoor objects fading and aging.– Filter light and reduce glare, protect the skin and vision.– Easy to mount and clean.How to use1. First clean the surface of the pasting position, pasting surfaces should be smooth, not be …
2M*45cm Window Film Privacy Static Cling Stained Glass Sticker Home office DecorRead More
Reviews
There are no reviews yet.