Robotdyn with POE Leonardo ETH ATmega32U4 Ethernet W5500 (V2) Development Board
$91.04
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Size Conversion
Inches
Centimeters
Please according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.
Product Overview
If you’re looking to build a network-connected device, RobotDyn Leonardo ETH(V2) is the best solution for you!
Leonardo ETH(V2) is a fully-featured Ethernet-connected device. Depending on your use case, it can act as a server or a net member. In a server role, it will receive requests from other devices and services in local network and internet, and respond or react accordingly. In a net member role, the RobotDyn Leonardo ETH(V2) can collect data from different devices or industrial equipment and send it through the local network or Internet. It can also receive data from local network and internet, and control connected devices and equipment. The RobotDyn Leonardo ETH(V2) can also act as stand-alone unit, providing autonomous reaction based on the defined algorithm in response to network changes or other triggers.
Leonardo ETH(V2) features two devices on one board:Leonardo based on an ATmega32U4 and Ethernet controller based on WizNet W5500 TCP/IP. It also has an optional PoE function (receiving power directly through the Ethernet cable).
W5500 Ethernet
WizNet W5500 is a TCP/IP embedded Ethernet controller. It provides TCP/IP Stack, 10BaseT/100BaseTX Ethernet with full or half-duplex, MACand PHY. W5500 is using a highly efficient SPI protocol, with 80 MHz clocks for high-speed connectivity to Atmega32U4. For lower energy consumption, W5500 provides WOL (Wake on LAN) and Power Off modes.
Ports and buses
Leonardo ETH (V2) has 23 digital input/output ports, seven of which can be used for PWM, and 12 analog ports with 10-bits resolution (0 – 1023). 5 ports have a hardware interrupt feature. The board is equipped with an RJ45, micro USB, DC power jack, and a reset button. Unlike the other Leonardo ETH clones, Leonardo ETH(V2) has three additional digital SPI bus ports D14, D15, D16, which can be also used to communicate with other devices via SPI.
SD-card
The board also features a microSD card socket. A microSD card can be used to save and store the data, which can later be transferred over the network. Digital port D4 (CS-CS2) of the ATmega32u4 is dedicated to work with the microSD. Digital port D10 (SS-CS2) is used by WizNet W5500. The Ethernet controller and microSD card are connected through the SPI bus, which is brought out as a separate ICSP connector with ports D14, D15 and D16.
HID functions
Leonardo ETH(V2) can also act as an HID device. It can be used as a mouse or keyboard on the connected computer, in addition to the CDC sequenced/COM-port. You can program it to control an application on your PC. For example, you can set it up to turn your PC on, and then launch and control certain applications. The board itself can start an ARDUN0 IDE, open a sketchand start the compilation/upload.
Programming in ARDUN0 IDE
Leonardo ETH(V2) can be programmed via an ARDUN0 IDE. Select ARDUN0 Leonardo or Leonardo ETH in the Boards menu, and use the Ethernet2 / Ethernet3 library.
Power supply
Leonardo ETH(V2) can be powered via
USB port (5V, 500mA);
DC-IN Jack, PWC 2.1mm, (supporting 7-24V DC input voltage);
Through an Ethernet cable using PoE (Power over Ethernet) – requires a PoE-enabled switch or a PoE injector.
Note
With PoE version:this item, without PoE version:Product ID 1660664
The PoE module is optional. There are several PoE options available, depending on the PoE equipment you use.
The Active PoE is compliant with 802.3af or 802.3at. It will check the power coming in, if it doesnt meet the device requirements, it just wont power up.
The Passive PoE is a simplified version that does not perform a handshake, so it is important to know what PoE voltage your device supplies requires before plugging in the Ethernet cable and powering it up. If you connect the wrong voltage you may cause permanent electrical damage to the device.
Make sure to select the correct board option with a relevant PoE module.
Specifications
Leonardo ETH V2
Input Voltage (VIN/DC jack):7~24V
Power IN (USB):5V-limit 500mA
Power IN (PoE):Optional module, 48V(Input), 9V(Output)
Digital I/O:23
PWM Output:7
Analog I/O:12
Reserved Pins:D4 is used for SD card select;
D9 is used for SD card detect;
D10 is used for W5500
D14, D15, D16 are used for SPI.
*Optional:D8 is used for W5500 interrupting, D11 is used for W5500 initialization
USB socket:Micro-USB
Ethernet socket:RJ45
PCB Size:53.3≠68.6mm
Card Reader:Micro SD card, with logiclevel convertor
Weight:41g
Leonardo MCU
Microcontroller:ATmega32u4(AVR)
Operating Voltage:5V
Flash memory:32KB of which 4KB used by bootloader
SRAM:2KB
Clock Speed:16MHz
EEPROM:1KB
Ethernet MCU
Microcontroller:Wiznet W5500
PHY compliance:10BaseT/100BaseTX Ethernet. Full and half-duplex
Operating Voltage:3.3V, 5V I/O signal tolerance
Memory:Internal 32Kbytes Memory for Tx/Rx Buffers
TCP/IP Protocols:TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE
PHY Clock Speed:25MHz
Passive PoE (optional)
Ethernet Power (IN):12~48V DC
Output:DC 9V
PoE type:Passive PoE
Documents
Dimensional drawing:Click here to open
Pinout:Click here to open
Schematic:Click here to open
Tutorial:Click here to open
Package includes
1 x Leonardo module
Weight | 0.062 kg |
---|
Customers Also Viewed
20pcs GX12 3 Pin 12mm Male & Female Wire Panel Circular Connector Aviation Socket Plug
$33.36Electronic Accessories & SuppliesAdd to cartDescriptionModel:GX12Metal Material:Zinc AlloyRated Current / Voltage:5A/125VMounting Dimensions:12mmCoupling:Threaded CouplingPackage included20 x 3pin connector
3pcs 3W 5-35V LED Driver 700mA PWM Dimming DC to DC Step-down Module Constant Current Dimmer Controller
$11.42Driver ModuleAdd to cartSpecificationsInput:DC 5-35VOutput:700mA ± 20mADrive 1-10 pcs 3W LEDSupports PWM dimmingHigh level turn off the outputLow level Open the outputLED buck mode to ensure the total total voltage difference is lower than the input supply voltage (2-3V) .Ultra-small size design (length 3.6cm * Width 2cm)Constant output current, low ripple.LED used to ensure the safety, stability, improving …
10Pcs 12V Flashing Pre-Wired LED Ultra Bright Water Clear Bulb with Plastic Shell
$8.73Electronic Accessories & SuppliesAdd to cartColor. Yellow Diameter 5mm / Color. Yellow Diameter 3mm / Color. Red Diameter 5mm / Color. Red Diameter 3mm / Color. Blue Diameter 5mm / Color. Blue Diameter 3mm / Color. White Diameter 5mm / Color. White Diameter 3mm /
USB Rechargeable Electric Water Dispenser Universal Drinking Water Pump Portable Water Bottle Pump
$32.39Switch AccessoriesAdd to cartSpecifications1.Model:CORx42.Material:ABS3.Color:Black4.Voltage:5V5.Power:5W6.Size:13*6.4cm7.Certification:CE certificationFeatures-Charging by USB cable ,Easy to install and use.-The Color Lights Indicate the Battery Voltage:green for high and red for low.-Simple Installation, Easy to Use:just press the switch and water will automatically flow out.-Food grade silicone hose. Non toxic / No smell, cold resistant, High temperature resistance.-Rechargeable Battery:built in a rechargeable lithium battery, can …
DIY Removable CPU Cooler RGB Cooling Fan for intel 775 1150 1151 1155 1156 1366 AMD AM4
$50.29Electronic Accessories & SuppliesAdd to cartSpecificationProduct Name:CPU CoolerCompatible CPU:for Intel/AMDHeatsink Material:Copper & AluminumSize:98x90x135mm / 3.9×3.5×5.3inchApplication:ProcessorBearing Type:HydraumaticPower Interface:4 PinNoise:18dbType:HeatpipeFan Life:50000 hrsFan Speed:2200RPMHeat Pipes Quantity:6Fan Quantity:1Color:5 Colors lightingSupport CPU Platform:for Intel 775/1150/1151/1155/1156/1366 and AMD all platformsFeatures1. Super mute fan with built-in solid state silent capacitor.2. Cool aurora five color lights when running.3. Pure copper heatsink accelerates heat dissipation.Note-The color of the item …
DIY Removable CPU Cooler RGB Cooling Fan for intel 775 1150 1151 1155 1156 1366 AMD AM4Read More
Geekcreit DIY RGB Full Color LED Gravity Sensor Ambient Light Kit
$28.17DIY Electronic KitsAdd to cartDescriptionIn a inchwhite ballinch appearance, You might think this is a sci-fi blockbuster inside the inchenergy ballinch. Of course, you may think so, You can also call her inchBedside lampinch, inchAmbient Lightinch, inchMood lightinch. In addition, the important thing said three times! Gravity Flip transition effect! Gravity Flip transition effect! Gravity Flip transition effect! FeatureFlip …
Geekcreit DIY RGB Full Color LED Gravity Sensor Ambient Light KitRead More
3Pcs 4A XL6009E1 Adjustable DC-DC Step Up Boost Converter Power Supply Module
$12.64Boost & Buck ModuleAdd to cartDescriptionThe XL6009 is a high-performance step-up (BOOST) module with 4A switching current. The module uses the second generation of high-frequency switching technology XL6009E1 as the core chip, performance far more than the first generation of technology LM2577. XL6009 step-up module cost lower, more excellent performance, LM2577 module is about to be eliminated.ultra-wide input voltage 3V …
3Pcs 4A XL6009E1 Adjustable DC-DC Step Up Boost Converter Power Supply ModuleRead More
100W Dimmer Module Dimmer Circuit Board Switch Desk Lamp Dimmer Board
$3.71Driver ModuleAdd to cartFeaturePCB board size:2CM*3.3CMRated power:P=UI; 100W=220V*0.45AModel:100W dimming module;Rated power:100W;Suitable for dimming and speed adjustment of AC motors and lamps below 100W (energy-saving lamps are not supported);Package includes1 x 100W dimming module
Reviews
There are no reviews yet.