Robotdyn with POE Leonardo ETH ATmega32U4 Ethernet W5500 (V2) Development Board
$91.04
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Size Conversion
Inches
Centimeters
Please according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.
Product Overview
If you’re looking to build a network-connected device, RobotDyn Leonardo ETH(V2) is the best solution for you!
Leonardo ETH(V2) is a fully-featured Ethernet-connected device. Depending on your use case, it can act as a server or a net member. In a server role, it will receive requests from other devices and services in local network and internet, and respond or react accordingly. In a net member role, the RobotDyn Leonardo ETH(V2) can collect data from different devices or industrial equipment and send it through the local network or Internet. It can also receive data from local network and internet, and control connected devices and equipment. The RobotDyn Leonardo ETH(V2) can also act as stand-alone unit, providing autonomous reaction based on the defined algorithm in response to network changes or other triggers.
Leonardo ETH(V2) features two devices on one board:Leonardo based on an ATmega32U4 and Ethernet controller based on WizNet W5500 TCP/IP. It also has an optional PoE function (receiving power directly through the Ethernet cable).
W5500 Ethernet
WizNet W5500 is a TCP/IP embedded Ethernet controller. It provides TCP/IP Stack, 10BaseT/100BaseTX Ethernet with full or half-duplex, MACand PHY. W5500 is using a highly efficient SPI protocol, with 80 MHz clocks for high-speed connectivity to Atmega32U4. For lower energy consumption, W5500 provides WOL (Wake on LAN) and Power Off modes.
Ports and buses
Leonardo ETH (V2) has 23 digital input/output ports, seven of which can be used for PWM, and 12 analog ports with 10-bits resolution (0 – 1023). 5 ports have a hardware interrupt feature. The board is equipped with an RJ45, micro USB, DC power jack, and a reset button. Unlike the other Leonardo ETH clones, Leonardo ETH(V2) has three additional digital SPI bus ports D14, D15, D16, which can be also used to communicate with other devices via SPI.
SD-card
The board also features a microSD card socket. A microSD card can be used to save and store the data, which can later be transferred over the network. Digital port D4 (CS-CS2) of the ATmega32u4 is dedicated to work with the microSD. Digital port D10 (SS-CS2) is used by WizNet W5500. The Ethernet controller and microSD card are connected through the SPI bus, which is brought out as a separate ICSP connector with ports D14, D15 and D16.
HID functions
Leonardo ETH(V2) can also act as an HID device. It can be used as a mouse or keyboard on the connected computer, in addition to the CDC sequenced/COM-port. You can program it to control an application on your PC. For example, you can set it up to turn your PC on, and then launch and control certain applications. The board itself can start an ARDUN0 IDE, open a sketchand start the compilation/upload.
Programming in ARDUN0 IDE
Leonardo ETH(V2) can be programmed via an ARDUN0 IDE. Select ARDUN0 Leonardo or Leonardo ETH in the Boards menu, and use the Ethernet2 / Ethernet3 library.
Power supply
Leonardo ETH(V2) can be powered via
USB port (5V, 500mA);
DC-IN Jack, PWC 2.1mm, (supporting 7-24V DC input voltage);
Through an Ethernet cable using PoE (Power over Ethernet) – requires a PoE-enabled switch or a PoE injector.
Note
With PoE version:this item, without PoE version:Product ID 1660664
The PoE module is optional. There are several PoE options available, depending on the PoE equipment you use.
The Active PoE is compliant with 802.3af or 802.3at. It will check the power coming in, if it doesnt meet the device requirements, it just wont power up.
The Passive PoE is a simplified version that does not perform a handshake, so it is important to know what PoE voltage your device supplies requires before plugging in the Ethernet cable and powering it up. If you connect the wrong voltage you may cause permanent electrical damage to the device.
Make sure to select the correct board option with a relevant PoE module.
Specifications
Leonardo ETH V2
Input Voltage (VIN/DC jack):7~24V
Power IN (USB):5V-limit 500mA
Power IN (PoE):Optional module, 48V(Input), 9V(Output)
Digital I/O:23
PWM Output:7
Analog I/O:12
Reserved Pins:D4 is used for SD card select;
D9 is used for SD card detect;
D10 is used for W5500
D14, D15, D16 are used for SPI.
*Optional:D8 is used for W5500 interrupting, D11 is used for W5500 initialization
USB socket:Micro-USB
Ethernet socket:RJ45
PCB Size:53.3≠68.6mm
Card Reader:Micro SD card, with logiclevel convertor
Weight:41g
Leonardo MCU
Microcontroller:ATmega32u4(AVR)
Operating Voltage:5V
Flash memory:32KB of which 4KB used by bootloader
SRAM:2KB
Clock Speed:16MHz
EEPROM:1KB
Ethernet MCU
Microcontroller:Wiznet W5500
PHY compliance:10BaseT/100BaseTX Ethernet. Full and half-duplex
Operating Voltage:3.3V, 5V I/O signal tolerance
Memory:Internal 32Kbytes Memory for Tx/Rx Buffers
TCP/IP Protocols:TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE
PHY Clock Speed:25MHz
Passive PoE (optional)
Ethernet Power (IN):12~48V DC
Output:DC 9V
PoE type:Passive PoE
Documents
Dimensional drawing:Click here to open
Pinout:Click here to open
Schematic:Click here to open
Tutorial:Click here to open
Package includes
1 x Leonardo module
Weight | 0.062 kg |
---|
Customers Also Viewed
BG01 GPS Module GPS+BDS Beidou Dual-mode Satellite Positioning and Navigation Module Wireless Transmission
$16.15Smart ModuleAdd to cartDescriptionThe BG01 is a highly integrated GNSS SOC module, Main chip is GK9501.It is a high-integration Multi-GNSS SOC that supports BDS/GPS/GLONASS/GALILEO/QZSS/SBAS with low power consumption. It integrates DC/DC,LDO, LNA, RF receiver,Base Band, 32-bit RISC CPU, RAM, Flash, RTC and PMU,and provides kinds of interfaces like UART, I2C, SPI and GPIO.The BG01 supports crystal and TCXO …
Wareshare 5 inch VGA HDMI High Definition Display Capacitive Touch Screen Support for NVIDIA Jetson Nano Raspberry Pi
$99.13Display ScreenAdd to cartOverviewThis product is a universal 5-inch HDMI display with 800 x 480 HD resolution and a capacitive touch panel. Support for Raspberry Pi, NVIDIA Jetson Nano and various mini PCs, as well as computer monitors.FeaturesThe hardware resolution is 800*480, and the resolution can be configured by software (up to 1920*1080)Support mainstream mini PCs such as …
3pcs USB To RS232 TTL PL2303HX Cable Adapter Module Converter for
$12.46Electronic Accessories & SuppliesAdd to cartDescriptionUSB TO RS232 TTL PL2303HX Auto Converter Module Adapter 5V Output, provides the best and convenient way to connect your RS232 TTL devices or DEMO BRD. To your computer, via the usb port.SpecificationBuilt-in TTL COM PC-PL2303HX ChipStandard USB type A male and TTL 4 pin connectorCable length:1000mm (39 3/8 in)Simple and Easy way to give …
3pcs USB To RS232 TTL PL2303HX Cable Adapter Module Converter forRead More
Desktop Telephone Wireless Telephone 4G Wireless GSM Desk Phone SIM Card Desktop Telephone Machine
$66.81Switch AccessoriesAdd to cartProtable Wireless Terminal GSM Desk Phone SIM Card Mobile Desktop Telephone SpecificationOperating Frequency:GSM900MHz and GSM1800MHzOutput PowerGSM900 way:Class 4 (2W)GSM1800 mode:Class 1 (1W)Working Temperature:0 ~ 55 degreeRelative Humidity:5 % to 95%Adapter Input Voltage:AC 50Hz, 220V +10%Backup Battery:Ni-MH battery ,1000 mAhStandby Time:48-72 hours , depending on the network status may be ( battery power )Talk Time:2-6 hours, …
CBB60 5Pcs 55UF 450V Water Pump Motor Run Capacitor
$68.39Module ComponentsAdd to cartFeaturesCBB60 Capacitors takes heavy-edge metallized Al/Zn PP film or web-like fuse film as dielectric. Its components are sealed with flame-retardant epoxy resin. It has cylindric outline with high reliability and stability.CBB60 capacitor has features of small size, light weight, small tangent in waste angle, and good self-concrescence. Applicable to startand operation with 50/60Hz. A. C …
CBB60 5Pcs 55UF 450V Water Pump Motor Run CapacitorRead More
3pcs 2S 10A 7.4V 8.4V 18650 Lithium Battery Protection Board Balanced Function Overcharged Protection
$8.59Power Supply ModuleAdd to cartSpecificationsModel:HX – 2S – D20 Overcharging range:4.25-4.35V ( ±0.05V)Over voltage range:2.5-3.0V (± 0.05 V)Maximum working current:13A Working temperature:- 40 – 50 →Maximum instantaneous current:20A Storage conditions:- 40 – 80 →Static current:less than 10uAResistance:less than 300 m ΩShort circuit protection:to protect and restore must chargeCharging Voltage:8.4 V – 9VBoard Size:46 x 20 x 3.6 mmWelding PointB:battery …
CJMCU-219 INA219 I2C Bi-directional Current Power Monitor Sensor Module
$13.11Sensor & Detector ModuleAdd to cartDescriptionCJMCU-219 module is a with I2C interface Bidirectional current / power monitor integrated circuit (IC), and further expand the energy-saving electronic products TI camp. INA219 with the industry’s highest accuracy and smallest size, not only to monitor the voltage drop across a shunt resistor on the sensing shunt supply voltage, while also computing power. The …
CJMCU-219 INA219 I2C Bi-directional Current Power Monitor Sensor ModuleRead More
Reviews
There are no reviews yet.