Robotdyn with POE Leonardo ETH ATmega32U4 Ethernet W5500 (V2) Development Board
$91.04
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Size Conversion
Inches
Centimeters
Please according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.
Product Overview
If you’re looking to build a network-connected device, RobotDyn Leonardo ETH(V2) is the best solution for you!
Leonardo ETH(V2) is a fully-featured Ethernet-connected device. Depending on your use case, it can act as a server or a net member. In a server role, it will receive requests from other devices and services in local network and internet, and respond or react accordingly. In a net member role, the RobotDyn Leonardo ETH(V2) can collect data from different devices or industrial equipment and send it through the local network or Internet. It can also receive data from local network and internet, and control connected devices and equipment. The RobotDyn Leonardo ETH(V2) can also act as stand-alone unit, providing autonomous reaction based on the defined algorithm in response to network changes or other triggers.
Leonardo ETH(V2) features two devices on one board:Leonardo based on an ATmega32U4 and Ethernet controller based on WizNet W5500 TCP/IP. It also has an optional PoE function (receiving power directly through the Ethernet cable).
W5500 Ethernet
WizNet W5500 is a TCP/IP embedded Ethernet controller. It provides TCP/IP Stack, 10BaseT/100BaseTX Ethernet with full or half-duplex, MACand PHY. W5500 is using a highly efficient SPI protocol, with 80 MHz clocks for high-speed connectivity to Atmega32U4. For lower energy consumption, W5500 provides WOL (Wake on LAN) and Power Off modes.
Ports and buses
Leonardo ETH (V2) has 23 digital input/output ports, seven of which can be used for PWM, and 12 analog ports with 10-bits resolution (0 – 1023). 5 ports have a hardware interrupt feature. The board is equipped with an RJ45, micro USB, DC power jack, and a reset button. Unlike the other Leonardo ETH clones, Leonardo ETH(V2) has three additional digital SPI bus ports D14, D15, D16, which can be also used to communicate with other devices via SPI.
SD-card
The board also features a microSD card socket. A microSD card can be used to save and store the data, which can later be transferred over the network. Digital port D4 (CS-CS2) of the ATmega32u4 is dedicated to work with the microSD. Digital port D10 (SS-CS2) is used by WizNet W5500. The Ethernet controller and microSD card are connected through the SPI bus, which is brought out as a separate ICSP connector with ports D14, D15 and D16.
HID functions
Leonardo ETH(V2) can also act as an HID device. It can be used as a mouse or keyboard on the connected computer, in addition to the CDC sequenced/COM-port. You can program it to control an application on your PC. For example, you can set it up to turn your PC on, and then launch and control certain applications. The board itself can start an ARDUN0 IDE, open a sketchand start the compilation/upload.
Programming in ARDUN0 IDE
Leonardo ETH(V2) can be programmed via an ARDUN0 IDE. Select ARDUN0 Leonardo or Leonardo ETH in the Boards menu, and use the Ethernet2 / Ethernet3 library.
Power supply
Leonardo ETH(V2) can be powered via
USB port (5V, 500mA);
DC-IN Jack, PWC 2.1mm, (supporting 7-24V DC input voltage);
Through an Ethernet cable using PoE (Power over Ethernet) – requires a PoE-enabled switch or a PoE injector.
Note
With PoE version:this item, without PoE version:Product ID 1660664
The PoE module is optional. There are several PoE options available, depending on the PoE equipment you use.
The Active PoE is compliant with 802.3af or 802.3at. It will check the power coming in, if it doesnt meet the device requirements, it just wont power up.
The Passive PoE is a simplified version that does not perform a handshake, so it is important to know what PoE voltage your device supplies requires before plugging in the Ethernet cable and powering it up. If you connect the wrong voltage you may cause permanent electrical damage to the device.
Make sure to select the correct board option with a relevant PoE module.
Specifications
Leonardo ETH V2
Input Voltage (VIN/DC jack):7~24V
Power IN (USB):5V-limit 500mA
Power IN (PoE):Optional module, 48V(Input), 9V(Output)
Digital I/O:23
PWM Output:7
Analog I/O:12
Reserved Pins:D4 is used for SD card select;
D9 is used for SD card detect;
D10 is used for W5500
D14, D15, D16 are used for SPI.
*Optional:D8 is used for W5500 interrupting, D11 is used for W5500 initialization
USB socket:Micro-USB
Ethernet socket:RJ45
PCB Size:53.3≠68.6mm
Card Reader:Micro SD card, with logiclevel convertor
Weight:41g
Leonardo MCU
Microcontroller:ATmega32u4(AVR)
Operating Voltage:5V
Flash memory:32KB of which 4KB used by bootloader
SRAM:2KB
Clock Speed:16MHz
EEPROM:1KB
Ethernet MCU
Microcontroller:Wiznet W5500
PHY compliance:10BaseT/100BaseTX Ethernet. Full and half-duplex
Operating Voltage:3.3V, 5V I/O signal tolerance
Memory:Internal 32Kbytes Memory for Tx/Rx Buffers
TCP/IP Protocols:TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE
PHY Clock Speed:25MHz
Passive PoE (optional)
Ethernet Power (IN):12~48V DC
Output:DC 9V
PoE type:Passive PoE
Documents
Dimensional drawing:Click here to open
Pinout:Click here to open
Schematic:Click here to open
Tutorial:Click here to open
Package includes
1 x Leonardo module
Weight | 0.062 kg |
---|
Customers Also Viewed
20pcs DC-DC Buck Regulator Module 9V/12V/24V to 5V USB Charging Vehicle Power Supply Buck Module
$41.78Power Supply ModuleAdd to cartDescriptionProduct size:35.5*17*8.3mmInput voltage range:6-26VThe output voltage is 5.2V (considering the loss of charging line, the output terminal is about 5.2V, and the load terminal is about 5V).The maximum output current is 3A (without the heat sink, the output current is 2A).Note 1:Positive and negative can not be reversed, and the input voltage should not exceed …
3pcs AT Firmware DT-W5G1 5G WiFi Module 2.4g/5g Dual-band Module with Antenna interface for Wireless Image Transmission
$39.69Smart ModuleAdd to cartDescriptionSOC characteristicsBuilt-in 160MHz MIPS RISC processor512K SRAMCommunication rate:72Mbps (20MHz)Optimal balance & LLR quantificationWi-Fi featuresSupport 802.11 a/b/g/n, 2.4-2.5GHz, 4.9-5.85GHz2.4GHz Rx sensitivity:-75dBm/11n HT20 MCS7, Tx Power:21dBm5GHz Rx sensitivity:-74dBm/11n HT20 MCS7, Tx Power:16.5dBmSupport Station, SoftAP modeSupport Wi-Fi Direct (P2P)Supports CCMP (CBC-MAC, counter mode), TKIP (MIC, RC4), WAPI (SMS4), WEP (RC4), CRCP2P discovery, P2P GO mode/GC mode and P2P …
Geekcreit LCR-T3 LCR-T4 Mega328 Transistor Tester Diode Triode Capacitance ESR Meter Assembled
$34.98Power Supply ModuleAdd to cartSpecificationsResistor:0.1ω-50MωCapacitor:25pF-100000uFInductance:0.01mH – 20HWorking power:DC-9VStandby current:0.02uAOperating current:25mAMaterial:Metal+PlasticSize:about 11.1cm/4.37inchx2.6cm / 1.02inchx8.5cm/3.34inch[Conversion:1cm=0.3937 inch, 1inch=2.54 cm]Description1. Add boot voltage detection function2. Automatic detection of NPN and PNP transistors, N -channel and P-channel MOSFET, diodes (including dual diode), thyristors, transistors, resistors and capacitors and other components3. Automatic test out the pin element and displayed on the LCD4. Can be detected …
1Pair IP68 SP13 6Pin Waterproof Air Plug Socket Panel Mount Wire Cable Connector Aviation Plug
$8.73Electronic Accessories & SuppliesAdd to cartDescriptionProduct Name:13MM Waterproof Aviation ConnectorConnector Type:Plug + SocketPin Quantity:6PINWaterproof Level:IP68Rated Current / Voltage:AC 380V/25AWithstand Voltage:AC 1500VCable Range:4-6.5mmMaterial:Plastic, BrassColor:Blue, Black, Gold TonePackage included1 Pair x 13MM Waterproof Aviation Connector
5Pair IP68 SP13 6Pin Waterproof Air Plug Socket Panel Mount Wire Cable Connector Aviation Plug
$30.28Electronic Accessories & SuppliesAdd to cartDescriptionProduct Name:13MM Waterproof Aviation ConnectorConnector Type:Plug + SocketPin Quantity:6PINWaterproof Level:IP68Rated Current / Voltage:AC 380V/25AWithstand Voltage:AC 1500VCable Range:4-6.5mmMaterial:Plastic, BrassColor:Blue, Black, Gold TonePackage included5 Pair x 13MM Waterproof Aviation Connector
230W 7R DJ Disco Stage Head Light Lamp Moving Beam Ballast Power Supply Module
$45.91Power Supply ModuleAdd to cartTechnical SpecificationsMini size, compact design.sturdy and durable.Easy to use and convenient to operate.Application:Commercial, Engineering, Indoor, Outdoor, Professional, SailingFeatures and BenefitsMaterial:PCBVoltage:110-220VWattage:230WType:7R BallastLength:13cm/5inchPackage Includes1 x Power Supply ModuleNotice1. Please allow 1-3cm error due to manual measurement.Pls make sure you do not mind before you bid.2. The color may have different as the difference display,pls understand.
Emakefun DC5V Gesture Sensor Module with 4PIN Anti-reverse Connector Compatible with Lego Jack Fixing
$15.17Sensor & Detector ModuleAdd to cartFeature1. Supply voltage:5V2. Connection method:4PIN anti-reverse connection Dupont line 12C3. Module size:40*22.5mm4. Installation method:M4 screw compatible with Lego jack fixing5. Connection port:PH2.0Package includes1 x Gesture Sensor Module(the other items are not includes)
5pcs 5V 0.6A 3W Qi Standard Wireless Charging DIY Coil Receiver Module Circuit Board Wireless Charging Coil for Smart Phone
$40.93Power Supply ModuleAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.SpecificationsOutput:5V 0.6APower:3WCircuit board size:20 x 20 x 1 mmMagnetic shield size:28 x 28 x 0.1 mmCoil size:24 x 8 x 0.5 mmCoil outer diameter:24mmCoil inner diameter:8 mmApplication:Can be used for wireless charging …
Reviews
There are no reviews yet.