Automatic Irrigation Module DIY Set for Soil Moisture Detection and Automatic Water Pumping
$10.92
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Size Conversion
Inches
Centimeters
Please according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.
Overview
This product does not need programming, not include the microcontroller, so we don’t provide any code.
We don’t provide power, you can use the charging treasure (5V DC) as a power supply, or use 4 AA batteries.
About Testing
1. Test the relay module:connect the relay module VCC to 5V, GND to the ground, and IN to GND, the relay is will beat, if IN is vacant, the relay will restored, so you can hear the “Kaka” sound;
2. Test the soil moisture sensor module:connect the fork probe and transmitter module with two dupont cable, connect the transmitter module VCC to 5V, and GND to the ground. The red power lamp is always on as soon as it is powered on, and the green (blue) led will gleam for once; put the fork probe directly into the water, the green (blue) light will on;
3. Connect the red line of the pump to 5V, black wire to the ground, the water pump will start work. Note that:the test can be performed for 1 second. because it can not expose to the air for a long time.
4. According to the schematic assembly.
Note
1. This product needn’t welding, but it requires you to strip the wire, twist the copper wire together and protect it with black tape.
2. The pump can not run a long time in the air;
3. Connect the system and power, the pump will work all time, it is right, because in the air, the probe can not detect the humidity, if install it to the flowerpot, then it can normally work.
Note:Do not pour water directly onto the soil probe. If the humidity of the water is too high, it will cause the product to rust and become inoperable.
4. Pump without power supply, power supply matched to the other, and water pump is a dc pumps, pump voltage 3 v, with DC3 – use 6 v power supply. (cannot be used directly with 220 v ac voltage)
Pump
DC Voltage:2.5-6V
Working current:130-220mA
Power:0.4-1.5W
Maximum lift:40-110cm / 15.75′-43.4′
Flow rate:80-120L/H
Outside diameter of water outlet:approx. 7.5mm / 0.3′
Inside diameter of water outlet:approx. 4.7mm / 0.18′
Diameter:approx. 24mm / 0.95′
Length:approx. 45mm / 1.8′
Height:approx. 33mm / 1.30′
Wire length:about 15-20cm (red:’ + ‘, black(white):’ – ‘)
Material:engineering plastic
Driving mode:brushless DC design, magnetic driving
Continuous working life of 500 hours
Package Included
1 x L9110S Controller Board
1 x Soil Moisture Probe + Comparison Module
1 x Small Pump
1 x Battery Holder
1 x 50cm Silicone Tube
Weight | 0.062 kg |
---|
Customers Also Viewed
50Pcs 12V Female DC Power Socket Jack Plug Wire Connector Cable CCTV DC 5.5 x 2.1mm
$32.76Module ComponentsAdd to cartFeaturesDC 5.5 x 2.1mm.Wire Specification:0.15mm²Length:Approx. 27cmMax Current Rating:2AMax Power Rating:60WTransmission voltage:1V~38VUsage temperature:-50→~65→Material:Copper WireUse for:Led Driver/ Strip connector/ CCTV Camera.Package Included50 x 12V DC Connector Cables
EMC EMI Low Noise Pre-RF Amplifier 20dB 5MHz-5GHz RFamp002
$87.30RF amplifierAdd to cartParameter1. Power supply voltage:11V-15V DC2. Gain:greater than 20DB in the 30MHz-1GHz frequency band3. Input and output impedance:50┯4. Maximum output power:10dBm5. Input signal:-10DBm6. Bandwidth:30MHz to 3GHz (gain is different under different frequencies)Measured gain (prototype)F=5.0MHZ GAIN=13.15DBF=10.0MHZ GAIN=23.89DBF=30.0MHZ GAIN=27.06DBF=50.0MHZ GAIN=27.92DBF=500.0MHZ GAIN=24.84DBF=1.0GHZ GAIN=22.01DBF=1.5GHZ GAIN=20.72DBF=2.5GHZ GAIN=17.65DBF=3.5GHZ GAIN=10.06DBF=4.0GHZ GAIN=9.09DBF=5.0GHZ GAIN=8.90DB7. Noise figure NF (theoretical value)500MHz@ 0.6dB1GHz@ 0.7dB2GHz@ 0.7dB3GHz@ 1.1dB4GHz@ 1.6dB5GHz@ 2.1dBComparison …
EMC EMI Low Noise Pre-RF Amplifier 20dB 5MHz-5GHz RFamp002Read More
RX24 100W 30R 30RJ Metal Aluminum Case High Power Resistor Golden Metal Shell Case Heatsink Resistance Resistor
$6.55Electronic Accessories & SuppliesAdd to cartFeaturesIt has the characteristics of small size, high power and high precision.It is sealed by professional technology.It has the advantages of stronger heat resistance, higher temperature resistance, moisture resistance, high anti-vibration and explosion protection.Scope of application:Testing power supply, frequency converter, automobile LED lamp, automation equipment, audio, frequency divider, servo industry and other harsh industrial control …
5pcs SRX882 433/315MHz Superheterodyne Receiver Module Board for ASK Transmitter Module
$16.71Smart ModuleAdd to cartItem OverviewThe SRX882 is a super-heterodyne receiver module with a micropower and strong driving force in conjunction with the ASK transmitter module. It has high stability, anti-interference and high cost performance, and also has a strong driving force, which can pass ROHS, FCC, CE and other certifications. The data port can be directly connected to …
5pcs SRX882 433/315MHz Superheterodyne Receiver Module Board for ASK Transmitter ModuleRead More
13.5mm Adjustable Laser Pointer Module Holder Mount Clamp 3 Axis
$42.51Engraving Parts & AccessoriesAdd to cartDescriptionMaterial:stainless steelColor:blackMount Inner Diameter:13.5mmSize:40X60mm/1.57X2.36inch(L*H)Feature1. Stainless steel laser moudle holder2. Professional angle and height adjustable design3. Installed on the laser module,it can become a professional laser pointer or laser locator4. Can also used a as a heatsink for the laser module,extend the laser module life time5. Fit for 12mm diameter laser modulePackage included1X Laser Module Holder
Mask Scary Glow Mask LED Mask for Halloween Mask Party Masks Neon Maske Skeleto Halloween Party Decor
$17.17EL ProductsAdd to cartColor. Red / Color. Orange / Color. Yellow / Color. Blue / Color. Blue / Color. Purple / Color. White / Color. Pink / Color. Fluorescent Green / Color. Green / Color. Transparent Blue /
Reviews
There are no reviews yet.