Automatic Irrigation Module DIY Set for Soil Moisture Detection and Automatic Water Pumping
$10.92
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Size Conversion
Inches
Centimeters
Please according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.
Overview
This product does not need programming, not include the microcontroller, so we don’t provide any code.
We don’t provide power, you can use the charging treasure (5V DC) as a power supply, or use 4 AA batteries.
About Testing
1. Test the relay module:connect the relay module VCC to 5V, GND to the ground, and IN to GND, the relay is will beat, if IN is vacant, the relay will restored, so you can hear the “Kaka” sound;
2. Test the soil moisture sensor module:connect the fork probe and transmitter module with two dupont cable, connect the transmitter module VCC to 5V, and GND to the ground. The red power lamp is always on as soon as it is powered on, and the green (blue) led will gleam for once; put the fork probe directly into the water, the green (blue) light will on;
3. Connect the red line of the pump to 5V, black wire to the ground, the water pump will start work. Note that:the test can be performed for 1 second. because it can not expose to the air for a long time.
4. According to the schematic assembly.
Note
1. This product needn’t welding, but it requires you to strip the wire, twist the copper wire together and protect it with black tape.
2. The pump can not run a long time in the air;
3. Connect the system and power, the pump will work all time, it is right, because in the air, the probe can not detect the humidity, if install it to the flowerpot, then it can normally work.
Note:Do not pour water directly onto the soil probe. If the humidity of the water is too high, it will cause the product to rust and become inoperable.
4. Pump without power supply, power supply matched to the other, and water pump is a dc pumps, pump voltage 3 v, with DC3 – use 6 v power supply. (cannot be used directly with 220 v ac voltage)
Pump
DC Voltage:2.5-6V
Working current:130-220mA
Power:0.4-1.5W
Maximum lift:40-110cm / 15.75′-43.4′
Flow rate:80-120L/H
Outside diameter of water outlet:approx. 7.5mm / 0.3′
Inside diameter of water outlet:approx. 4.7mm / 0.18′
Diameter:approx. 24mm / 0.95′
Length:approx. 45mm / 1.8′
Height:approx. 33mm / 1.30′
Wire length:about 15-20cm (red:’ + ‘, black(white):’ – ‘)
Material:engineering plastic
Driving mode:brushless DC design, magnetic driving
Continuous working life of 500 hours
Package Included
1 x L9110S Controller Board
1 x Soil Moisture Probe + Comparison Module
1 x Small Pump
1 x Battery Holder
1 x 50cm Silicone Tube
Weight | 0.062 kg |
---|
Customers Also Viewed
5pcs TS-300B Turbidity Sensor Detection Module Water Quality Tester Washing Machine Turbidity Transduce
$43.93Sensor & Detector ModuleAdd to cartPrincipleTurbidity sensor TS-300B measures the turbidity (counter of suspended matter) in the wash water. Based on the optical principle, the sensor uses the light-emitting diode and phototransistor to receive the specific wavelength to measure the opacity or other substances of dirty water. concentration. By using phototransistors and light-emitting diodes, the light emitted by the sensor …
3Pcs USB Fan Speed Controller Module Reducing Noise Multi-stall Adjustment Governor DC 4-12V
$20.74Motor PWM Speed ControllerAdd to cartFeatures– USB Fan Air Conditioner – Strong winds and weak wind adjust freely – Stepless Speed Regulation – Suitable for the very common 5.0V USB fan on the market Regulation PrincipleThe non-adjustable fan is a 5V direct fan motor,while the two-stall fan is the interior has a step-up circuit board,when placed in the second gear,the …
5pcs JDY-08 BLE bluetooth 4.0 Serial Port Wireless Module Low Power Master-slave Support Airsync i Beacon
$45.12Smart ModuleAdd to cartFeaturesJDY-08 transparent transmission module is based on bluetooth 4.0 protocol standard, working frequency range is 2.4GHZ range, modulation mode is GFSK, large transmission power is 0db, large transmission distance is 80 meters, TICC2541 chip design is adopted, and users can modify device name by AT command. , service UUID, transmit power, pairing password and other …
ADC Module ADS1100 for Analog Signal Capture Converter Compatible M5StickC ESP32 Mini IoT Development Board Fi
$14.74Converter BoardAdd to cartnull Description ADC_HAT is another type of C-HAT specifically design for M5StickC controller. Same as ADC unit, this is an ADC converter component for stickc. Packed with an ADC converter chip ADS1100, which is a fully differential, 16-bit, self-calibrating, A/D converter. Extremely easy to design with and configure, the ADS1100 allows you to obtain precise …
5pcs Mini MP1584EN DC-DC BUCK Adjustable Step Down Module 4.5V-28V input 0.8V-20V Output
$8.94Power Supply ModuleAdd to cartSpecificationsModel:MP1584Name:DC-DC step-down moduleInput Voltage:4.5V ~ 28VOutput voltage:0.8V ~ 20VOutput Current:3A (Max)Conversion efficiency:96% (maximum)Output RippleSwitching frequency:1.5MHz (highest) typically 1MHzOperating Temperature:-45°C ~ +85°CSize:22mm * 17mm (L * W )Application areas:DIY mobile power, monitor power supply, power buggies, camera power supply, car power, communications equipment supply,etc.Packge included5 x Step Down Module
LILYGO TTGO T-Koala ESP32 WiFi and bluetooth Module 4MB Development Board Based on ESP32-WROOM-32 Micro USB
$26.23Smart ModuleAdd to cartFeatureEspressif official ESP32-WROOM-32 moduleLatest ESP32 version:REV14MB FLASHLithium battery interface, 500mA maximum charging currentCompatible with , MicroPythonDefault firmware:latest MicroPythoTechnical specificationsMicrocontroller:ESP-32Board power supply:(USB) 5VSupport battery:Lipo Battery 3.7VWorking voltage:3.3VFlash:4 MbytesLength:78 mmWidth:27 mmWeight:7.8 gramsPackage includes1 x ESP32 WiFi&bluetooth Broad2 x Pin
Reviews
There are no reviews yet.