3pcs TM1637 4 Bits Digital LED Display Module 7 Segment 0.36 inch RED Anode Tube 4 Serial Driver Board for
$11.00
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Introduction
The module is a 12-pin display module with a 4-point common digital tube (0.36 inch) with a clock point. The driver chip is TM1637. It only needs 2 signal lines to enable the MCU to control the 4-bit 8- Segment digital tube.
Features
Digital Tube:4-digit common anode with a 0.36-inch digital tube with a score point, highlighted in red
Positioning hole:4 M2 screw positioning holes, the hole diameter is 2.2mm, which makes the module easy to install and position, and realize the module combination
Digital tube 8-level grayscale adjustable
Control interface level can be 5V or 3.3V
Size:42 x 24 x 12 mm
Weight:8g
Project:Minimum value:Typical value:Maximum:Unit
Voltage:3.3:5:5.5:VDC
Current (@5V):-:30:80:mA
Pin Description
GND – ground
VCC – the power supply
DIO – the data input and output pin
CLK – the clock signal pin
Overview of the library routines
1. Clock Display:Use the timer 1 of the MCU on the motherboard to time and let the 4-digit display.
2. Number Flow:0~9, A, b, C, d, E, F, and other 16 characters flow from right to left.
3. StopWatch:Use the timer 1 of the MCU on the motherboard to time, and use the button to realize the stopwatch function.
Experiment equipment
An compatible motherboard Catduino (not familiar with open source hardware can be understood as the Atmega328P microcontroller development board) and a mini USB cable;
1 4-digit digital tube display module;
4 male to female DuPont lines for connecting the control interface of the module and the Catduino development board;
Experimental procedure
1. Use 4 male to female DuPont lines 4-digit digital display module Connected to Catduino, as shown in the following table and figure
Catduino:Cable:4-digit digital display module
GND:black line:GND
5V:Red line:VCC
D2:Yellow line:DIO
D3:White line:CLK
2. Connect the Catduino with mini USB. If you are using the motherboard for the first time, its USB to a serial driver can find the USB Drivers from the drivers in the IDE directory.
3. Reopen the IDE and click the Open button on the toolbar to open the NumberFlow routine in DigitalTube.
Select the serial port, board name, click the Burn button, you can burn. This routine can make 16 characters from 0~9, A, b, C, d, E, F, etc. flow from right to left.
The function of adjusting the grayscale of the digital tube is the set() function in class TM1637, and the input parameter is 0~7. The larger the number, the higher the brightness.
Package includes
3 x TM1637 4 Bits Digital LED Display Module
Weight | 0.03 kg |
---|
Customers Also Viewed
20pcs WEAH-122 Speaker Professional Frequency Divider Car Horn Sound Power Crossover
$139.47Amplifier BoardAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.FeatureBrand:WEAHModel:122Power:110WResistance:4-8ohmSize:100x 54 x 28mmFrequency:750-2000HzFiltering Characteristics:Pure Alto CrossoverPackage includes20 x Frequency Divider
DS18B20 Expansion Board Shield for D1 Mini DS18B20 Temperature Measurement Sensor Module
$6.55Expansion Board & ShieldAdd to cartFeatures1. Supporting the D1 MINI2. The Ar-duino compatible, using A-rduino IDE for programming3. 11 the XI/O pins4. 1 XADC pin (0-3.3V)5. Support the OTA onlinePackage included1 x DS18B20 Module2 x Long female pin2 x Short female pin2 x Normal pin
Human Body Pyroelectric infrared induction Alarm Circuit Kit Welding Electronic Training DIY
$8.73DIY Electronic KitsAdd to cartFeatureBoard size:5*4.9cmPower supply voltage:5-6V DCFunction realizationThe human body infrared sensor alarm circuit is composed of pyroelectric infrared sensor PIR1 (D203S), infrared sensor signal processor U1 (BISS0001), voice chip IC1 (C002) and alarm circuit. The circuit can be used as a home anti-theft, without sound, light, vibration, even in a dark state, once it enters the …
CPU info 1.6 inch LCD 84×48 Memory Display Module with Backlight for Raspberry Pi Zero / 1/2 / 3 /3B+
$22.95Raspberry Pi & Orange PiAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.DescriptionThis CPU Info 1.6-inch LCD resolution is 84*48, which can be used in the Pi0/Pi1/Pi2/Pi3 full range of Raspberry Pi. It features a 26Pin GPIO pin header design. The female pin on …
BESTEP 6 Channel 5V Relay Module High And Low Level Trigger
$19.67Relay ModuleAdd to cartDescriptionMaximum load:AC 250V/10A, DC 30V/10A.The chip optocoupler isolation, strong driving ability, stable performance, trigger current 5mA.Working voltage is 5V.Each channel of the module can be set up by high jumper or low level trigger.Fault tolerant design, even if the control line is broken, the relay will not act.Power indicator (green), 6 relay status indicator (red).The …
BESTEP 6 Channel 5V Relay Module High And Low Level TriggerRead More
Reviews
There are no reviews yet.