XY-DJ01 DC6-30V 30A 1CH Digital Display Relay Module Delayed Power off Trigger Delay Cycle Timing Circuit Switch Rail Type
$26.88
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Features
1. With LCD display, the current mode and parameters are clear at a glance, very clear, simple and practical;
2. Support button trigger control, high and low level trigger, switch value control, support NPN, PNP sensor access, suitable for most occasions;
3. Wide voltage supply (6~30V),Rail installation, very convenient to use;
4. There is a key pausing function, with reverse connection protection, reverse connection does not burn;
5. Added sleep mode. After enabling, without any operation for about 5 minutes, the LCD backlight will be automatically turned off; any key to wake up;
6. Different OP, CL, LOP parameters can be set, these parameters are independent of each other and saved separately;
7. All set parameters are automatically saved after power-off.
Operating mode
P0:After the signal is triggered, the relay is turned on for OP time, and then off; within the OP time, the signal is triggered again invalid
P1:After the signal is triggered, the relay is turned on for OP time and then off; within the OP time, the signal is triggered again to re-timing
P2:After the signal is triggered, the relay is turned on for OP time and then turned off; within the OP time, the signal triggers reset again, the relay is turned off, and the timing stops
P3:After the signal is triggered, the relay is turned off for CL time, and then the relay is turned on;
P4:After the trigger signal is given, the relay is turned on for OP time, the relay is disconnected for CL time, and then the above actions are cycled, the signal is given again in the cycle, the initial state is restored, and the timing is stopped; the number of cycles (LOP) can be set; the cycle ends, keep the relay off ;
P5:Give the trigger signal, after the relay is disconnected from the CL time, the relay will be turned on for OP time, and then cycle the above actions, give the signal again in the cycle, restore the initial state, and stop timing; the number of cycles (LOP) can be set; the cycle ends, keep the relay on ;
P6:After power-on, no trigger signal is needed, the relay is on for OP time, the relay is off for CL time, and the above actions are cycled; the number of cycles (LOP) can be set; the cycle is over, keep the relay off;
P7:There is no need to trigger signal after power-on, the relay is off CL time, the relay is on OP time, and the above actions are cycled; the number of cycles (LOP) can be set; the cycle ends and the relay is kept on;
P8:Signal hold function If there is a trigger signal, the timer is cleared and the relay remains on; when the signal disappears, the relay is disconnected after timing OP; during the timing, there is a signal again, and the timer is clear;
P9:Signal hold function If there is a trigger signal, the timer is cleared and the relay remains off; when the signal disappears, the relay is turned on after timing CL; during the timing, there is another signal, and the timer is cleared;
(P0~P7) mode, short press the pausing button, when the system does not trigger the timing, the system starts timing; when the system is already timing, the system pauses timing, the relay is disconnected, and flashes ‘OUT’ as a reminder;
In P8 P9 mode, the pausing button on the running interface is used as the trigger signal, and its button function is disabled by short press/long press;
Product parameter
Working voltage:6-30V power supply
Trigger signal source:high level trigger (3.0V~24V), low level trigger (0.0V~0.2V), switch control (passive switch).
Output capacity:can control equipment within DC 30v 30A or AC 220v 30A
Quiescent current:15mA
Working current:50-130mA
Service life:more than 100,000 times;
Working temperature:-40-85→;
With optocoupler isolation, enhanced anti-interference ability, industrial-grade circuit board, set parameters are always remembered after power failure.
Timing range
0.01 second (minimum) ~ 9999 minutes (maximum) continuously adjustable
How to choose the timing range
In the OP/CL parameter modification interface, short press the pausing button to select the timing range;
XXXX No decimal point, timing range 1 second~9999 seconds
XXX.X The decimal point is in the tenth place, and the timing range is 0.1 seconds to 999.9 seconds
XX.XX The decimal point is in hundreds, and the timing range 0.01 seconds to 99.99 seconds
X.X.X.X All decimal points are lit, timing range 1 minute to 9999 minutes
For example, if you want to set the OP to 3.2 seconds, move the decimal point to the tens place, and the LCD will display 003.2
Parameter description:OP on time, CL off time, LOP cycle times (1-9999 times, ‘—-‘ represents infinite cycles)
parameter settings
a) Enter the setting interface by long pressing the setting button;
b) First set the work mode, the work mode flashes to remind, short press the increase/decrease button to set the work mode;
c) Short press the setting button, select the working mode, and enter the system parameter setting;
d) In the system parameter setting interface, short press the setting button to switch the system parameter to be modified, and short press/long press the increase/decrease button to modify;
(Note:Short press the setting button is invalid in P0~P3/P8/P9 mode);
e) In the OP/CL parameter modification interface, short press the pausing button to switch the timing unit (1s/0.1s/0.01s/1min)
f) After setting all parameters, long press the setting button to save the parameter setting and exit the setting interface;
Additional functions
a)Automatic sleep function:In the running interface (P0~P7 mode), long press the pausing button to start or close the automatic sleep function (LP selects on to start the sleep function, about five minutes, without any operation, the LCD backlight automatically turns off , The system is running normally, any key is pressed to wake up; off is to close the sleep function);
b) Parameter view:In the running interface, short press the SET button to display the current parameter settings of the system, which does not affect the normal operation of the system;
c) Display content switching:In P4 ~ P7 mode, short press the DOWN key to switch the display content (operating time/cycle times);
Package included
1 x Relay Module Switch
Weight | 0.03 kg |
---|
Customers Also Viewed
3Pcs 0.96 inch 4Pin White IIC I2C OLED Display Module 12864 LED
$38.88Display ScreenAdd to cartFeatureOLED Driver IC:SSD1306Resolution:128 x 64Visual Angle:>160°Input Voltage:3.3V ~ 6VCompatible I/O Level:3.3V, 5VMini Size:2.7 x 2.8cmOnly Need 2 I/O Port to ControlFull Compatible , 51NoteIf you decide to buy OLED display, you must confirm that you can make it work by yourself, we’ll haven’t any technology support. Thanks for your understanding and support.Package included3 x 0.96 …
3Pcs 0.96 inch 4Pin White IIC I2C OLED Display Module 12864 LEDRead More
Micro:Bit bluetooth 4.0 Low Energy Open Development Board for Programming
$60.06Raspberry Pi & Orange PiAdd to cartOverviewThe micro:bit is an open development board that allows you to run code on it and have access to all of the hardware.You can use your micro:bit for all sorts of cool creations, from robots to musical instruments – the possibilities are endless.This little device has an awful lot of features, like 25 red LED …
Micro:Bit bluetooth 4.0 Low Energy Open Development Board for ProgrammingRead More
500mL 24/40 Glass Filtering Flask Lab Filtration Conical Flask Bottle Laboratory Glassware
$58.71Glassware KitAdd to cartDescription– Flasks are glass or plastic containers for storing or collecting chemical samples or solutions in scientific laboratories.– It shaped like a cone with a wide, flat base that narrows to a neck opening, which can be closed with a stopper or cap.SpecificationMaterial:Borosilicate GlassCapacity:500mLFlask Style:Filtering (vacuum)Feature– The neck is 24/40 Ground Joint.Package Included1 x Glass …
500mL 24/40 Glass Filtering Flask Lab Filtration Conical Flask Bottle Laboratory GlasswareRead More
AC 100W 40KHZ Ultrasonic Cleaning Power Driver Board with 50W 40K Transducer 220V
$98.40Driver ModuleAdd to cartSpecificationsPower:220V 100WPendulum:50W 40KHZApplies to:Low-power ultrasonic cleaning machine, household cleaning machine, ultrasonic generator built machine.Features1. The ultrasonic generator can monitor the power system frequency ultrasound power.2. According to different requirements of users, real-time adjustment of various parameters, the power, amplitude, and running time.Circuit board and vibration head (ceramic transducer) Wiring instructions1. The board can not no-load …
AC 100W 40KHZ Ultrasonic Cleaning Power Driver Board with 50W 40K Transducer 220VRead More
5pcs 3S 18650 4A 11.1V BMS Li-ion Battery Protection Board 18650 Battery Charging Module Charger Electronic DIY
$19.48Battery Protection ModuleAdd to cartSpecificationsCharging Voltage:12.6V-13VOvercharge Voltage Range:4.25V-4.35V ± 0.05VOverpressure Voltage Range:2.3V-3.0V ± 0.05VUpper Limit Operating Current:3A-4AUpper Limit Instantaneous Current:9A-10AQuiescent Current:less than 30uAInternal Resistance:less than 100mohmEffective Life:more than 30,000 hoursOperating Temperature:-40- +50 degreesStorage Conditions:-40- +80 degreesSize:53 * 16 * 3mmShort Circuit Protection:protection, delay self-recovery ApplicationsThe power range is suitable for the following products:massager battery pack, LED light standby power …
3pcs infrared Light IR Camera Control Board for Surveillance Camera Night Vision CCTV Accessories
$10.52Driver ModuleAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.SpecificationsCurrent:700mAVoltage input:12V DCVoltage output:1.7-12V DCSize:38MM * 38MMPotential:good night vision effect; rigorous design, stable performance and strong anti-interference.Use:Suitable for all kinds of infrared lamp board drive, suitable for 1-6 infrared lampFunction:It can be …
Reviews
There are no reviews yet.