3Pcs J03 LED Digital Time Delay Relay DC 6-30V on off Trigger Delay Timming Timer Switch Micro USB Power Supply 5V 12V
$32.79
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Features
1. Wide voltage power supply (6 ~ 30V), supports microUSB 5.0V power supply, easy to use;
2. The interface is clear and simple, powerful, easy to understand, meet almost all your needs;
3. The emergency stop function (“STOP’key);With reverse polarity protection, reverse polarity will not burn the product.
4. Increase the sleep mode, if this mode is enabled, without any operation within 5 minutes, then automatically turn off the monitor, any key wake-up;
5. You can set a different OP, CL, LOP parameters, which are independent of each other, and are automatically saved;
6. After the module is powered down, all parameter settings are not lost.
Product parameters
1:Operating voltage:6–30V, support microUSB 5.0V power supply
2:Trigger Source:Active-high (3.0V-24V), have optocoupler isolation, can improve the system’s anti-jamming capability (customers can also shorting common ground).
3:Output capability:You can control the DC 30VDC 5A or 220VAC 5A device.
4:Quiescent Current:20mA; Operating Current:50mA
5:Life:more than 10 million times; Working temperature:-40→-85 →; Size:6.2*3.8*1.7cm.
6:With optocoupler isolation, enhanced anti-jamming capability, industrial grade board.
Special Note:The relay outputs are passive contact, just a switch.
Operating mode
P1:trigger signal, the relay is on ‘OP’ time, and then disconnect; in the ‘OP’ time, as follows
P1.1:signal is triggered again, invalid
P1.2:signal is triggered again, the clock is reset
P1.3:Signal trigger again, relay off, stop the clock;
P-2:trigger signal, the relay off ‘CL’ of time, the relay on ‘OP’ time, and then disconnect relay;
P3.1:trigger signal, the relay is turned on after the ‘OP’ time, the relay off ‘CL’ time, then the operation cycle, if the trigger signal period, the relay off, stop the clock; the number of cycles ( ‘LOP ‘) can be set.
P3.2:without triggering signal, the relay is on ‘OP’ time, the relay off ‘CL’ time, and has been cycling; frequency ( ‘LOP’) cycle can be set;
P-4:signal holding function. If there is a trigger signal timing is cleared, the relay remains on; when the signal disappears, after the timing ‘OP’ time, the relay is; if another signal during timing, timing is cleared.
Timing range
0.1 seconds (min) to 999 minutes (max) continuously adjustable
How to choose the time range
After setting the mode selection screen parameter value by a short press ‘STOP’ button to select the time range;
XXX. decimal point in the unit place, time range:1 second to 999 seconds.
XX. X decimal point in decade place, Timing range:0.1 seconds to 99.9 seconds
X. X. X. decimal full brightness, Timing range:1 minute to 999 minutes.
For example, you want to set ‘OP’ is 3.2 seconds, then move the decimal point to decade place, the digital display 03.2
Parameter description:’OP’ – conduction time, ‘CL’ – off time, ‘LOP’ – the number of cycles (1-999 times, ‘—‘ represents infinite loop).
These parameters are independent of each other, but is shared by each mode. For example, in P1.1 mode, set the on-time ‘OP’ is 5 seconds, if you switch to P1.2 mode, it’s ‘OP’ will be 5 seconds too.
In the main interface (display 000), short press ‘SET’ button will display ‘OP’ ( ‘CL’, ‘LOP’) and the corresponding time XXX;
Some parameters only mode ‘OP’ (such as the mode P1.1, P1.2, P1.3), short press the ‘SET’ key to display only the “OP” and the corresponding time;
Some models have parameters ‘OP’,’CL’, ‘LOP’ (such as the mode P3.1, P3.2), short press ‘SET’ button will display ‘OP’ and the corresponding time, “CL” and the corresponding time, “LOP” and the corresponding number of times;
In the main interface by short press ‘SET’ key to see information about the parameters of the current mode, very convenient!
How to set parameters
1. First, read the instructions to determine the required operating mode.
2. The module is powered up, the display at the current work mode (P1.1 default mode), then enter the main interface; press ‘SET’ button for 2 seconds after release to enter mode selection interface; a short time by pressing ‘UP’, ‘DOWN’ key to select the mode (P1.1 ~ P-4).
3. Select the mode (such as P3.2), short press the ‘SET’ button, then the parameter to be set flashes ( ‘OP’on-time, ‘CL’ off time, ‘LOP’ cycles ( ‘—‘ represents infinite loop)), by ‘UP’, ‘DOWN’ keys to adjust the parameter value, support long press (rapid increase or decrease) and short press (increase or decrease one unit); then short press the ‘STOP’ key to select the decimal point position, select the time range (0.1 seconds to 999 minutes); short press the ‘SET’ button to set the next parameters of the current mode of procedure is as above.
4. After the parameters are set, long press ‘SET’ button for 2 seconds then release, the name of the current mode will flash once, and then return to the main screen, set the parameters of success!
The main interface:In the relay does not work status display ‘000’ (no decimal point), with a decimal point under relay state.
Mode selection screen:Long press the ‘SET’ key to enter, after setting is completed, long press the ‘SET’ key to exit back to the main screen.
‘STOP’ button extensions
Relays enable mode
1. ON:Relay allows conduction in the ‘OP’ on-time;
2. OFF:relay prohibit conduction is always closed;
In the main interface, short press the ‘STOP’ button to switch between ON and OFF, the current in which the state will flash, and then return to the main screen. (This feature is an emergency stop function, click off the relay)
Sleep mode
1. ‘C-P’ Sleep mode:five minutes without any operation, the digital display automatically turns off, the program running as usual;
2. ‘O-d’ normal mode:digital display always open;
Press the ‘STOP’ button for two seconds and then release to switch ‘C-P’ and ‘O-d’ state, in which the current state of flashes and then return to the main screen.
Package Included
3 x DC 1 Channel Time Delay Relay Module
3 x Shell Case
Weight | 0.222 kg |
---|
Customers Also Viewed
JT-180 1.4W 7V Solar Panel Power Fountain Pump Outdoor Garden Pond Pool Submersible Water Pump Kit
$64.79Electrical Pump & ValveAdd to cartSpecificationsModel:JT-180Materail:Monocrystalline silicon+ABSSolar battery:7V,1.4WSolar battery:110mm*110mm/4.3inch*4.3inchThe power of pump:DC7V 1.4WMax flow pump:200L/hMax.water height of pump:75cm(Max,water-jet height:50cm)Life time:≥15000HoursFeatureThis product has the lowest rate of the power of solar battery to pump power,and it is not only very easy to operate the brushless motor under little sunshinelike the brush motor,but also, it has the much long life time than …
5pcs 220V XH-W3003 Micro Digital thermostat High Precision Temperature Control Switch Temperature Alarm
$68.61Sensor & Detector ModuleAdd to cartFeatureProduct Name:Microcomputer Temperature ControllerProduct model:XH-W3003Temperature range:-50~110°CTemperature control range:-50~110°CTemperature measurement accuracy:+-0.1 °CTemperature control accuracy:+-0.1 °CTemperature probe:1 meter waterproof probeSupply voltage:AC110-220VOutput power:AC220V:1000WOutput type:Direct outputOutput currentAppearance size:60 x 45 x 31mmOpening size:73mm (aperture 4mm)Features:Setting methodHigh temperature alarm (range:-50~110°C):For example, if you want to alarm when the temperature exceeds 20 °C, set the upper limit temperature to 20 °C …
30pcs 2.4G Wireless Remote Control Module Transmitter and Receiver Module Kit Transmission Reception Communication 6 Channel Output
$178.88Smart ModuleAdd to cartTY24D-TX is the transmitting module, TY24D-RX is the receiving module. The transmitting module only needs to provide 3.3V power supply and transmitting button and one LED as the transmitting status indication. The output port corresponding to the receiving module can output the level signal, and the module has the output status. Select to select the …
2Pcs DC-DC Boost Buck Adjustable Step Up Step Down Automatic Converter XL6009 Module Suitable for Solar Panel
$8.87Boost & Buck ModuleAdd to cartDescriptionsAuto start voltage will be pulled down to 7V or less, and engine will at high speed when the voltage up to 15V or higher. It is hard to work for 12V electrical equipment, this automatic buck boost module can solve this problem, regardless of the input voltage is 5V or 12V or 32V, the …
5 Pcs Blue Acrylic Wall Mounted Protective Case Support Cooling Fan for Raspberry Pi 4 Model B
$56.17Raspberry Pi & Orange PiAdd to cartDescription– Wall Mounting Available– Red Blue Black Optional– Support Adding Cooling Fan– Compatible With Raspberry Pi 4B– Make of Transparent Acrylic, could check the board status easilyThere is a Protective Film on the board surface, please take it off before using.Package Included5* Blue Acrylic Case Kit
5pcs 0.5A 3S Synchronous Buck Li-Ion Charger DC 5-23V to 4.2V 8.4V 12.6V Power Supply Module for 3.7V 7.4V 11.1V 18650 Lithium Battery
$32.85Power Supply ModuleAdd to cartDescription3-Cell(3S) 12.6V VersionInput voltage:DC 14.8-23V(Recommend DC 14.8V/15V/18V)Charging voltage:12.6VCharging current:0.5ALed indicatorBright:Charging Off:full blinking:almost full; If the charging current is too large (or the battery capacity is small), it will quickly enter the flashing state, and the charging current should be reduced.Operating ambient temperature:-40° to +85°Storage temperature:-65° to +125°Size:30*15*5.5mmWeight:2gApplicationsCellular TelephonesPDA, MP3 Players, MP4 PlayersDigital CamerasBluetooth ApplicationsGame PlayersNotebookli-on …
15W 18V Semi Flexible Solar Panel with 5V USB Port & Cables
$58.36Smart Robot & Solar PanelAdd to cartSpecificationsMaximum Power (Pmax):15wMaximum Power Voltage (Vmp):18VMaximum Power Current (Imp):1.2aThe Number of Cells:36 PCSOutput:USB 5V & DC 18VSize:435 * 200 * 2.5 mmFeaturesLightweight and easy to carry.The charging temperature is -20-70 degrees Celsius.Flexible solar panel, maximum bending 30 degrees arc.Short circuit and surge technology keeps you and your equipment safe.Durable, waterproof.Packing Included1 x solar panels1 x …
15W 18V Semi Flexible Solar Panel with 5V USB Port & CablesRead More
DPX6005S Digital CNC Adjustable DC Power Supply 0-60V/32V 5A/3A 48V24V12V Step-down Board with LCD Display
$82.94Power Supply ModuleAdd to cartFeaturesIt is a fully CNC programmable step-down power supply with small size, high power, high efficiency and stable operation. It adopts a 1.8-inch TFT color liquid crystal display to provide comprehensive and clear display data. The power supply is controlled by an advanced microprocessor and can be precisely adjusted. And display voltage and current; using …
Reviews
There are no reviews yet.