3Pcs J03 LED Digital Time Delay Relay DC 6-30V on off Trigger Delay Timming Timer Switch Micro USB Power Supply 5V 12V
$32.79
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Features
1. Wide voltage power supply (6 ~ 30V), supports microUSB 5.0V power supply, easy to use;
2. The interface is clear and simple, powerful, easy to understand, meet almost all your needs;
3. The emergency stop function (“STOP’key);With reverse polarity protection, reverse polarity will not burn the product.
4. Increase the sleep mode, if this mode is enabled, without any operation within 5 minutes, then automatically turn off the monitor, any key wake-up;
5. You can set a different OP, CL, LOP parameters, which are independent of each other, and are automatically saved;
6. After the module is powered down, all parameter settings are not lost.
Product parameters
1:Operating voltage:6–30V, support microUSB 5.0V power supply
2:Trigger Source:Active-high (3.0V-24V), have optocoupler isolation, can improve the system’s anti-jamming capability (customers can also shorting common ground).
3:Output capability:You can control the DC 30VDC 5A or 220VAC 5A device.
4:Quiescent Current:20mA; Operating Current:50mA
5:Life:more than 10 million times; Working temperature:-40→-85 →; Size:6.2*3.8*1.7cm.
6:With optocoupler isolation, enhanced anti-jamming capability, industrial grade board.
Special Note:The relay outputs are passive contact, just a switch.
Operating mode
P1:trigger signal, the relay is on ‘OP’ time, and then disconnect; in the ‘OP’ time, as follows
P1.1:signal is triggered again, invalid
P1.2:signal is triggered again, the clock is reset
P1.3:Signal trigger again, relay off, stop the clock;
P-2:trigger signal, the relay off ‘CL’ of time, the relay on ‘OP’ time, and then disconnect relay;
P3.1:trigger signal, the relay is turned on after the ‘OP’ time, the relay off ‘CL’ time, then the operation cycle, if the trigger signal period, the relay off, stop the clock; the number of cycles ( ‘LOP ‘) can be set.
P3.2:without triggering signal, the relay is on ‘OP’ time, the relay off ‘CL’ time, and has been cycling; frequency ( ‘LOP’) cycle can be set;
P-4:signal holding function. If there is a trigger signal timing is cleared, the relay remains on; when the signal disappears, after the timing ‘OP’ time, the relay is; if another signal during timing, timing is cleared.
Timing range
0.1 seconds (min) to 999 minutes (max) continuously adjustable
How to choose the time range
After setting the mode selection screen parameter value by a short press ‘STOP’ button to select the time range;
XXX. decimal point in the unit place, time range:1 second to 999 seconds.
XX. X decimal point in decade place, Timing range:0.1 seconds to 99.9 seconds
X. X. X. decimal full brightness, Timing range:1 minute to 999 minutes.
For example, you want to set ‘OP’ is 3.2 seconds, then move the decimal point to decade place, the digital display 03.2
Parameter description:’OP’ – conduction time, ‘CL’ – off time, ‘LOP’ – the number of cycles (1-999 times, ‘—‘ represents infinite loop).
These parameters are independent of each other, but is shared by each mode. For example, in P1.1 mode, set the on-time ‘OP’ is 5 seconds, if you switch to P1.2 mode, it’s ‘OP’ will be 5 seconds too.
In the main interface (display 000), short press ‘SET’ button will display ‘OP’ ( ‘CL’, ‘LOP’) and the corresponding time XXX;
Some parameters only mode ‘OP’ (such as the mode P1.1, P1.2, P1.3), short press the ‘SET’ key to display only the “OP” and the corresponding time;
Some models have parameters ‘OP’,’CL’, ‘LOP’ (such as the mode P3.1, P3.2), short press ‘SET’ button will display ‘OP’ and the corresponding time, “CL” and the corresponding time, “LOP” and the corresponding number of times;
In the main interface by short press ‘SET’ key to see information about the parameters of the current mode, very convenient!
How to set parameters
1. First, read the instructions to determine the required operating mode.
2. The module is powered up, the display at the current work mode (P1.1 default mode), then enter the main interface; press ‘SET’ button for 2 seconds after release to enter mode selection interface; a short time by pressing ‘UP’, ‘DOWN’ key to select the mode (P1.1 ~ P-4).
3. Select the mode (such as P3.2), short press the ‘SET’ button, then the parameter to be set flashes ( ‘OP’on-time, ‘CL’ off time, ‘LOP’ cycles ( ‘—‘ represents infinite loop)), by ‘UP’, ‘DOWN’ keys to adjust the parameter value, support long press (rapid increase or decrease) and short press (increase or decrease one unit); then short press the ‘STOP’ key to select the decimal point position, select the time range (0.1 seconds to 999 minutes); short press the ‘SET’ button to set the next parameters of the current mode of procedure is as above.
4. After the parameters are set, long press ‘SET’ button for 2 seconds then release, the name of the current mode will flash once, and then return to the main screen, set the parameters of success!
The main interface:In the relay does not work status display ‘000’ (no decimal point), with a decimal point under relay state.
Mode selection screen:Long press the ‘SET’ key to enter, after setting is completed, long press the ‘SET’ key to exit back to the main screen.
‘STOP’ button extensions
Relays enable mode
1. ON:Relay allows conduction in the ‘OP’ on-time;
2. OFF:relay prohibit conduction is always closed;
In the main interface, short press the ‘STOP’ button to switch between ON and OFF, the current in which the state will flash, and then return to the main screen. (This feature is an emergency stop function, click off the relay)
Sleep mode
1. ‘C-P’ Sleep mode:five minutes without any operation, the digital display automatically turns off, the program running as usual;
2. ‘O-d’ normal mode:digital display always open;
Press the ‘STOP’ button for two seconds and then release to switch ‘C-P’ and ‘O-d’ state, in which the current state of flashes and then return to the main screen.
Package Included
3 x DC 1 Channel Time Delay Relay Module
3 x Shell Case
Weight | 0.222 kg |
---|
Customers Also Viewed
380W 48V/60V Deep Well Pump 1.2m/h Stainless Steel Submersible Pump Deep for industrial Home Use
$226.79Electrical Pump & ValveAdd to cartFeatures– Pure copper motor– Stainless steel body– Safety insulation, strong power– High precision seal– Good mute effect– Suitable for using in ships, fishing boats, fish ponds, agricultural irrigation and etc.– This is a non-toxic, non-polluting, noiseless solar water pump– The pump has a built-in controller and is easy to install. It can connect the pump …
3Pcs PL2303TA USB To TTL RS232 Upgrade Module USB To Serial Port Download Cable
$16.52Electronic Accessories & SuppliesAdd to cart3Pcs PL2303TA USB To TTL RS232 Upgrade Module USB To Serial Port Download CableDescriptionThis is a new product design produced by PL2303TAChips. PL2303TA provides aRS232 like a full-duplex asynchronous serial devices to connect to any Universal Serial Bus (USB) Host to a convenient solution.PL2303TA perfectly compatible win XP/ VISTA / 7/8 / 8.1 System can …
3Pcs PL2303TA USB To TTL RS232 Upgrade Module USB To Serial Port Download CableRead More
3pcs Blue Silicone Protective Enclosure Cover for Motherboard Type A Cat Model
$13.92Other Module BoardAdd to cartProduct IntroductionThe cover case has dedicated holes position for corresponding function; do not affect the operation of micro:bit development board; do not affect the power access; do not affect the dot matrix display.The cute shape allows you to use micro:bit more fun.Size:58*47*12mmColor:BlueNote:The module board does not includes.Package includes3 x Silicone Protective Enclosure
2Pcs Left Type 36*19mm Silver Shock Absorption Wheels with M4 Screws for Smart Robot
$27.34Smart Robot & Solar PanelAdd to cartSpecifications– Wheel size:36*19mm– Color:Silver– Material:Aluminum Alloy– With bearing– Screw Nut Size:M4 Package Included2 x Silver Left Type Shock Absorption Wheel with Screws & Bearings
10pcs CJMCU-2662 LM2662 1.5-5.5V 400mA Negative Polarity inversion Capacitor Switch Board Negative Voltage Converter Power Supply Module
$36.32Sensor & Detector ModuleAdd to cartFeatures1. Polarity inversion module, for the same positive voltage into a negative voltage. To provide for the op amp negative supply and negative reference.Enter a positive voltage, a negative voltage output.2. Maximum current 200mA, enough to supply the op amp negative supply, negative reference and other needs.3. The charge pump circuit is simple, small size, …
250pcs Waterproof Soldering Ring Heat Shrinkable Medium Nozzle Terminal Solder Connectors
$36.44ConnectorsAdd to cartFeatures Simple one-step connection for wire, welding, insulation and sealing. Can be perfectly used in marine and automotive applications. The outside is a polyolefin tube and the inside is a hot melt adhesive. Welding and sealing and advanced waterproof function. Waterproof copper welding head can prevent wire corrosion. Polyolefin heat shrinkable butt connector can improve …
250pcs Waterproof Soldering Ring Heat Shrinkable Medium Nozzle Terminal Solder ConnectorsRead More
20pcs 16 Keys Capacitive Touch Key Pad Module RobotDyn for Arduino – products that work with official for Arduino boards
$163.70Sensor & Detector ModuleAdd to cartFeatureThis is a touch keypad function by measuring the capacitance of 16 electrode points.This compact inexpensive keypad can be connecting to any Capacitive module. In our catalog, you can find 16 Keys Capacitive touch modules which bases on TTP229 and connecting to the microcontroller with the I2C bus.This touch keypad is both an ideal learning …
Reviews
There are no reviews yet.