3Pcs J03 LED Digital Time Delay Relay DC 6-30V on off Trigger Delay Timming Timer Switch Micro USB Power Supply 5V 12V
$32.79
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Features
1. Wide voltage power supply (6 ~ 30V), supports microUSB 5.0V power supply, easy to use;
2. The interface is clear and simple, powerful, easy to understand, meet almost all your needs;
3. The emergency stop function (“STOP’key);With reverse polarity protection, reverse polarity will not burn the product.
4. Increase the sleep mode, if this mode is enabled, without any operation within 5 minutes, then automatically turn off the monitor, any key wake-up;
5. You can set a different OP, CL, LOP parameters, which are independent of each other, and are automatically saved;
6. After the module is powered down, all parameter settings are not lost.
Product parameters
1:Operating voltage:6–30V, support microUSB 5.0V power supply
2:Trigger Source:Active-high (3.0V-24V), have optocoupler isolation, can improve the system’s anti-jamming capability (customers can also shorting common ground).
3:Output capability:You can control the DC 30VDC 5A or 220VAC 5A device.
4:Quiescent Current:20mA; Operating Current:50mA
5:Life:more than 10 million times; Working temperature:-40→-85 →; Size:6.2*3.8*1.7cm.
6:With optocoupler isolation, enhanced anti-jamming capability, industrial grade board.
Special Note:The relay outputs are passive contact, just a switch.
Operating mode
P1:trigger signal, the relay is on ‘OP’ time, and then disconnect; in the ‘OP’ time, as follows
P1.1:signal is triggered again, invalid
P1.2:signal is triggered again, the clock is reset
P1.3:Signal trigger again, relay off, stop the clock;
P-2:trigger signal, the relay off ‘CL’ of time, the relay on ‘OP’ time, and then disconnect relay;
P3.1:trigger signal, the relay is turned on after the ‘OP’ time, the relay off ‘CL’ time, then the operation cycle, if the trigger signal period, the relay off, stop the clock; the number of cycles ( ‘LOP ‘) can be set.
P3.2:without triggering signal, the relay is on ‘OP’ time, the relay off ‘CL’ time, and has been cycling; frequency ( ‘LOP’) cycle can be set;
P-4:signal holding function. If there is a trigger signal timing is cleared, the relay remains on; when the signal disappears, after the timing ‘OP’ time, the relay is; if another signal during timing, timing is cleared.
Timing range
0.1 seconds (min) to 999 minutes (max) continuously adjustable
How to choose the time range
After setting the mode selection screen parameter value by a short press ‘STOP’ button to select the time range;
XXX. decimal point in the unit place, time range:1 second to 999 seconds.
XX. X decimal point in decade place, Timing range:0.1 seconds to 99.9 seconds
X. X. X. decimal full brightness, Timing range:1 minute to 999 minutes.
For example, you want to set ‘OP’ is 3.2 seconds, then move the decimal point to decade place, the digital display 03.2
Parameter description:’OP’ – conduction time, ‘CL’ – off time, ‘LOP’ – the number of cycles (1-999 times, ‘—‘ represents infinite loop).
These parameters are independent of each other, but is shared by each mode. For example, in P1.1 mode, set the on-time ‘OP’ is 5 seconds, if you switch to P1.2 mode, it’s ‘OP’ will be 5 seconds too.
In the main interface (display 000), short press ‘SET’ button will display ‘OP’ ( ‘CL’, ‘LOP’) and the corresponding time XXX;
Some parameters only mode ‘OP’ (such as the mode P1.1, P1.2, P1.3), short press the ‘SET’ key to display only the “OP” and the corresponding time;
Some models have parameters ‘OP’,’CL’, ‘LOP’ (such as the mode P3.1, P3.2), short press ‘SET’ button will display ‘OP’ and the corresponding time, “CL” and the corresponding time, “LOP” and the corresponding number of times;
In the main interface by short press ‘SET’ key to see information about the parameters of the current mode, very convenient!
How to set parameters
1. First, read the instructions to determine the required operating mode.
2. The module is powered up, the display at the current work mode (P1.1 default mode), then enter the main interface; press ‘SET’ button for 2 seconds after release to enter mode selection interface; a short time by pressing ‘UP’, ‘DOWN’ key to select the mode (P1.1 ~ P-4).
3. Select the mode (such as P3.2), short press the ‘SET’ button, then the parameter to be set flashes ( ‘OP’on-time, ‘CL’ off time, ‘LOP’ cycles ( ‘—‘ represents infinite loop)), by ‘UP’, ‘DOWN’ keys to adjust the parameter value, support long press (rapid increase or decrease) and short press (increase or decrease one unit); then short press the ‘STOP’ key to select the decimal point position, select the time range (0.1 seconds to 999 minutes); short press the ‘SET’ button to set the next parameters of the current mode of procedure is as above.
4. After the parameters are set, long press ‘SET’ button for 2 seconds then release, the name of the current mode will flash once, and then return to the main screen, set the parameters of success!
The main interface:In the relay does not work status display ‘000’ (no decimal point), with a decimal point under relay state.
Mode selection screen:Long press the ‘SET’ key to enter, after setting is completed, long press the ‘SET’ key to exit back to the main screen.
‘STOP’ button extensions
Relays enable mode
1. ON:Relay allows conduction in the ‘OP’ on-time;
2. OFF:relay prohibit conduction is always closed;
In the main interface, short press the ‘STOP’ button to switch between ON and OFF, the current in which the state will flash, and then return to the main screen. (This feature is an emergency stop function, click off the relay)
Sleep mode
1. ‘C-P’ Sleep mode:five minutes without any operation, the digital display automatically turns off, the program running as usual;
2. ‘O-d’ normal mode:digital display always open;
Press the ‘STOP’ button for two seconds and then release to switch ‘C-P’ and ‘O-d’ state, in which the current state of flashes and then return to the main screen.
Package Included
3 x DC 1 Channel Time Delay Relay Module
3 x Shell Case
Weight | 0.222 kg |
---|
Customers Also Viewed
WEAH-307 3 Way Audio Speaker Crossover 100W Filter Treble Mediant Bass Frequency Divider Module
$15.30Amplifier BoardAdd to cartFeatureMode:WEAH-307Power:100WImpedance:4-8ohmCompatible for:Under 6inches HornTreble Standard:12db/octBass Standard:12db/octSize:8.5×6.2×2.6cmFrequency response:low 45Hz, high 20KHzPackage includes1 x 100W Filter Treble Mediant Bass Frequency Divider
3pcs WXD3-13-2W Precision Potentiometer 22K 22K Ohm Wirewound Multi-Turn Potentiometer
$10.49Module ComponentsAdd to cartSpecificationsResistance range:22K┯Resistance tolerance:÷ 5%Rotation angle:3600 ÷ 20 Number of laps:10 lapsRated voltage:160VStarting torque:3.5 ~ 100mN.mRated power:2W (85 →) 0W (125 →)Linearity accuracy:÷ 0.3%Mechanical durability:10,000 weeksPackage included3 x Potentiometer
20Pcs Serial Port WIFI ESP8266 Module Adapter Plate with IO Lead Out for ESP-07 ESP-08 ESP-12
$12.02Smart ModuleAdd to cart20Pcs Serial Port WIFI ESP8266 Module Adapter Plate With IO Lead Out For ESP-07 ESP-08 ESP-12This Adapter Plate is for ESP-07 ESP-08 ESP-12, a test board with IO lead out.NoteNeed to solder 3V regulator by youself.ESP-07, ESP-08, ESP-12 module board are not included!!!Package included20 x Serial Port WIFI ESP8266 Module Adapter Plate40 x Pins
10pcs 2S 5A Li-ion Lithium Battery 7.4V 8.4V 18650 Charger Protection Board BMS for Li-ion Lipo Battery
$16.88Battery Protection ModuleAdd to cartSpecificationsModel:HX-2S-A2 Overcharge voltage range:4.25-4.35v ± 0.05vSize:17.5 * 17.5 * 3.2mm over discharge voltage range:2.5-3.0v ± 0.05vUpper limit operating current:5A Operating temperature:-40 — +50 °Upper limit instantaneous current:7A Storage conditions:-40– +80 °Quiescent current:less than 10uA Effective life:more than 50,000 hoursInternal resistance:less than 300mΩ Short circuit protection:can be protected, need to charge recoveryCharging voltage:8.4V-9VWelding point DescriptionB + …
DC 24V 600L/H Submersible Pump Immersible Pump Under Water Pump Bath Pump
$42.51Electrical Pump & ValveAdd to cartSubmersible Pump Immersible Pump Under Water Aquarium Bath Pump DC 24V 600L/HSpecificationColor:GreyUse:SubmersibleMaterial:Engineering ABSRated Voltage:DC 24VStarting Voltage:6VCurrent:0.75AFlow:600L/HNoise:50dB MAXMax. Head:500cmPower:18wWaterproof grade:IP68Motor:brush motorWater temperature:-20 ° C ~ 60 ° ° CAmbient humidity:45%~90%No load current:less than 0.2ACurrent at load:1.2ACable:1.5m /59.06inch(appr.)Total Length:105.9mm /4.31inch(appr.)FeaturesBrand New and high quality.Suitable for tap water, sea water, ground waterCannot be used directly with 220V AC …
DC 24V 600L/H Submersible Pump Immersible Pump Under Water Pump Bath PumpRead More
TDA7498 2.1 Digital Power Amplifier Board 200W+100W+100W Supasses TPA3116 Class D DC24V
$70.06Amplifier BoardAdd to cartFeatures-Using original TDA7498 TL072-The front input capacitor and the inter-stage coupling capacitor use Siemens’ top-level capacitors 1UF, the electrolytic capacitor signal main circuit uses Taiwanese famous brands, and the main filter capacitor uses special electrolytic capacitors 2≠2200UF to ensure strong continuous power support.-The resistors are high-precision chip resistors, and the main circuit uses five-ring metal …
TDA7498 2.1 Digital Power Amplifier Board 200W+100W+100W Supasses TPA3116 Class D DC24VRead More
3Pcs RobotDyn RTC DS1307 Real Time Clock Battery Shield with Pin Headers Set
$18.67Expansion Board & ShieldAdd to cartPINOUT:http://img.staticbg.com/file/products/20171226001032PINOUT-RTCDS1307.pdfSchematic:http://img.staticbg.com/file/products/20171226001140Schematic-RTCDS1307.pdfFeatureType:Logic ICsPackage includes3 x RTC DS1307 (real time clock) + battery3 x Wemos D1 mini shield6 x Male Pin Header 8pins6 x Female Pin Header -BLACK 8pins6 x Stackable Header – BLACK 8pins
Reviews
There are no reviews yet.