3Pcs J03 LED Digital Time Delay Relay DC 6-30V on off Trigger Delay Timming Timer Switch Micro USB Power Supply 5V 12V
$32.79
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Features
1. Wide voltage power supply (6 ~ 30V), supports microUSB 5.0V power supply, easy to use;
2. The interface is clear and simple, powerful, easy to understand, meet almost all your needs;
3. The emergency stop function (“STOP’key);With reverse polarity protection, reverse polarity will not burn the product.
4. Increase the sleep mode, if this mode is enabled, without any operation within 5 minutes, then automatically turn off the monitor, any key wake-up;
5. You can set a different OP, CL, LOP parameters, which are independent of each other, and are automatically saved;
6. After the module is powered down, all parameter settings are not lost.
Product parameters
1:Operating voltage:6–30V, support microUSB 5.0V power supply
2:Trigger Source:Active-high (3.0V-24V), have optocoupler isolation, can improve the system’s anti-jamming capability (customers can also shorting common ground).
3:Output capability:You can control the DC 30VDC 5A or 220VAC 5A device.
4:Quiescent Current:20mA; Operating Current:50mA
5:Life:more than 10 million times; Working temperature:-40→-85 →; Size:6.2*3.8*1.7cm.
6:With optocoupler isolation, enhanced anti-jamming capability, industrial grade board.
Special Note:The relay outputs are passive contact, just a switch.
Operating mode
P1:trigger signal, the relay is on ‘OP’ time, and then disconnect; in the ‘OP’ time, as follows
P1.1:signal is triggered again, invalid
P1.2:signal is triggered again, the clock is reset
P1.3:Signal trigger again, relay off, stop the clock;
P-2:trigger signal, the relay off ‘CL’ of time, the relay on ‘OP’ time, and then disconnect relay;
P3.1:trigger signal, the relay is turned on after the ‘OP’ time, the relay off ‘CL’ time, then the operation cycle, if the trigger signal period, the relay off, stop the clock; the number of cycles ( ‘LOP ‘) can be set.
P3.2:without triggering signal, the relay is on ‘OP’ time, the relay off ‘CL’ time, and has been cycling; frequency ( ‘LOP’) cycle can be set;
P-4:signal holding function. If there is a trigger signal timing is cleared, the relay remains on; when the signal disappears, after the timing ‘OP’ time, the relay is; if another signal during timing, timing is cleared.
Timing range
0.1 seconds (min) to 999 minutes (max) continuously adjustable
How to choose the time range
After setting the mode selection screen parameter value by a short press ‘STOP’ button to select the time range;
XXX. decimal point in the unit place, time range:1 second to 999 seconds.
XX. X decimal point in decade place, Timing range:0.1 seconds to 99.9 seconds
X. X. X. decimal full brightness, Timing range:1 minute to 999 minutes.
For example, you want to set ‘OP’ is 3.2 seconds, then move the decimal point to decade place, the digital display 03.2
Parameter description:’OP’ – conduction time, ‘CL’ – off time, ‘LOP’ – the number of cycles (1-999 times, ‘—‘ represents infinite loop).
These parameters are independent of each other, but is shared by each mode. For example, in P1.1 mode, set the on-time ‘OP’ is 5 seconds, if you switch to P1.2 mode, it’s ‘OP’ will be 5 seconds too.
In the main interface (display 000), short press ‘SET’ button will display ‘OP’ ( ‘CL’, ‘LOP’) and the corresponding time XXX;
Some parameters only mode ‘OP’ (such as the mode P1.1, P1.2, P1.3), short press the ‘SET’ key to display only the “OP” and the corresponding time;
Some models have parameters ‘OP’,’CL’, ‘LOP’ (such as the mode P3.1, P3.2), short press ‘SET’ button will display ‘OP’ and the corresponding time, “CL” and the corresponding time, “LOP” and the corresponding number of times;
In the main interface by short press ‘SET’ key to see information about the parameters of the current mode, very convenient!
How to set parameters
1. First, read the instructions to determine the required operating mode.
2. The module is powered up, the display at the current work mode (P1.1 default mode), then enter the main interface; press ‘SET’ button for 2 seconds after release to enter mode selection interface; a short time by pressing ‘UP’, ‘DOWN’ key to select the mode (P1.1 ~ P-4).
3. Select the mode (such as P3.2), short press the ‘SET’ button, then the parameter to be set flashes ( ‘OP’on-time, ‘CL’ off time, ‘LOP’ cycles ( ‘—‘ represents infinite loop)), by ‘UP’, ‘DOWN’ keys to adjust the parameter value, support long press (rapid increase or decrease) and short press (increase or decrease one unit); then short press the ‘STOP’ key to select the decimal point position, select the time range (0.1 seconds to 999 minutes); short press the ‘SET’ button to set the next parameters of the current mode of procedure is as above.
4. After the parameters are set, long press ‘SET’ button for 2 seconds then release, the name of the current mode will flash once, and then return to the main screen, set the parameters of success!
The main interface:In the relay does not work status display ‘000’ (no decimal point), with a decimal point under relay state.
Mode selection screen:Long press the ‘SET’ key to enter, after setting is completed, long press the ‘SET’ key to exit back to the main screen.
‘STOP’ button extensions
Relays enable mode
1. ON:Relay allows conduction in the ‘OP’ on-time;
2. OFF:relay prohibit conduction is always closed;
In the main interface, short press the ‘STOP’ button to switch between ON and OFF, the current in which the state will flash, and then return to the main screen. (This feature is an emergency stop function, click off the relay)
Sleep mode
1. ‘C-P’ Sleep mode:five minutes without any operation, the digital display automatically turns off, the program running as usual;
2. ‘O-d’ normal mode:digital display always open;
Press the ‘STOP’ button for two seconds and then release to switch ‘C-P’ and ‘O-d’ state, in which the current state of flashes and then return to the main screen.
Package Included
3 x DC 1 Channel Time Delay Relay Module
3 x Shell Case
Weight | 0.222 kg |
---|
Customers Also Viewed
BESTEP 4 Channel 24V Relay Module High And Low Level Trigger for
$10.15Relay ModuleAdd to cartDescription Maximum load:AC 250V/10A, DC 30V/10A. The chip optocoupler isolation, strong driving ability, stable performance, trigger current 5mA. Working voltage is 24V. Every channel of the module can be set up by high jumper or low level trigger. Fault tolerant design, even if the control line is broken, the relay will not act. Power indicator …
BESTEP 4 Channel 24V Relay Module High And Low Level Trigger forRead More
5Pcs CJMCU-3386 MC33186DH1 Automotive Computer Board Idle Speed Throttle Drive Board A H Bridge
$50.91Other Module BoardAdd to cartDescriptionThe 33886 is a monolithic H-Bridge ideal for fractional horsepowerDC-motor and bi-directional thrust solenoid control. The IC incorporatesinternal control logic, charge pump, gate drive, and low RDS(ON) MOSFEToutput circuitry. The 33886 is able to control continuous inductive DC loadcurrents up to 5.0 A. Output loads can be pulse width modulated (PWM-ed)at frequencies up to 10 …
20pcs Light Dependent Resistor LDR 5MM Photoresistor Photoelectric Switch Element Photo Detector 5516
$4.36Module ComponentsAdd to cartSpecificationsModel:5549Voltage(VDC):150Power Consumption(mw):100Ambient Temperature(C):-30~+70Spectral Peak(nm):540Bright Resistance(10Lux)K┯:5-10Response Time(MS):Rise:20 Decline:30Package included20 x Resistor
PWM 20A 12V/24V Auto Solar Panel Solar Charge Controller Battery Charge Adapter LCD USB
$36.44Solar ControllersAdd to cartSpecificationsName:20A 12V/24V LCD Display PWM Solar Panel Charge ControllerModel:C11465Rated voltage:12/24V AUTOCharge current:20ADischarge current:10AMax.PV input power:260W(12V),520W(24V)Max solar input12V battery,the highest 23V24V battery when the highest 46VEqualization:14.2VFloat charge:13.7V (defaul,adjustable)Discharge stop:10.7V(defaul,adjustable)Discharge reconnect:12.6V(defaul,adjustable)Charge reconnect:13VVoltage of open light:Solar panel 8V(Light lights delay)Voltage of close light:Solar panel 8V(Light off delay)USB output:2 way USB output,5V/2A(Max.)Self-consumeOperationg temperature:-35-60℃Color:BlackSize:133.5mmx70mmx35mmFeatureBuild-in industrial micro controller.Big LCD display,all adjustable …
PWM 20A 12V/24V Auto Solar Panel Solar Charge Controller Battery Charge Adapter LCD USBRead More
Waveshare Sensor Expansion Board Supports XBEE Module Compatible for Arduino
$39.35Expansion Board & ShieldAdd to cartDocumentsSchematic:Click here to openSample tutorial:Click here to openWhat do I mainly doArduino is a huge ecosystem. If the Pi interface can be converted to the Arduino standard, it can be connected to a variety of compatible Arduino expansion boards and connected to the Arduino ecosystem to obtain more available resources.I just do this.Basic situationCompatible with …
Waveshare Sensor Expansion Board Supports XBEE Module Compatible for ArduinoRead More
Emakefun DC5V RGB Tricolor Lamp Module 5PIN Anti-reverse Connector Compatible with Lego Jack Fixing
$10.61Sensor & Detector ModuleAdd to cartFeature1. Supply voltage:5V2. Connection method:5PIN anti-reverse connection Dupont line3. Module size:40*22.5mm4. Installation method:M4 screw compatible with Lego jack fixing5. Connection port:PH2.0Package includes1 x RGB Tricolor Lamp Module (the other items are not includes)
Reviews
There are no reviews yet.