3Pcs J03 LED Digital Time Delay Relay DC 6-30V on off Trigger Delay Timming Timer Switch Micro USB Power Supply 5V 12V
$32.79
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Features
1. Wide voltage power supply (6 ~ 30V), supports microUSB 5.0V power supply, easy to use;
2. The interface is clear and simple, powerful, easy to understand, meet almost all your needs;
3. The emergency stop function (“STOP’key);With reverse polarity protection, reverse polarity will not burn the product.
4. Increase the sleep mode, if this mode is enabled, without any operation within 5 minutes, then automatically turn off the monitor, any key wake-up;
5. You can set a different OP, CL, LOP parameters, which are independent of each other, and are automatically saved;
6. After the module is powered down, all parameter settings are not lost.
Product parameters
1:Operating voltage:6–30V, support microUSB 5.0V power supply
2:Trigger Source:Active-high (3.0V-24V), have optocoupler isolation, can improve the system’s anti-jamming capability (customers can also shorting common ground).
3:Output capability:You can control the DC 30VDC 5A or 220VAC 5A device.
4:Quiescent Current:20mA; Operating Current:50mA
5:Life:more than 10 million times; Working temperature:-40→-85 →; Size:6.2*3.8*1.7cm.
6:With optocoupler isolation, enhanced anti-jamming capability, industrial grade board.
Special Note:The relay outputs are passive contact, just a switch.
Operating mode
P1:trigger signal, the relay is on ‘OP’ time, and then disconnect; in the ‘OP’ time, as follows
P1.1:signal is triggered again, invalid
P1.2:signal is triggered again, the clock is reset
P1.3:Signal trigger again, relay off, stop the clock;
P-2:trigger signal, the relay off ‘CL’ of time, the relay on ‘OP’ time, and then disconnect relay;
P3.1:trigger signal, the relay is turned on after the ‘OP’ time, the relay off ‘CL’ time, then the operation cycle, if the trigger signal period, the relay off, stop the clock; the number of cycles ( ‘LOP ‘) can be set.
P3.2:without triggering signal, the relay is on ‘OP’ time, the relay off ‘CL’ time, and has been cycling; frequency ( ‘LOP’) cycle can be set;
P-4:signal holding function. If there is a trigger signal timing is cleared, the relay remains on; when the signal disappears, after the timing ‘OP’ time, the relay is; if another signal during timing, timing is cleared.
Timing range
0.1 seconds (min) to 999 minutes (max) continuously adjustable
How to choose the time range
After setting the mode selection screen parameter value by a short press ‘STOP’ button to select the time range;
XXX. decimal point in the unit place, time range:1 second to 999 seconds.
XX. X decimal point in decade place, Timing range:0.1 seconds to 99.9 seconds
X. X. X. decimal full brightness, Timing range:1 minute to 999 minutes.
For example, you want to set ‘OP’ is 3.2 seconds, then move the decimal point to decade place, the digital display 03.2
Parameter description:’OP’ – conduction time, ‘CL’ – off time, ‘LOP’ – the number of cycles (1-999 times, ‘—‘ represents infinite loop).
These parameters are independent of each other, but is shared by each mode. For example, in P1.1 mode, set the on-time ‘OP’ is 5 seconds, if you switch to P1.2 mode, it’s ‘OP’ will be 5 seconds too.
In the main interface (display 000), short press ‘SET’ button will display ‘OP’ ( ‘CL’, ‘LOP’) and the corresponding time XXX;
Some parameters only mode ‘OP’ (such as the mode P1.1, P1.2, P1.3), short press the ‘SET’ key to display only the “OP” and the corresponding time;
Some models have parameters ‘OP’,’CL’, ‘LOP’ (such as the mode P3.1, P3.2), short press ‘SET’ button will display ‘OP’ and the corresponding time, “CL” and the corresponding time, “LOP” and the corresponding number of times;
In the main interface by short press ‘SET’ key to see information about the parameters of the current mode, very convenient!
How to set parameters
1. First, read the instructions to determine the required operating mode.
2. The module is powered up, the display at the current work mode (P1.1 default mode), then enter the main interface; press ‘SET’ button for 2 seconds after release to enter mode selection interface; a short time by pressing ‘UP’, ‘DOWN’ key to select the mode (P1.1 ~ P-4).
3. Select the mode (such as P3.2), short press the ‘SET’ button, then the parameter to be set flashes ( ‘OP’on-time, ‘CL’ off time, ‘LOP’ cycles ( ‘—‘ represents infinite loop)), by ‘UP’, ‘DOWN’ keys to adjust the parameter value, support long press (rapid increase or decrease) and short press (increase or decrease one unit); then short press the ‘STOP’ key to select the decimal point position, select the time range (0.1 seconds to 999 minutes); short press the ‘SET’ button to set the next parameters of the current mode of procedure is as above.
4. After the parameters are set, long press ‘SET’ button for 2 seconds then release, the name of the current mode will flash once, and then return to the main screen, set the parameters of success!
The main interface:In the relay does not work status display ‘000’ (no decimal point), with a decimal point under relay state.
Mode selection screen:Long press the ‘SET’ key to enter, after setting is completed, long press the ‘SET’ key to exit back to the main screen.
‘STOP’ button extensions
Relays enable mode
1. ON:Relay allows conduction in the ‘OP’ on-time;
2. OFF:relay prohibit conduction is always closed;
In the main interface, short press the ‘STOP’ button to switch between ON and OFF, the current in which the state will flash, and then return to the main screen. (This feature is an emergency stop function, click off the relay)
Sleep mode
1. ‘C-P’ Sleep mode:five minutes without any operation, the digital display automatically turns off, the program running as usual;
2. ‘O-d’ normal mode:digital display always open;
Press the ‘STOP’ button for two seconds and then release to switch ‘C-P’ and ‘O-d’ state, in which the current state of flashes and then return to the main screen.
Package Included
3 x DC 1 Channel Time Delay Relay Module
3 x Shell Case
Weight | 0.222 kg |
---|
Customers Also Viewed
5pcs Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology Small Production Kit
$16.60DIY Electronic KitsAdd to cartDescriptionThe purpose of the experiment1. Understand and recognize the light-emitting diodes and illuminate the light-emitting diodes (LEDs);2. Understand the role of understanding resistance, series and parallel resistance;3. Understand the self-locking switch;4. Understand and recognize adjustable resistors and use adjustable resistors;Experimental stepsStep 1:The long leg of the light-emitting diode (LED) is the positive pole, and the …
50pcs Universal PCB Board 7x9cm 2.54mm Hole Pitch DIY Prototype Paper Printed Circuit Board Panel Single Sided Board
$32.93Electronic Accessories & SuppliesAdd to cartFeaturesPremium one side prototype PCB printed circuit board, universal strip breadboard.All holes are plated through, smooth and clear.Sturdy and easy to use, the plated holes are very solid which makes it very easy to solder components on and they can hold up well and handle reasonable heat levels and dwell times.A good assortment of quality …
50mm Submersible Bore 0.5 HP Water Farm Garden Deep Well Pump 220V 180ft 8GPM
$340.19Electrical Pump & ValveAdd to cartFeatures-2inch deep well submersible pump, fits in the 2inch well casing.-Patented impeller design provides extended pump life and heavy flow under the severe circumstances.-This pump has a much longer pump life than the all-plastic-bottom-suction pump.-Solid 304 stainless steel body with heavy duty cast iron discharge.-Industrial grade heavy duty, also good for home usage.-Built in 1/2 …
50mm Submersible Bore 0.5 HP Water Farm Garden Deep Well Pump 220V 180ft 8GPMRead More
1Hz-150Khz 3.3V-30V Signal Generator PWM Pulse Frequency Duty Cycle Adjustable Module LCD Display
$22.06Other Module BoardAdd to cartParameter settingsThe module has four independent keys, used to set the frequency and duty cycle, support short press (increase or decrease a unit)and long press (fast increase or decrease), very simple, set the parameters automatically save, power failure Lost.Module parameters1. Working voltage:3.3 ~ 30V;2. Frequency range:1Hz ~ 150KHz;3. Frequency accuracy:the accuracy in each range is …
5pcs LCD1602 LCD Shell for 1602 Blue/Yellow And I2C 1602 Blue/Yellow Green Backlight LCD Module Case
$17.73Electronic Accessories & SuppliesAdd to cartDescription Screen size:2.5 inches Material:acrylic Application 1602 Blue Backlight LCD Display Module:https://www.hobbyant.com/1Pc-1602-Character-LCD-Display-Module-Blue-Backlight-p-978160.htmlrmmds=search 1602 Yellow Backlight LCD Display Module:https://www.hobbyant.com/1Pc-1602-Character-LCD-Display-Module-Yellow-Backlight-For–p-978155.htmlrmmds=search I2C 1602 Blue Backlight LCD Display Module:https://www.hobbyant.com/IIC-I2C-1602-Blue-Backlight-LCD-Display-Module-For–p-950726.htmlrmmds=search I2C 1602 Yellow Green Backlight LCD Display Module:https://www.hobbyant.com/IICI2C-1602-Yellow-Green-Backlight-LCD-Display-Module-For–p-950728.htmlrmmds=search Package included 5 x LCD1602 LCD shell
Reviews
There are no reviews yet.