3Pcs J03 LED Digital Time Delay Relay DC 6-30V on off Trigger Delay Timming Timer Switch Micro USB Power Supply 5V 12V
$32.79
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Features
1. Wide voltage power supply (6 ~ 30V), supports microUSB 5.0V power supply, easy to use;
2. The interface is clear and simple, powerful, easy to understand, meet almost all your needs;
3. The emergency stop function (“STOP’key);With reverse polarity protection, reverse polarity will not burn the product.
4. Increase the sleep mode, if this mode is enabled, without any operation within 5 minutes, then automatically turn off the monitor, any key wake-up;
5. You can set a different OP, CL, LOP parameters, which are independent of each other, and are automatically saved;
6. After the module is powered down, all parameter settings are not lost.
Product parameters
1:Operating voltage:6–30V, support microUSB 5.0V power supply
2:Trigger Source:Active-high (3.0V-24V), have optocoupler isolation, can improve the system’s anti-jamming capability (customers can also shorting common ground).
3:Output capability:You can control the DC 30VDC 5A or 220VAC 5A device.
4:Quiescent Current:20mA; Operating Current:50mA
5:Life:more than 10 million times; Working temperature:-40→-85 →; Size:6.2*3.8*1.7cm.
6:With optocoupler isolation, enhanced anti-jamming capability, industrial grade board.
Special Note:The relay outputs are passive contact, just a switch.
Operating mode
P1:trigger signal, the relay is on ‘OP’ time, and then disconnect; in the ‘OP’ time, as follows
P1.1:signal is triggered again, invalid
P1.2:signal is triggered again, the clock is reset
P1.3:Signal trigger again, relay off, stop the clock;
P-2:trigger signal, the relay off ‘CL’ of time, the relay on ‘OP’ time, and then disconnect relay;
P3.1:trigger signal, the relay is turned on after the ‘OP’ time, the relay off ‘CL’ time, then the operation cycle, if the trigger signal period, the relay off, stop the clock; the number of cycles ( ‘LOP ‘) can be set.
P3.2:without triggering signal, the relay is on ‘OP’ time, the relay off ‘CL’ time, and has been cycling; frequency ( ‘LOP’) cycle can be set;
P-4:signal holding function. If there is a trigger signal timing is cleared, the relay remains on; when the signal disappears, after the timing ‘OP’ time, the relay is; if another signal during timing, timing is cleared.
Timing range
0.1 seconds (min) to 999 minutes (max) continuously adjustable
How to choose the time range
After setting the mode selection screen parameter value by a short press ‘STOP’ button to select the time range;
XXX. decimal point in the unit place, time range:1 second to 999 seconds.
XX. X decimal point in decade place, Timing range:0.1 seconds to 99.9 seconds
X. X. X. decimal full brightness, Timing range:1 minute to 999 minutes.
For example, you want to set ‘OP’ is 3.2 seconds, then move the decimal point to decade place, the digital display 03.2
Parameter description:’OP’ – conduction time, ‘CL’ – off time, ‘LOP’ – the number of cycles (1-999 times, ‘—‘ represents infinite loop).
These parameters are independent of each other, but is shared by each mode. For example, in P1.1 mode, set the on-time ‘OP’ is 5 seconds, if you switch to P1.2 mode, it’s ‘OP’ will be 5 seconds too.
In the main interface (display 000), short press ‘SET’ button will display ‘OP’ ( ‘CL’, ‘LOP’) and the corresponding time XXX;
Some parameters only mode ‘OP’ (such as the mode P1.1, P1.2, P1.3), short press the ‘SET’ key to display only the “OP” and the corresponding time;
Some models have parameters ‘OP’,’CL’, ‘LOP’ (such as the mode P3.1, P3.2), short press ‘SET’ button will display ‘OP’ and the corresponding time, “CL” and the corresponding time, “LOP” and the corresponding number of times;
In the main interface by short press ‘SET’ key to see information about the parameters of the current mode, very convenient!
How to set parameters
1. First, read the instructions to determine the required operating mode.
2. The module is powered up, the display at the current work mode (P1.1 default mode), then enter the main interface; press ‘SET’ button for 2 seconds after release to enter mode selection interface; a short time by pressing ‘UP’, ‘DOWN’ key to select the mode (P1.1 ~ P-4).
3. Select the mode (such as P3.2), short press the ‘SET’ button, then the parameter to be set flashes ( ‘OP’on-time, ‘CL’ off time, ‘LOP’ cycles ( ‘—‘ represents infinite loop)), by ‘UP’, ‘DOWN’ keys to adjust the parameter value, support long press (rapid increase or decrease) and short press (increase or decrease one unit); then short press the ‘STOP’ key to select the decimal point position, select the time range (0.1 seconds to 999 minutes); short press the ‘SET’ button to set the next parameters of the current mode of procedure is as above.
4. After the parameters are set, long press ‘SET’ button for 2 seconds then release, the name of the current mode will flash once, and then return to the main screen, set the parameters of success!
The main interface:In the relay does not work status display ‘000’ (no decimal point), with a decimal point under relay state.
Mode selection screen:Long press the ‘SET’ key to enter, after setting is completed, long press the ‘SET’ key to exit back to the main screen.
‘STOP’ button extensions
Relays enable mode
1. ON:Relay allows conduction in the ‘OP’ on-time;
2. OFF:relay prohibit conduction is always closed;
In the main interface, short press the ‘STOP’ button to switch between ON and OFF, the current in which the state will flash, and then return to the main screen. (This feature is an emergency stop function, click off the relay)
Sleep mode
1. ‘C-P’ Sleep mode:five minutes without any operation, the digital display automatically turns off, the program running as usual;
2. ‘O-d’ normal mode:digital display always open;
Press the ‘STOP’ button for two seconds and then release to switch ‘C-P’ and ‘O-d’ state, in which the current state of flashes and then return to the main screen.
Package Included
3 x DC 1 Channel Time Delay Relay Module
3 x Shell Case
Weight | 0.222 kg |
---|
Customers Also Viewed
Ebyte E810-DTU(CAN-ETH) Smart Protocol Conversion GPRS Modem Modbus to TCP/IP CAN Bus Ethernet interface Modbus RTU Gateway
$96.54Smart ModuleAdd to cartSpecificationItemsDescriptionInterfaceEthernet:RJ45, 10/100MbpsCAN:1*5*3.81, ScrewingNetwork protocolIP,TCP/UDP, ARP, ICMP, IPV4Simple transparent transmissionTCP Server,TCP Client,UDP Server,UDP Client,Cloud transparent transmissionData Packing MechanismByte packing and time packingTCP Server connectionSupporting up to 6 TCP connectionsIP accessStatic IP,DHCPDNSSupportCAN Transmit baud rateA total of 15 baud rates from 6Kbps-1000KbpsCAN filtering modeUp to 8 filtration modesCAN data layoutProtocol formatParameter configurationWeb page configurationWorking current82mA@12VVoltage8V~28VDC,Over 28V may …
TP4056 Micro USB 5V 1A Lithium Battery Charging Protection Board TE585 Lipo Charger Module
$4.36Battery Protection ModuleAdd to cartSpecificationProduct name:Lithium Battery Charging BoardInput voltage:5VMaximum charging current:1000 mACharge cut-off voltage:4.2 V + / – 1%Battery overcharge protection voltage:2.5 VBattery over-current protection current:3 AInput interface:micro USBSize:27mm x 17mmHow to Use1. Input port with micro 5pin USB female, can directly use mobile charger for input to the lithium battery,and still retain the input voltage wiring solder …
TP4056 Micro USB 5V 1A Lithium Battery Charging Protection Board TE585 Lipo Charger ModuleRead More
10pcs 10-50W 15Wx2 Audio Power Amplifier DC 6 -18V TDA7297 Module Double Channel
$77.83Amplifier BoardAdd to cartFeatures– Working Voltage:6-18V DC– The onboard TDA7297 audio power amplifier chip, double channel 15WX15W– Speaker for European 4-8 10-50W use– Main pin has led chip, convenient external control device, the onboard– 5.08 (mm) distance between two p terminal 2 road, around a track connection output respectively– The onboard dial potentiometer, output size can adjust the …
10pcs 10-50W 15Wx2 Audio Power Amplifier DC 6 -18V TDA7297 Module Double ChannelRead More
LILYGO TTGO ESP32-Micro32 ESP-32-PICO WIFI Wireless bluetooth Control Module
$20.57Smart ModuleAdd to cartFeatureSeries:ESP32Model:ESP32-+MicroType:Regulator ICPower:1WApplication areas:household appliances, smart home, wearable devices, Internet of Things IoTDescriptionsESP32 vcc range:2.2V-3 6VVBAT:direct to battery (and charger)VUSB:direct to USB(5V)VCC:Output of regulator 3.3V/600mAUp to 250mA during RF transmissionsWirelessWifi:802.11 b/g/n/e/iWPA/WPA2/WPA2-Enterprise/SPSbluetooth:bluetooth 42BLESize:1.9×1.3cm/0.75×0.51inchNotePlease allow 1-3mm error due to manual measurement. pls make sure you do not mind before you bid.Due to the difference between different monitors, the …
LILYGO TTGO ESP32-Micro32 ESP-32-PICO WIFI Wireless bluetooth Control ModuleRead More
50Pcs 915MHz SW915-TH12 Copper Spring Antenna for Wireless Communication Module
$28.90Module ComponentsAdd to cartFeaturesSW915-TH12 copper spring antenna is a special antenna for 915MHz wireless communication system design. The antenna has good standing wave ratio, compact shape, ingenious structure, convenient installation, stable performance and good anti-vibration and aging ability.SpecificationFrequency range:915 MHz (+/-5)Standing wave ratioInput impedance:50Maximum power:5WGain:2.15 dBiWeight:1gHeight:12.5+/-1 mm (9T)Antenna color:copperInterface Form:Direct WeldingPackage included50 x Antenna
5Pcs 360 Degree Rotary Encoder Module Encoding Module
$11.83Other Module BoardAdd to cartFunctional characteristics and technical parameters 1)Nominal voltage:DC 5V 2)Wire A, B:0.5mA (Max 5mA; Min 0.5mA) 3)Common wire:1mA (Max 10mA; Min 0.5mA) 4)Temperature range:-30→ to+80→ 5)Output signal A , B phase position output square wave, when clockwise rotation, A phase position pull ahead B phase position 90 °, when anti-clockwise, B phase position pull ahead A …
5Pcs 360 Degree Rotary Encoder Module Encoding ModuleRead More
RD21F Delay Relay Module Power for Delay off Fan Module AC 100V-220V Time 0.2S-300min Adjustable Delay
$13.11Relay ModuleAdd to cartSpecificationsVoltage:100V-220V ACPower consumptionOutput:The output voltage is the same as the input voltage, and the maximum power supply capacity is 10A.Size:88* 36 * 22mmScrew hole:center distance 83mm * 31mm, aperture 3.2mmTime range:(4 files, selected by switch)First gear:range 0.2 seconds-30 seconds, accuracy:0.1 secondsSecond gear:range 0.2 seconds – 300 seconds (5 minutes), accuracy:0.3 secondsThird gear:range 0.2 seconds-30 minutes, …
Reviews
There are no reviews yet.