5pcs 3V/3.7V To 5V 1A Lithium Battery Step Up Module Board Mini Mobile Power Boost Charger Module with Undervoltage indication
$28.62
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Features
1. Using high quality chips and expanding MOS tubes.
2. The output current is expanded to 1A, and the maximum output is 1.5A. The 2A Schottky diode is used to recharge the balance.
3. With the new scheme design, the circuit design does not require electrolytic capacitors and tantalum capacitors (the electrolytic capacitors have a short life and the tantalum capacitors are in danger of explosion). 3 ceramic capacitors (MCC) used in high-end circuits.
4. The same load indicator and undervoltage indication (when the battery voltage is less than 2.7V, the indicator will go out under load, when the battery voltage is greater than 2.7V with load, the indicator light is on, when there is no load, the indicator light is micro bright).
5. Ultra-small size, 14.1*18.8*5.5 mm.
6. The circuit conversion efficiency is high, the efficiency is higher than 90%, and the efficiency of the single-cell lithium battery is also less than 80%.
7. Input low power reverse connection protection. If your battery has 2A protection board, the protection board will protect when you input the positive and negative poles of the power supply. Note that when there is no protection board or the input current is greater than 2A, the input reverse connection protection Will fail, will cause the module to be damaged, remember.
8. Ultra-low quiescent current, new version, quiescent current will be less than 100 microamps. No connection is required to connect to the battery.
Specifications
Input voltage:1-5V
Output voltage:5.1-5.2V
Output current:rated 1A-1.5A (single-cell lithium battery input), maximum 1.5A (single-cell lithium battery input)
Conversion efficiency:up to 96% (the higher the input voltage, the higher the efficiency)
Switching frequency:500KHz
Output ripple:30mV (MAX) 20M bandwidth (input 4V output 5.1V 1A)
Undervoltage indication:LED with load LED is on (input voltage is lower than 2.7V LED is off)
Operating temperature:industrial grade (-40 ° C to +85 ° C)
Full load temperature rise:30 ° C
Quiescent current:130uA
Load adjustment rate:±1%
Voltage regulation rate:±0.5%
Dynamic response speed:5% 200uS
Short circuit protection:None, if you want to have short circuit protection, you can input the lithium battery protection board or use a protected lithium battery.
Input reverse connection protection:none
Wiring method:welding
Input mode:IN+ input positive, IN- input negative
Applications
1).DIY a mobile power supply, you only need to input a battery power input, you can output 5V voltage to charge your mobile phone, MP3, MP4, PSP, very simple and convenient.
2). Power your electronic equipment. When your equipment needs 5V power supply, but now you only have lithium battery power supply, use this module to directly boost to 5V, solve your troubles.
3). The system is powered by the front stage. When you input the battery (1-5V) when you are working on a project, and your system board needs 5V stable power, then you choose this module will be your most. Good choice, you can work without commissioning directly on the machine, easily achieve high efficiency and high power boost.
Frequently Asked Questions and Answers
1. Why is my module designed to this shape
A:Our module is designed for your convenience. You can also remove the USB holder and solder the module directly to the PCB. The package is DIP-24.
2. How efficient is the module working I use it on the battery and it is very efficient. Can I use it
A:The efficiency of this module is very high in non-synchronous rectification. The highest efficiency of our test can reach 96%. There is also friends who do not blindly pursue high efficiency, high efficiency is proportional to the price, for example, you need 5V 0.5A power supply, 80% efficiency loss energy is 0.625W, 90% efficiency loss energy is 0.278W, Do you think it is necessary to double the cost of this 0.3W power It is ok to choose a combination.
3. Is this power module short-circuit protected When I use it, I accidentally output a short circuit and it will burn out
A:There is no short circuit protection. If you need short circuit protection, please connect the self-recovery fuse in series at the input.
4. Does this power module have input reverse connection protection When I use it, I accidentally input the power supply and it will burn out when I reverse it.
A:There is no reverse protection
5. Can this module current run at 5V 500mA for a long time
A:This module has a design power of 2.5W. It can run for a long time at 2.5W, and 5V*0.5A=2.5W can be operated for a long time. .
6. I need a current of about 2A. Can this module work in parallel
A:Direct parallel connection is not possible. There will be a large circulation between them. If you want to output parallel operation, you need to adjust the voltage of each module to a uniform error of less than 50 mV, so that it can work. Care should be taken to avoid overloading a single module and the output power should not exceed 70% of the total power of the module.
7. What is the working temperature of this module, can it reach the industrial level
A:Yes, the working temperature is -40 to 85 degrees.
Weight | 0.015 kg |
---|
Customers Also Viewed
5pcs RS232 to TTL Serial Converter Module DB9 Connector MAX3232 Serial Module with Cable
$21.38Converter BoardAdd to cartFeatureIt is widely used in radio modification, phone flash, GPS, vehicle detection, DVD flash, hard disk repair set-top box upgradeIt can be used to program STC MCU, NXP MCU, Renesas MCU, STM32 MCU, N+-2EC MCU CommunicationPort:TX RX VCC GNDChip:domestic MAX3232Package includes5 x Serial Module5 x Cable
Original JYETech 13805K DSO138mini DIY Digital Oscilloscope Kit SMD Pre-soldered with Case
$37.91DIY Electronic KitsAdd to cartDSO138mini brings in the following improvementsBetter structure and smaller size. The bulky pin-headers connecting the LCD and main board in old DSO138 has been eliminated. The soldering of these pin-headers has being found problematic for beginners.USB or battery powered. This makes the scope much more convenient to be used as a portable device. New version …
Original JYETech 13805K DSO138mini DIY Digital Oscilloscope Kit SMD Pre-soldered with CaseRead More
CJMCU-2112 CP2112 Evaluation Sensor for CCS811 Debugging Board USB to I2C Communication Converter Module
$16.67Sensor & Detector ModuleAdd to cartFeatureDirect connection to PC via USBDirect connection to host system via I2CSimple software GUI for easy setup and data loggingDetermine the effects of Temperature & HumidityIntelligent algorithms to output TVOC / eCO2 levelsPackage includes1 x Sensor Module
3 Pcs Red Acrylic Wall Mounted Protective Case Support Cooling Fan for Raspberry Pi 4 Model B
$35.10Raspberry Pi & Orange PiAdd to cartDescription– Wall Mounting Available– Red Blue Black Optional– Support Adding Cooling Fan– Compatible With Raspberry Pi 4B– Make of Transparent Acrylic, could check the board status easilyThere is a Protective Film on the board surface, please take it off before using.Package Included3* RED Acrylic Case Kit
5pcs CTS DTR USB Adapter Pro Mini Download cable USB to RS232 TTL Serial Ports CH340 Replace FT232 CP2102 PL2303 UART TB196
$23.80Converter BoardAdd to cartFeatures– This product use CH340 chips, stable performance, fully compatible with USB1.1,USB2.0,USB3.0 , baud rate up to 256 kbps; – Uses:Replace FT232 for Arduiuo Pro Mini Download – With receiver indicator,transmitter indicator, and power indicator.– Chip:CH340C– Compatible with PRO MINI download port– Board size:18mm x 30mm(Does not include USB ports and pins)– Supports the following …
10Pcs XH Pitch 2.54mm Single Head 4Pin 4Way Wire To Board Connector 15cm 24AWG with Socket
$6.55Electronic Accessories & SuppliesAdd to cartFeatureType:XH2.54 Single Head WirePin Number:4 PinWire Gauge:24AWG Pitch:2.54mmLength:15cmQuantity:10 Sets(10Pcs Single Head Wire + 10Pcs Socket )Note:the cable color may have different.Package included10 x XH2.54 Single-Head 4Pin 4Way Wire To Board Connector10 x Socket
2.4G Wireless Remote Control Module Transmitter and Receiver Module Kit Transmission Reception Communication 6 Channel Output
$8.26Smart ModuleAdd to cartTY24D-TX is the transmitting module, TY24D-RX is the receiving module. The transmitting module only needs to provide 3.3V power supply and transmitting button and one LED as the transmitting status indication. The output port corresponding to the receiving module can output the level signal, and the module has the output status. Select to select the …
2M*45cm Window Film Privacy Static Cling Stained Glass Sticker Home office Decor
$30.50PlasticsAdd to cartSpecificationsMaterial:PVCSize:45cm X 200cmFeatures– Energy-saving and environmental protection. No gum paste, paste can be repeated.– Deadening UV intrusion, protecting indoor objects fading and aging.– Filter light and reduce glare, protect the skin and vision.– Easy to mount and clean.How to use1. First clean the surface of the pasting position, pasting surfaces should be smooth, not be …
2M*45cm Window Film Privacy Static Cling Stained Glass Sticker Home office DecorRead More
Reviews
There are no reviews yet.