10pcs Stereo Audio Isolator Common Anti-interference Signal Generator Noise Filter Computer Audio Current Sound Canceller
$53.12
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Features
1. Parts selection:two independent audio are used, and the former material is selected from aerospace materials.
High sensitivity and high reductivity, higher sensitivity than 10-120DB of similar low-end formers, full tone and pure sound quality.
2. Line design:stereo dual-channel independent design, circuit board specifications:45MM X 30MM, very small, suitable for small spaces and other automotive interior installation.
3. Connection method:Two connection methods, which can be input and output through the 3.5MM headphone jack, or directly through two blue wiring sockets.
4. Main function:Eliminate current sound. The common isolated audio former eliminates the current sound brought by the AUX common ground, and the output and output ground wires are isolated by the former, and there is no common ground.
What is the common ground
This product is an audio common ground isolator, which effectively suppresses the noise caused by the common ground for the sound source and the receiving device.
So what is the common ground To put it simply, the ground point of the two electrical appliances is not at the same point. Due to the difference in grounding resistance, noise is mitted into the electrical equipment through the ground wire to form interference. Because the grounding points of the two devices are different, it is possible to generate common ground noise. The noise is mainly reflected in the car audio, that is, there is an audio interference, like the whistling sound, the frequency of this noise will change with the engine speed. Therefore, this product can only eliminate the noise and current sound generated by the common electricity, and can not eliminate the noise caused by other reasons, so you need to confirm the source of the noise yourself.
Determine if noise is caused by common ground
1. Use the earphone to connect with the car MP3 and car navigation AUX (3.5mm interface). If the sound heard from the earphone is no noise at this time, it can be confirmed that the noise of the car device is caused by the common ground.
2. Use the audio cable to connect the battery-powered mobile phone, or MP3 (note that the mobile phone, MP3 is not connected to any power source on the car, such as a telephone), and the AUX of the car center console, and play the music of the mobile phone. Noise can confirm that the noise was caused by the common ground.
3. Computer, amplifier, stereo, CD:Use a passive headset to plug in the computer to hear if there is noise, use the phone to plug in the amplifier, audio audition, if there is no noise, the basic judgment is caused by the common ground.
4. After starting the car, the installed amplifier has a current sound. In some models, the throttle is larger and the current is louder. This product can solve this problem.
5. There is a current sound between the amplifier and the speaker or the sound. This product can be installed between the amplifier and the speaker.
6. When the laptop is connected to the projector and the amplifier is connected with noise, you can connect the adapter to the power supply or use the battery. At this time, unplug the amplifier and disappear, or unplug the projector and the noise will disappear. Then you can use the headphone jack and amplifier of the computer. Add a common ground isolator to eliminate noise.
Package Included
10 x Stereo Audio Isolator Common Anti-interference Signal Noise Filter
Weight | 0.02 kg |
---|
Customers Also Viewed
Multiple Car Toys Magnetic Puzzle Box Book Educational Book Kids Learning Gift
$52.64MathematicsAdd to cartPackage included10 x Card76 x MagnetsFeatures1.Developing kids’ intelligence.2.Teaching kids to know more words.3.Easy for storage.SpecificationsColor:MulticolorMaterial:Paperboard, MagnetismSize:30x4x21.5cm
Basic Starter Kit UNO R3 Mini Breadboard LED Jumper Wire Button with Box for Geekcreit for Arduino – products that work with official Arduino boards
$18.62Module KitsAdd to cartDescriptionsPerfect for Shield Prototyping and TestingPlastic housing, metal contact clipsAccept wire with diameter 20-29AWGVolatge/current:300V/3-5A400 tie-point2 Power Lanes, Tie-point 1001 Double-strip, Tie-point 300Solderless Breadboard Size:82x55x8.5mmPackage included1 x Uno R3 Development Board1x 400 hole Breadboard10 x 220Ω resistor 5% carbon film10 x 1k resistor 5% carbon film10 x 10k resistor 5% carbon film10 x 100k resistor 5% …
3pcs ESP32-S WiFi + Bluetooth ESP32S Serial to WiFi Dual Antenna Module
$29.27Smart ModuleAdd to cartDescriptionThe main chip uses a low-power dual-core 32-bit CPU with a frequency of up to 240MHz and computing power of up to 600DMIPS.Default 32Mbit SPI Flash, 520KB SRAMSupport SoftAP and Station modeUltra-small 802.11b/g/n Wi-Fi + BT/BLE SoC moduleSupport UART/SPI/I2C/I2S/PWM/ADC/DAC, etc.Support for firmware upgrade (FOTA)Antenna supports onboard antenna or IPEX block outputPackage includes3 x Wifi module
Geekcreit 433MHz DC 12V 10A Relay 1CH Channel Wireless RF Remote Control Switch Transmitter with Receiver
$15.30Smart ModuleAdd to cartIf you need more Transmitter, please buy Product ID:1215079>>>Manual:Click here to openFeaturesEasy to install and easy to carryWith a slidable cover on the remote controlWith a hook on the remote controlUse Learning coding, stable and reliableThe wireless signal can pass through walls, floors and doorsYou can turn on or turn off the receiver with transmitter …
CO2 Refill Adapter Connector Kit W21.8-14 Thread Set for Filling SodaStream
$56.69Electrical Pump & ValveAdd to cartFeature*CO2 Refill Adapter is used to fill CO2 into your Sodastream tank.*Adjustable valve pin ensures compatibility with any cylinder valve variation.*Easy to install and use.*Made of high quality metal, high hardness and durable.Specification*Material:Metal*Color:Silver (As Pictures Show)*Inner Thread:TR21-4*Outer Thread:W21.8-14Package Contents1*CO2 Refill AdapterNotes:The real color of the item may be slightly different from the pictures shown on …
CO2 Refill Adapter Connector Kit W21.8-14 Thread Set for Filling SodaStreamRead More
30pcs 2.5-5.5V TTP223 Capacitive Touch Switch Button Self Lock Module
$15.15Other Module BoardAdd to cartFeatures 1. Size:15*11mm 2. Power:2.5-5.5V 3.Trigger setting mode:(1->Short;0->No Short) AB=00:No-lock High TTL level output; AB=01:Self-lock High TTL level output; AB=10:No-lock Low TTL level output; AB=11:Self-lock Low TTL level output; Package included 30 x 2.5-5.5V TTP223 Capacitive Touch Switch Button Self-Lock Module For
NE555 Pulse Module LM358 Duty and Frequency Adjustable Square Wave Signal Generator Upgrade Version
$6.55Test & Measuring ModuleAdd to cartFeature1. Used as a square wave signal generator to generate square wave signals for experimental development.2. Used to generate a square wave signal that drives the stepper motor driver.3. Generate adjustable pulses for use by the MCU.4. Generate adjustable pulses to control the associated circuitry.Description1. Size:3.5CM * 4.6CM1. The main chip:LM358;2. Input voltage:5V-12VDC.3. Input current:≥100MA;4. …
3pcs LM3915 Level indicator Kit DC9V-12V DIY Electronic Production Module Kit
$13.73DIY Electronic KitsAdd to cartFeatureModel:AUL-10Supply voltage:DC9V-12VAudio input:0~1.5VrmsPCB size:66 x 28mm (L x W)Light row size:62.5 x 5 x 10.7mm (L x W x H)Two indication modes:bar indication and fire spot indication (Realized by MOD short-circuit point)Lamp row offers two kinds of vertical and horizontal installationTin-treated solder padsNote:Before power on, please confirm the polarity of the power supply is correct …
3pcs LM3915 Level indicator Kit DC9V-12V DIY Electronic Production Module KitRead More
Reviews
There are no reviews yet.