3pcs HC-SR501 Adjustable infrared IR Pyroelectric PIR Module Motion Sensor Human Body induction Detector
$8.65
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Features
1. Automatic induction:When someone enters its induction limits, enter the high level, people leave the sensor range is automatically delayed off high. Output low.
2. photosensitive control (optional):the module reserved for location, can be set to photosensitive control, strong light during the day or not induction. Photosensitive control is optional, the factory did not install the photosensitive resistor. If necessary, please buy a separate photosensitive resistor to install.
3. Two trigger modes:L is not repeatable, H is repeatable. Can be jumper selected, the default is H.
A. non-repeatable trigger mode:the induction output high, the delay time is over, the output will automatically change from high to low.
B. Repeated trigger mode:that is, after sensing the output high, in the delay time period, if the human body in its sensing limits of activities, its output will remain high until the delay after the person will leave the high The level changes to low level (the sensing module automatically delays a delay time after every activity of the human body, and takes the time of the last activity as the starting point of the delay time).
4. Induction blocking time (default setting:3-4 seconds):After each sensing output (high level goes low), the sensing module can be followed by a blocking time, during which it is sensed The device does not receive any sense signals. This function can be used to achieve the interval between the sensing output time and the blocking time. It can be applied to the interval detection products. At the same time, this function can effectively suppress all kinds of interference in the process of load switching.
5. Wide operating voltage:the default operating voltage DC5V to 20V.
6. Micro-power:Quiescent current 65 microamps, especially for dry battery-powered electrical products.
7. Output high-level signal:can be easily with various types of circuits to achieve docking.
Instructions for use
1. Induction module power about one minute after the initialization time, at this time the module will output 0-3 times a minute, a minute into the standby state.
2. Light and other interference should be avoided Directly close the surface of the lens module, so as not to introduce interference with the signal to produce malfunction; use of the environment as far as possible to avoid
Free flow of wind, the wind will cause interference to the sensor.
3. Sensor module with dual-element probe, the probe window is rectangular, dual element (A yuan B yuan) in the longer direction at both ends, when the body from left to right
Or from right to left through the infrared spectrum to the dual time, distance difference, the greater the difference, the more sensitive induction, when the body from the front to the probe
Head or from top to bottom or from bottom to top direction, the dual element can not detect infrared spectral distance changes, no difference, so the sensor insensitive or does not work; so the sensor should be installed so that the direction of the probe dual And the direction of human activity as much as possible parallel to ensure that the body has been through
Probe dual-element induction. In order to increase the sensing angle limits, this module uses a circular lens, also makes the probe four sides are sensitive, but the left and right sides are still
However, compared with the upper and lower direction of the two induction limits, sensitivity, installation must still try to according to the above requirements.
Use should pay attention to the following points
1. The DC voltage must meet our requirements, too high and too low will affect the performance of the module, but also requires the power supply must be a good regulator filter, such as computer USB power, mobile phone charger power supply, the old 9V stacked battery Are unable to meet the module work requirements, it is recommended that customers use the power transformer and the regulator through the three-terminal voltage regulator and then through the 220UF and 0.1UF capacitor filter power supply.
2. Although the human body is not in front of the module, but the human body from the module is too close to the module can also be caused by the sensor output, as well as debugging the human body do not touch the circuit part will also affect the module work , A more scientific approach is to output a LED or a multimeter, the module covered with a newspaper, when someone leaves room, wait 2 minutes and see if the module still has output.
3. The module does not take the load to work properly, connected to the load after the work of chaos, one reason is because the power capacity is very small load power consumption, load caused by voltage fluctuations caused by the module malfunction, the other reason is the load The power will have interference in the work, such as relays or electromagnets and another inductive load will produce a reverse electromotive force, 315M emission plate will have electromagnetic radiation and other work will affect the module. The solution is as follows:A, the power part of the inductor filter. B, using the load and the module using different voltage methods, such as:load using 24V operating voltage, the module uses 12V operating voltage, during which the use of three-terminal regulator isolation. C:Use a larger capacity power supply.
4. The human body sensor module can only work indoors and the work environment should avoid the sun, a strong direct light exposure, if the work environment has a strong RF interference, you can use shielding measures. In case of strong air interference, close the doors and windows or prevent convection. The induction area to avoid facing heating appliances and objects as well as easy to wind debris and clothing.
5. The human body sensor module is recommended to install in a sealed box, otherwise, there may have been the output signal.
6. If the body sensor module detection angle is less than 90 degrees, you can use opaque adhesive tape to cut off the lens or cut lens to achieve.
7. The human body sensor module with dual-element probe, the body’s hands and feet and head movement direction and the sensitivity of the sensor are closely linked, and the infrared module determines the characteristics of the sensor can not accurately control the distance.
8. The module of the probe (PIR) can be mounted on the other side of the circuit board. The probe can also be extended with a two-core shielded cable, the length should be less than 20 cm as well.
Package includes
3 x HC-SR501 Motion Sensor
Weight | 0.027 kg |
---|
Customers Also Viewed
REX-C100 Digital RKC PID thermostat Temperature Controller 0 To 400 Degree K Type Relay Output
$24.04Electronic Accessories & SuppliesAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.FeaturesThis is a double universal programmable digital display temperature controller that supports many types of thermocouple sensor.It is powered by 220V ACSpecificationsScreen:Double screen for Celsius (C)Range:0-400C (Only when with K-type thermocouple factory)Thermocouple:K, …
High Gain 10dB 2.4G Wifi Directional Image Transmission Yagi Antenna
$20.07RF amplifierAdd to cartSpecificationWorking frequency:2.35-2.55GHZAntenna gain:10.5dB (typical value)Antenna standing wave ratioPower capacity:10WMechanical size:5x10Cm (excluding joints)Radiation direction:directional linear polarizationConnector type:SMA-K (standard female, outer screw and inner hole, can be customized)Package included1 x Antenna
20pcs DD2712SA 3.5A Mini 5V-27V to 12V DC DC Step Down Buck Power Converter Module Voltage Regulator
$83.70Boost & Buck ModuleAdd to cartDescriptionInput voltage:5-27VOutput voltage:5V Maximum output current:2.5AShort time maximum output current:3.5A Quiescent current:about 250uAWorking frequency:900KHz.Working efficiency:77-92% Size:25 x 15 x 6.3 mmOvertemperature shutdown, Under-Voltage Lockout (UVLO), BS-voltage protection, and short circuit protection.Note1. Input voltage can not be greater than the maximum input range.2. Output power can not be greater than the maximum load for a long …
Quick Charge 3.0 DIY Power Bank 18650 Battery Case QC3.0 5V 9V 12V DIY Kit Power Bank 2A 18650 Battery Fast Charger Shell
$25.14Module ComponentsAdd to cartNote1. Please Use flat-headed 18650 DIY2. If use the old battery,pls test the voltage,more than 3.5v and the Internal resistance less than 60 .3. It can’t use the flashlight 18650 battery4. Do not connect the positive and negative terminals backwards, otherwise it will burn the circuit board5. Don’t close the cover until the test is …
25x25x5cm Soundproofing Triangle Sound-Absorbing Noise Foam Tiles
$14.16FoamAdd to cartDescription25x25x5cm Soundproofing Triangle Sound-Absorbing Noise Foam TilesSpecificationsMaterial:Polyurethane foamDimensions:25 * 25 * 5 cm / 9.84 * 9.84 * 1.97 inchBlack:ColourQuantity:1pcFeatures– Bounce rate deformation, a long duration.– Waterproof, anti-moisture, good air permeability.– Wherever to help block sound and prevent echoes in the room.– These panels provide a strong noise reduction, good for studios, recording studios, vocal …
25x25x5cm Soundproofing Triangle Sound-Absorbing Noise Foam TilesRead More
Reviews
There are no reviews yet.