Constant Voltage Constant Current Step Down Module with LED Display Battery Charging Board DC 5-36V
$19.67
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Features
1, On-board voltage, current and power meter. This module can be easily used without a multimeter, which is simpler and more intuitive.
2, On-board USB interface, can easily charge digital products. (Note:The USB output voltage is the same as the module output voltage. It is not a fixed 5V output. Please confirm before charging the USB device.)
3, High power, high efficiency, 5A, low ripple;
4, Three major functions
(1) Used as a normal step-down module with overcurrent protection capability;
(2) It is used as a charger for various voltage value lithium batteries, batteries, nickel-cadmium nickel-hydrogen batteries (battery packs), and used in solar panels, wind turbines, etc.;
(3) Used as a high power LED constant current driving module;
5, With constant voltage and constant current two modes, there are indicators to indicate which mode the module is currently in;
6. When used as a lithium battery charger, you can set the float voltage and the charge current. There are indicators to indicate whether it is charging is already full;
7, With current limit protection, even if the output is short circuit will not burn the module.
8, On-board voltage, ammeter can be self-calibrated, there will never be inaccurate problems!
Specifics
Input Voltage:DC 5V To 36V (digital tube correctly displays power supply above 6.7V)
Output Voltage:1.25-32V continuously adjustable (input voltage needs to be 1.5V higher than the output voltage)
Output Current:adjustable, up to 5A (recommended for use within 4.5A)
Output Power:up to 75W (recommended to use within 50W, please reduce power when using large differential pressure)
Working Temperature:-40~+85 degrees
Working Frequency:180KHz
Conversion Efficiency:up to 96%
Is Short Circuit Protection:Yes
Is Over Temperature Protection:Yes (automatically turn off the output after over temperature)
Input Reverse Connection Protection:None, (If necessary, please input a large current diode in the input string)
Installation Method:4 3mm silk
Wiring Method:Terminal block or soldering terminal, V-IN is input, V-OUT is output.
Application range
1. Use as a normal buck module with overcurrent protection
(1) Press the right button to adjust the digital meter to the [Display Output Voltage] interface, and adjust the “Constant Piezo Transistor” to make the output voltage reach the desired voltage value;
(2) Adjust the digital meter to the [display output current] interface, directly short the output end of the module (find a thick wire to short the output end), adjust the ‘constant current potentiometer’ to make the digital meter The current value reaches the preset overcurrent protection value; (for example, if the current value displayed by the onboard ammeter is 4A, then the maximum current of the module is limited to 4A, and the red indicator light is bright when the current reaches 4A)
(3) Connect the load and work.
2. Use as a battery charger
Modules without constant current function cannot be used to charge the battery. Because of the large voltage difference between the battery and the charger.
Causes the charging current to be too large, causing damage to the battery, so start charging the battery with constant current when charging
Automatically switch back to constant voltage charging to a certain extent.
(1) Determine the float voltage and charge current of the battery; (if the lithium battery parameter is 3.7V/2200mAh, then the float voltage is 4.2V, and the maximum charge current is 1C, ie 2200mA)
(2) Under no-load conditions, adjust the digital meter of the module to the [display output voltage] interface, and adjust the ‘constant piezoelectric positioner’ to make the output voltage reach the float voltage;
(3) Adjust the digital meter to the [display output current] interface, and directly short the output end of the module (find a thick wire to short the output end), then adjust the ‘constant current potentiometer’ to make the digital meter The current value reaches a preset charging current value;
(4) The charging lamp current defaults to 0.1 times the charging current; (the battery is gradually reduced during the charging process, gradually changing from constant current charging to constant voltage charging, if the charging current is set to 1A, then when When the charging current is less than 0.1A, the blue light is off, the green light is on, and the battery is charged.
(5) Connect the battery and charge it. (Steps 1, 2, 3, and 4 are:input terminal is connected to the power supply, and the output terminal is not connected to the battery.)
3. Use as LED constant current drive module
(1) Determine the operating current and maximum operating voltage at which you need to drive the LEDs;
(2) Under no-load conditions, adjust the digital meter to the [display output voltage] interface, adjust the ‘constant piezoelectric positioner’ to make the output voltage reach the LED working voltage;
(3) Adjust the digital meter to the [display output current] interface, and directly short the output end of the module (find a thick wire to short the output end), then adjust the ‘constant current potentiometer’ to make the digital meter The current value reaches a preset LED operating current;
(4) Connect the LED and test the machine.
(Steps 1, 2, and 3 are:input is connected to the power supply, and the output is not connected to the LED light)
Precautions
1. Do not share the input ground and output ground of the module. This will cause the module current sampling resistor to bypass, so that the module can not adjust the output current. It is easy to burn the module when the load is connected.
2. The output of the module has a current sampling resistor. After the load is connected, there will be a voltage drop of 0~0.2V, which is normal.
3. When the module output voltage cannot be adjusted, please turn the potentiometer counterclockwise for more than 10 turns, then use the module to adjust the voltage normally.
4. When the output exceeds 3A or 35W, please strengthen the heat dissipation!
Package Included
1 x Step Down Module
Weight | 0.075 kg |
---|
Customers Also Viewed
K202 Low Power Consumption Fingerprint Control Board Switch Fingerprint Access Control Board DC12V
$17.48Other Module BoardAdd to cart>>>Manual:Click here to openSpecifications·P1:Power supply:DC12V·Output:Relay(Max. current:10A)·Standby current:15uA·Fingerprint capacity:120 pieces·Size:64.4*25.4mm·P2:MX 1.0mm space 6 Pin Fingerprint Module(can connect R502,R502-A,R502-AW,R503)·P3:MX 1.25mm space 6 Pin Fingerprint Module(can connect R300,R301T,R303,R303T,R305,R306,R307,R501)K202 is designed for low power consumption, the power supply is DC12V, the relay time can be adjusted by rotating the button, relay time:0.5-13 seconds.It is very easy to register fingerprint, …
intelligent Voice Recognition Module AC108 Audio Decoding Module 4 Microphones Decoder for Smart Speaker DIY
$28.42Expansion Board & ShieldAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.Feature1. Based on RASPBERRY PI 40PIN interface, suitable for RASPBERRY PI series motherboards;2. Support RASPBERRY PI ZERO / ZERO W / 2B / 3B / 3B + / 4 and other development …
GP2Y1010AU0F Dust Sensor Module Dust Particle Concentration PM2.5 Haze Detection
$32.79Sensor & Detector ModuleAdd to cartFeaturesEasy to use:only one AD acquisition pin and one control pin are neededAnalog output:The output voltage is linearly related to the dust concentration in the effective range, with a built-in attenuation circuit, the output voltage does not exceed 1.5VSensitivity:0.5V/(100┢g/m3)Effective range:500┢g/m3Wide power supply range:built-in booster circuit, working voltage range 2.5V to 5.5VLow power consumption:within a sampling …
GP2Y1010AU0F Dust Sensor Module Dust Particle Concentration PM2.5 Haze DetectionRead More
3pcs TM1637 4 Bits Digital LED Display Module 7 Segment 0.36 inch RED Anode Tube 4 Serial Driver Board for
$11.00Display ScreenAdd to cartIntroductionThe module is a 12-pin display module with a 4-point common digital tube (0.36 inch) with a clock point. The driver chip is TM1637. It only needs 2 signal lines to enable the MCU to control the 4-bit 8- Segment digital tube.FeaturesDigital Tube:4-digit common anode with a 0.36-inch digital tube with a score point, highlighted …
1080P HDMI Male to 3RCA Audio Video AV Output Transmit Cable Adapter 1.5M/5Feet
$7.86Expansion Board & ShieldAdd to cartFeatures– Gold plated connectors for better signal transfer.– New generic HDMI Male to 3 RCA Audio Video AV Component.– HDMI to RCA cable is designed to connect and transfer signals from HDMI port to RCA port.– High quality HDMI- RCA cable suitable for use in HDTV, Home Theater systems, and all other HDMI to RCA …
1080P HDMI Male to 3RCA Audio Video AV Output Transmit Cable Adapter 1.5M/5FeetRead More
LED Strip Switching Power Supply AC110V-240V to DC12V 60W 5A 160*40*32mm S-60-12
$35.59Power Supply ModuleAdd to cartFeature1. International AC input range2. High efficiency, low working temperature3. Short circuit,overload,over-current protection4. 100% fully load burn-in test5. Built-in EMI filter, low ripple noise6. Low cost, high reliability7. CE and FCC approvalSpecification1. LED switching power supply using pulse width modulation (PWM) switching technology designed to ensure power supply stability and high efficiency. 2. Product interference, …
LED Strip Switching Power Supply AC110V-240V to DC12V 60W 5A 160*40*32mm S-60-12Read More
5pcs TB371 4 Key MCU Keyboard Button Board Compatible UNO MEGA2560 Pro Mini Nano Due for Raspberry Pi Teensy++ Geekcreit for Arduino – products that work with official for Arduino boards
$14.12Other Module BoardAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.Description1. 4-button Common Cathode key module(When pressed output low level). 2. GND K1 K2 K3 K4′ 4 PIN OUT 2.54mm3. Working voltage:DC 0-48V 4. Size:12.7 x 33mm5. It can be inserted directly …
TCRT5000 infrared Reflective Switch IR Barrier Line Track Sensor Module
$4.36Sensor & Detector ModuleAdd to cartTCRT5000 Infrared Reflective Switch IR Barrier Line Track Sensor ModuleFeaturesTCRT5000 sensor of infrared emission diode constantly launch infrared, the infrared ray is emitted when the intensity of reflected back has not been reflected or but is not big enough, the light activated triode has been in the off state, the output end of the module …
TCRT5000 infrared Reflective Switch IR Barrier Line Track Sensor ModuleRead More
Reviews
There are no reviews yet.