Constant Voltage Constant Current Step Down Module with LED Display Battery Charging Board DC 5-36V
$19.67
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Features
1, On-board voltage, current and power meter. This module can be easily used without a multimeter, which is simpler and more intuitive.
2, On-board USB interface, can easily charge digital products. (Note:The USB output voltage is the same as the module output voltage. It is not a fixed 5V output. Please confirm before charging the USB device.)
3, High power, high efficiency, 5A, low ripple;
4, Three major functions
(1) Used as a normal step-down module with overcurrent protection capability;
(2) It is used as a charger for various voltage value lithium batteries, batteries, nickel-cadmium nickel-hydrogen batteries (battery packs), and used in solar panels, wind turbines, etc.;
(3) Used as a high power LED constant current driving module;
5, With constant voltage and constant current two modes, there are indicators to indicate which mode the module is currently in;
6. When used as a lithium battery charger, you can set the float voltage and the charge current. There are indicators to indicate whether it is charging is already full;
7, With current limit protection, even if the output is short circuit will not burn the module.
8, On-board voltage, ammeter can be self-calibrated, there will never be inaccurate problems!
Specifics
Input Voltage:DC 5V To 36V (digital tube correctly displays power supply above 6.7V)
Output Voltage:1.25-32V continuously adjustable (input voltage needs to be 1.5V higher than the output voltage)
Output Current:adjustable, up to 5A (recommended for use within 4.5A)
Output Power:up to 75W (recommended to use within 50W, please reduce power when using large differential pressure)
Working Temperature:-40~+85 degrees
Working Frequency:180KHz
Conversion Efficiency:up to 96%
Is Short Circuit Protection:Yes
Is Over Temperature Protection:Yes (automatically turn off the output after over temperature)
Input Reverse Connection Protection:None, (If necessary, please input a large current diode in the input string)
Installation Method:4 3mm silk
Wiring Method:Terminal block or soldering terminal, V-IN is input, V-OUT is output.
Application range
1. Use as a normal buck module with overcurrent protection
(1) Press the right button to adjust the digital meter to the [Display Output Voltage] interface, and adjust the “Constant Piezo Transistor” to make the output voltage reach the desired voltage value;
(2) Adjust the digital meter to the [display output current] interface, directly short the output end of the module (find a thick wire to short the output end), adjust the ‘constant current potentiometer’ to make the digital meter The current value reaches the preset overcurrent protection value; (for example, if the current value displayed by the onboard ammeter is 4A, then the maximum current of the module is limited to 4A, and the red indicator light is bright when the current reaches 4A)
(3) Connect the load and work.
2. Use as a battery charger
Modules without constant current function cannot be used to charge the battery. Because of the large voltage difference between the battery and the charger.
Causes the charging current to be too large, causing damage to the battery, so start charging the battery with constant current when charging
Automatically switch back to constant voltage charging to a certain extent.
(1) Determine the float voltage and charge current of the battery; (if the lithium battery parameter is 3.7V/2200mAh, then the float voltage is 4.2V, and the maximum charge current is 1C, ie 2200mA)
(2) Under no-load conditions, adjust the digital meter of the module to the [display output voltage] interface, and adjust the ‘constant piezoelectric positioner’ to make the output voltage reach the float voltage;
(3) Adjust the digital meter to the [display output current] interface, and directly short the output end of the module (find a thick wire to short the output end), then adjust the ‘constant current potentiometer’ to make the digital meter The current value reaches a preset charging current value;
(4) The charging lamp current defaults to 0.1 times the charging current; (the battery is gradually reduced during the charging process, gradually changing from constant current charging to constant voltage charging, if the charging current is set to 1A, then when When the charging current is less than 0.1A, the blue light is off, the green light is on, and the battery is charged.
(5) Connect the battery and charge it. (Steps 1, 2, 3, and 4 are:input terminal is connected to the power supply, and the output terminal is not connected to the battery.)
3. Use as LED constant current drive module
(1) Determine the operating current and maximum operating voltage at which you need to drive the LEDs;
(2) Under no-load conditions, adjust the digital meter to the [display output voltage] interface, adjust the ‘constant piezoelectric positioner’ to make the output voltage reach the LED working voltage;
(3) Adjust the digital meter to the [display output current] interface, and directly short the output end of the module (find a thick wire to short the output end), then adjust the ‘constant current potentiometer’ to make the digital meter The current value reaches a preset LED operating current;
(4) Connect the LED and test the machine.
(Steps 1, 2, and 3 are:input is connected to the power supply, and the output is not connected to the LED light)
Precautions
1. Do not share the input ground and output ground of the module. This will cause the module current sampling resistor to bypass, so that the module can not adjust the output current. It is easy to burn the module when the load is connected.
2. The output of the module has a current sampling resistor. After the load is connected, there will be a voltage drop of 0~0.2V, which is normal.
3. When the module output voltage cannot be adjusted, please turn the potentiometer counterclockwise for more than 10 turns, then use the module to adjust the voltage normally.
4. When the output exceeds 3A or 35W, please strengthen the heat dissipation!
Package Included
1 x Step Down Module
Weight | 0.075 kg |
---|
Customers Also Viewed
15x15cm Woven Wire Cloth Screen Stainless Steel 304 60 Mesh
$13.35Mesh & Wire ClothAdd to cartDescriptionStainless Steel 304 Woven Wire Cloth Screen is widely used in acid and alkali environment screening andfiltration, barbecue nets, handicraft nets, food machinery nets, cooking nets.SpecificationMaterial:Stainless steelSize:15x15cm(6inchx6inch)Mesh:60ApplicationWidely used in acid and alkali environment screening and filtration, barbecue nets, handicraft nets, foodmachinery nets, cooking nets, can also be used for solid material classification filtering, liquid and …
15x15cm Woven Wire Cloth Screen Stainless Steel 304 60 MeshRead More
YJ-QCC3003 Bluetooth 5.0 Module for Power Amplifier Board
$47.10Amplifier BoardAdd to cartDetails1. The Bluetooth core uses QCC3003 chip, supports A2DP, AVRCP, HFP, AAC, I2S, etc., and uses 16M SPI FLASH memory chip. DAC adopts imported PCM51022. The electrolytic capacitor adopts the gold word SANYO 470UF/16V electrolytic capacitor to ensure strong and continuous power support.3. High-precision chip resistors are selected for the resistors to ensure a good …
YJ-QCC3003 Bluetooth 5.0 Module for Power Amplifier BoardRead More
10Pcs Orinigal M27C322-100F1 DIP-42 Mbit 32M EPROMs EPROM IC
$23.68Electronic Accessories & SuppliesAdd to cart10Pcs Orinigal M27C322-100F1 DIP-42 Mbit 32M EPROMs EPROMFeatureSuitable for microprocessor systems requiring large data or program storage.It is organised as 2 M Words of 16 bit. The pin-out is compatible with a 32 Mbit Mask ROM.The FDIP42W has a transparent lid which allows the user to expose the chip to ultraviolet light to erase the …
10Pcs Orinigal M27C322-100F1 DIP-42 Mbit 32M EPROMs EPROM ICRead More
120pcs 2.8 4.8 6.3 insert Plug Spring Sheathed Wire Terminal Connector Cold Pressed Terminal 0.5-2.5mm2 Connector
$7.32Electronic Accessories & SuppliesAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.DescriptionName:2.8mm Spring ConnectorsMode:DJ622-2.8Applied Wire Diameter:0.5-0.8mm2Material:Brass tinned(Sheath:flame retardant material)Usage:All the device switch,rocker switches,vehicles,battery and domesticuse.Name:4.8mm Spring ConnectorsMode:DJ622-4.8Applied Wire Diameter:0.5-0.8mm2Material:Brass tinned(Sheath:flame retardant material)Usage:All the device switch,rocker switches,vehicles,battery and domesticuse.Name:6.3mm Spring ConnectorsMode:DJ622-6.3Applied Wire Diameter:1.0-1.5mm2Material:Brass tinned(Sheath:flame …
5pcs 1 Channel DC 12V Relay Module Solid State Low Level Trigger 240V2A
$18.21Relay ModuleAdd to cartSpecificationInput Power Supply:12V DC Load Voltage:AC240V 2AMaximum operating current:13.8mATrigger mode:low levelInput control signal voltage(0-2.5V low state relay OFF)(3.3-5V state high relay ON)Blue KF301 terminal connection control line is more convenient.Module interfaceDC +:positive power supply (by relay voltage power supply)DC-:connect power negativeCH:Relay Module signal triggering end (Low level trigger effective)Note:Power must be DC voltage and need …
5pcs 1 Channel DC 12V Relay Module Solid State Low Level Trigger 240V2ARead More
Geekcreit ESP32 WiFi+bluetooth Development Board Ultra-Low Power Consumption Dual Cores Pins Unsoldered
$15.30Smart ModuleAdd to cartDescriptionESP32 is already integrated antenna and RF balun, power amplifier, low-noise amplifiers, filters, and power management module.The entire solution takes up the least amount of printed circuit board area.This board is used with 2.4 GHz dual-mode Wi-Fi and bluetooth chips by TSMC 40nm low power technology,power and RF properties best, which is safe, reliable, and …
RF Envelope Detector Amplitude Detection Discharge Signal Detection Module
$19.67RF amplifierAdd to cartDescriptionThis product uses a voltage doubler detector (consisting of two reverse microwave diodes), 1 time sensitive than single-tube detector(about 6dB),high sensitivity (typical -30dBm, or even to -40dBm) not ordinary 2AP9,1N60 can emulate.The envelope detection principleFeature1. Maximum input:20dBm2. Detection output:The default is positive3. Working Frequency:0.1-3200MHz4. RC Filter:R = 10K, C = 1nF; (two elements in parallel …
RF Envelope Detector Amplitude Detection Discharge Signal Detection ModuleRead More
ZPHS01 All-in-one Gas Detection Module Carbon Dioxide Dust PM2.5 Sensor PM2.5 + CO2 + VOC + Temperature + Humidity Detector
$129.99Sensor & Detector ModuleAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.NoteThis is PM2.5 + CO2 + VOC + Temperature + Humidity PM2.5 + CO2 + CH2O + Temperature + Humidity ID:1680902OverviewThis is an all-in-one module integrating VOC sensor, laser dust sensor, infrared …
Reviews
There are no reviews yet.