3Pcs PWM Stepper Motor Driver Simple Controller Speed Controller forward and Reverse Control Pulse Generation
$63.41
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Feature
Product name:simple controller
Model:CW-S01
It can generate PWM signal. There is a jumper on the board, which can be set and selected. By default, it is set to generate pulse frequency signal.
Product Manual
1. When the controller generates a pulse frequency signal, it can supply a stepper driver as a signal. To control the stepper motor, it must be equipped with a driver.
(This simple controller + stepper driver + stepper motor + DC power supply can form a simple control platform.)
2. The controller can generate a pulse frequency signal or a PWM pulse width signal. There is a jumper on the board, which can be set and selected. By default, they are set to generate pulse frequency signals.
REQ is to generate pulse frequency signal
PWM is to generate PWM signal
3. When the controller generates a pulse frequency signal, there are three types of high, medium and low frequency signals that can be selected with a jumper. The frequency parameters are approximately
High:5.8KHZ-127KHZ
Middle:590HZ-15.8KHZ
Low:82HZ-2.3KHZ,
Frequency measurement:You can measure PUL and common cathode (GND) two ports.
4. The power supply has 2 sets of power input, and 2 sets only need to connect one set of power supply. It is recommended to use a power supply of more than 15V. Connect to the power supply of the 2-bit terminal, do not connect the positive and negative.
One group is the power supply connected to DC 15-160VDC, and the recommended operating voltage is 15-80VDC.
The other group is 5-12VDC. When used with the driver, it is recommended to use a minimum of 12V, not a 5V power supply, not at 5V, the power supply is connected to ‘5-12V input’, and the power supply is connected to the ‘common cathode’.
5. Length * width * height:about 73 * 51 * 37MM
Controller:Driver
PUL:Pulse negative terminal (PUL-)
DIR:Negative direction (DIR-)
ENA:Enable negative terminal (EN-)
Common anode:Common port (COM or + 5V or PUL + DIR + EN + are connected at the same time)
Common cathode:Common ground (GND)
5-12V input+:The positive end of the 12V power supply is generally empty.It is recommended to use a power supply of more than 15V.
Example:Wiring with the common anode of the driver. If it is driven by 6 signal lines, the + 5V common terminals of the three signals must be connected in parallel to form a line and all connected to the common anode terminal.
Package includes
3 x Controller
Note
1. If you want to use the start or stop function, the ENA enable terminal on the controller must be connected to the driver with a common cathode or a common anode.
2. The forward and reverse rotation and the start and stop of the motor can be controlled by pressing the button.
3. The speed of the motor can be controlled by adjusting the potentiometer to change the frequency.
4. The switch of the motor’s forward / reverse rotation and start / stop is an ordinary switch with self-locking.
5. If you want to connect the switches that control forward and reverse, and open or stop, to the chassis panel, you can refer to the following instructions.
Change the forward and reverse, the start-stop button into a lead-wire switch, see the pin position on the back
1. When the common cathode is connected, the 1 and 3 pins are processed, and the 2, 4, 5, and 6 pins are empty
2. When the common anode is connected, the 1 and 2 pins are processed, and the 3, 4, 5, and 6 pins are empty
The two switches are the same pin lead.
Weight | 0.141 kg |
---|
Customers Also Viewed
3pcs TP5100 Single 4.2V / Dual 8.4V 2A Lithium Battery Charging Board
$11.00Battery Protection ModuleAdd to cartParameterSize:25*17*5mm (length*width*height)Input voltage:DC 5-18V(actual 5-12V is appropriate)Charging status:full and no-load blue light, red during chargingThe voltage setting must be operated in the power-off state, and the switch must be disconnected before switching.Can also be used for white LED constant current drive:set a single lithium drive one, set dual lithium drive two stringsCharacteristic1. Dual / single …
3pcs TP5100 Single 4.2V / Dual 8.4V 2A Lithium Battery Charging BoardRead More
Geekcreit UNO R3 Super Starter Kits Geekcreit for Arduino – products that work with official Arduino boards
$70.34DIY Electronic KitsAdd to cartDescriptionThis super Start kit not only contains UNO R3 control board, but also includes LED diodes, resistors, LCD1602, RFID module, sound module, over than 50 kinds of components and sensors, Which meet your de-mands for different projects either it is simple or complex.Package included5 x White LED5 x Yellow LED5 x Blue LED5 x Green …
1 Layer Stainless Steel Rice Noodle Roll Steamer Rice Roll Maker Steaming Tray
$133.64Laser BoresighterAdd to cartFeature1. 1 Layer with 2 trays.2. Very easy to use.3. Heating quickly.4. 301grade stainless steel.5. Durable laser panel.6. Easy to clean, no rust.7. Edge rounded design, not easy to cut.SpecificationMaterial301grade stainless steelColorSilveryHeating TypeGas steam boiler electric steamerSize33x30x9cm/13’x11.8’x3.5′HOW TO USE1. Mix the flour, water, eggs, minced meat and seasoning into flour paste2. Add water to the …
1 Layer Stainless Steel Rice Noodle Roll Steamer Rice Roll Maker Steaming TrayRead More
10pcs 4 Slots 18650 Battery Holder Plastic Case Storage Box for 4*3.7V 18650 Lithium Battery with 8Pin
$31.83Other Module BoardAdd to cartSpecificationsSupport Model:18650 BatteryShell material:ABS fire, flame retardant, high temperature, color diversity and other materials for choice.Metal spring:carbon steel nickel plating by NCAA salt spray test, stainless steel spring.External:wire, welding pieces, pins, male and female buckle (3.7v button)Terminal:copper nickel platingCorn:nickel plated with coppervPackage Included10 x 4 Slots 18650 Battery Holder Plastic Case Storage Box
CJMCU-633 LSM6DSO 6DOF 3D Gyroscope Attitude Sensor Module 3D Accelerometer 3.3V SPI IIC I2C MIPI I3C SM Serial interface
$22.40Sensor & Detector ModuleAdd to cartFeatureLSM6DSO is an attitude module with 3D digital accelerometer and 3D digital gyroscope. Improve performance at a speed of 0.55 mA in high-performance mode, and enable the always-on low-power function. LSM6DSO supports major OS requirements, provides real, virtual and batch processing of 9 KB sensors for dynamic data batch processing, compatible with AndroidoProduct parameters1. Linear …
5pcs 2 Channel PWM Generator Module Pulse Frequency Duty Cycle Adjustable
$34.82Other Module BoardAdd to cartProduct Introduction1. Operating Voltage:5-30V,support micro USB 5.0V power supply2. Frequency Range:1Hz~150KHz3. Frequency Precision:2%4. Signal Load Capacity:output current is within 8–30mA5. Output Range:default 5V V-pp (can be changed by external power)6. Ambient Temperature:-30 Celsius ~70 Celsius Application Fields1. As square wave generator to generate square wave for experiment development2. Used to drive steeping motor driver’s square …
5pcs 2 Channel PWM Generator Module Pulse Frequency Duty Cycle AdjustableRead More
Accuracy 0.01mm Dial Test Coaxial Centering indicator Centre Finder Milling Tool
$263.24Solar CollectorsAdd to cartDescriptionThe utility model is used for determining the relative position of the inner and outer centers of theworkpiece and the center of the machine tool spindle. It has the care of the shaft rotation, theindicator is always faced with the characteristics of the operator.SpecificationsName:Centering dial test indicatorMaterial:metalColor:silver,blueRange:0-3mmGraduation:0.01mmSize:14x4cmBox size:22x12x6.5cm(LxWxH)Features-Centering dial test indicator is mainly to find …
Accuracy 0.01mm Dial Test Coaxial Centering indicator Centre Finder Milling ToolRead More
Reviews
There are no reviews yet.