5pcs 2.4G DL-LN33 Wireless Networking Board UART Serial Port Module CC2530
$56.58
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Feature
Num.:Parameter:Parameter value
1:Product number:DL-LN33
2:Chip selection:CC2530
3:Working frequency:2400~2450MHz (16 channels total)
4:Communication Interface:UART serial port (supports 13 baud rates, 2400, 4800, 9600, 14400, 19200, 28800, 38400, 57600, 115200, 230400, 125000, 250000, 500000)
5:Self-organizing network hops
6:Single hop transmission distance:70 meters (out of the air, no occlusion test)
7:Number of points that can be accommodated:The typical value is 190. When the network tends to be dense, the number of nodes decreases, and the minimum value is 96.
8:MAX packet length:63Byte (including port address information)
9:Transmission capacity:The transmission rate is higher when only one node sends data
Because the routing information of the transmitted packet occupies a certain bandwidth, the longer the length of each packet, the higher the transmission efficiency.
2400 Bit/s when each package contains 3 bytes of data.
10KBit/s when each package contains 30 bytes of data.
13:MAX send rate:250KBit/s
14:Packet retransmission times:Up to 15 times, at least 5 times when the network load is high
15:Air delay:Single-hop between nodes, less than 10mS
16:Transmit power:4. 5dBm
17:Operating Voltage:2. 5V~3. 6V
18:Working current:Less than 30mA
19:Antenna interface:PCB antenna
Pin Descriptions
Pin name:Pin position:Significance
NoUsed:1, 2,10,11,13:Not used, please keep it empty (empty refers to not connected to any circuit)
TestMode:3:Test mode, when working in normal mode in empty, grounding works in test mode. Please use it empty when the user is using it.
TestTx:4:Enter test information in test mode, which will be output as a controllable IO port when the user uses it.
TestRx:5:Enter test information in test mode, which will be output as a controllable IO port when the user uses it.
Gnd:6, 9,16:Ground
Vcc:7,8:Power supply
BaudReset:12:If this pin is grounded first and then the module is started, the module will force a 115200 default baud rate to operate. In this mode, the baud rate of the module can be read or set. The baud rate read is the baud rate previously set by the module, not 115200. If the baud rate setting is not performed, the module will be restarted again. Work with the previously set baud rate.
Tx:14:Uart output of the module
Rx:15:Uart input of the module
Package includes
5 x Wireless Networking Board
Weight | 0.03 kg |
---|
Customers Also Viewed
5pcs TS-300B Turbidity Sensor Detection Module Water Quality Tester Washing Machine Turbidity Transduce
$43.93Sensor & Detector ModuleAdd to cartPrincipleTurbidity sensor TS-300B measures the turbidity (counter of suspended matter) in the wash water. Based on the optical principle, the sensor uses the light-emitting diode and phototransistor to receive the specific wavelength to measure the opacity or other substances of dirty water. concentration. By using phototransistors and light-emitting diodes, the light emitted by the sensor …
3Pcs USB Fan Speed Controller Module Reducing Noise Multi-stall Adjustment Governor DC 4-12V
$20.74Motor PWM Speed ControllerAdd to cartFeatures– USB Fan Air Conditioner – Strong winds and weak wind adjust freely – Stepless Speed Regulation – Suitable for the very common 5.0V USB fan on the market Regulation PrincipleThe non-adjustable fan is a 5V direct fan motor,while the two-stall fan is the interior has a step-up circuit board,when placed in the second gear,the …
5pcs JDY-08 BLE bluetooth 4.0 Serial Port Wireless Module Low Power Master-slave Support Airsync i Beacon
$45.12Smart ModuleAdd to cartFeaturesJDY-08 transparent transmission module is based on bluetooth 4.0 protocol standard, working frequency range is 2.4GHZ range, modulation mode is GFSK, large transmission power is 0db, large transmission distance is 80 meters, TICC2541 chip design is adopted, and users can modify device name by AT command. , service UUID, transmit power, pairing password and other …
ADC Module ADS1100 for Analog Signal Capture Converter Compatible M5StickC ESP32 Mini IoT Development Board Fi
$14.74Converter BoardAdd to cartnull Description ADC_HAT is another type of C-HAT specifically design for M5StickC controller. Same as ADC unit, this is an ADC converter component for stickc. Packed with an ADC converter chip ADS1100, which is a fully differential, 16-bit, self-calibrating, A/D converter. Extremely easy to design with and configure, the ADS1100 allows you to obtain precise …
5pcs Mini MP1584EN DC-DC BUCK Adjustable Step Down Module 4.5V-28V input 0.8V-20V Output
$8.94Power Supply ModuleAdd to cartSpecificationsModel:MP1584Name:DC-DC step-down moduleInput Voltage:4.5V ~ 28VOutput voltage:0.8V ~ 20VOutput Current:3A (Max)Conversion efficiency:96% (maximum)Output RippleSwitching frequency:1.5MHz (highest) typically 1MHzOperating Temperature:-45°C ~ +85°CSize:22mm * 17mm (L * W )Application areas:DIY mobile power, monitor power supply, power buggies, camera power supply, car power, communications equipment supply,etc.Packge included5 x Step Down Module
LILYGO TTGO T-Koala ESP32 WiFi and bluetooth Module 4MB Development Board Based on ESP32-WROOM-32 Micro USB
$26.23Smart ModuleAdd to cartFeatureEspressif official ESP32-WROOM-32 moduleLatest ESP32 version:REV14MB FLASHLithium battery interface, 500mA maximum charging currentCompatible with , MicroPythonDefault firmware:latest MicroPythoTechnical specificationsMicrocontroller:ESP-32Board power supply:(USB) 5VSupport battery:Lipo Battery 3.7VWorking voltage:3.3VFlash:4 MbytesLength:78 mmWidth:27 mmWeight:7.8 gramsPackage includes1 x ESP32 WiFi&bluetooth Broad2 x Pin
Reviews
There are no reviews yet.