5pcs 2.4G DL-LN33 Wireless Networking Board UART Serial Port Module CC2530
$56.58
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Feature
Num.:Parameter:Parameter value
1:Product number:DL-LN33
2:Chip selection:CC2530
3:Working frequency:2400~2450MHz (16 channels total)
4:Communication Interface:UART serial port (supports 13 baud rates, 2400, 4800, 9600, 14400, 19200, 28800, 38400, 57600, 115200, 230400, 125000, 250000, 500000)
5:Self-organizing network hops
6:Single hop transmission distance:70 meters (out of the air, no occlusion test)
7:Number of points that can be accommodated:The typical value is 190. When the network tends to be dense, the number of nodes decreases, and the minimum value is 96.
8:MAX packet length:63Byte (including port address information)
9:Transmission capacity:The transmission rate is higher when only one node sends data
Because the routing information of the transmitted packet occupies a certain bandwidth, the longer the length of each packet, the higher the transmission efficiency.
2400 Bit/s when each package contains 3 bytes of data.
10KBit/s when each package contains 30 bytes of data.
13:MAX send rate:250KBit/s
14:Packet retransmission times:Up to 15 times, at least 5 times when the network load is high
15:Air delay:Single-hop between nodes, less than 10mS
16:Transmit power:4. 5dBm
17:Operating Voltage:2. 5V~3. 6V
18:Working current:Less than 30mA
19:Antenna interface:PCB antenna
Pin Descriptions
Pin name:Pin position:Significance
NoUsed:1, 2,10,11,13:Not used, please keep it empty (empty refers to not connected to any circuit)
TestMode:3:Test mode, when working in normal mode in empty, grounding works in test mode. Please use it empty when the user is using it.
TestTx:4:Enter test information in test mode, which will be output as a controllable IO port when the user uses it.
TestRx:5:Enter test information in test mode, which will be output as a controllable IO port when the user uses it.
Gnd:6, 9,16:Ground
Vcc:7,8:Power supply
BaudReset:12:If this pin is grounded first and then the module is started, the module will force a 115200 default baud rate to operate. In this mode, the baud rate of the module can be read or set. The baud rate read is the baud rate previously set by the module, not 115200. If the baud rate setting is not performed, the module will be restarted again. Work with the previously set baud rate.
Tx:14:Uart output of the module
Rx:15:Uart input of the module
Package includes
5 x Wireless Networking Board
Weight | 0.03 kg |
---|
Customers Also Viewed
1.8 inch LCD TFT Display Module with PCB Backplane 128X160 SPI Serial Port
$15.30Display ScreenAdd to cartFeatureResolution:128X160Driver IC:ILI9163/ST7735Module with regulator IC supports 3.2V/5V power supplyWith SD card holder, you can do experiments like digital photo frameThe module reserves the Nokia3310/5110 interface, supports the 1602 interface, and directly plugs in and out.IO for streamlined wiring:(only 3 IOs after optimization)1. RST– directly connected to the microcontroller reset signal terminal, this IO can save2. …
1.8 inch LCD TFT Display Module with PCB Backplane 128X160 SPI Serial PortRead More
USB Boost 5V to 1.2V 3.3V 6V 9V 12V 24V Power Supply Module Adjustable Voltage
$10.92Test & Measuring ModuleAdd to cartFeatureInput voltage:3.5V-12VOutput voltage:1.2-24VOutput PowerOutput voltage 1.2V-2V, used within 2WOutput voltage 2V-20V, used within 3WOutput voltage 20V-24V, used within 2.5WOutput power = output voltage x output currentNote:This product is not a high power supply, please use it within the power range.Package includes1 x Power Module
10pcs IR LED infrared Light Board for CCTV Camera Night Vision 30-40M 6*Array LED White 2.5W DC12V
$26.76LED BoardAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.Features– High power / Spot Light / Infrared IR LED boards for CCTV cameras night vision.– Driven board & CDS sensor included.– Power supply exceeds DC13V may greatly reduce the LEDs operating …
2500Pcs 2.54mm XH2.54 2p 3p 4 Pin Connector Plug+Straight Needle+Terminal Socket Header Wire Adaptor
$56.09Electronic Accessories & SuppliesAdd to cartDescription2pin = 200 sets3pin = 200 sets4pin = 100 setsPin Connector Terminal:1500 pcs (Please allow 5% deviation)Package included10 x Connector plug kit with box
19PCS DIY Resin Casting Molds Silicone Jewelry Pendant Craft Making Mould Tool
$58.71ConnectorsAdd to cartSpecificationName:Resin Casting MoldsMaterial:SiliconeColor:TransparentFeature-Flexible, resistant to tearing.-Easy to use and clean.-Easy to release.-Durable in use.-Great for jewelry pendant making, earrings, soap making, chocolate making, sugarpaste making.-You can also add some flowers, glitter, colors to make your own art craft gift.Package Included9x Resin Casting Molds (Mold only, NO accessories)10x Wood Sticks
4G Cat.1 LTE IoT Module Full Netcom Ca-01 4G Development Board
$98.40Motherboard & Development BoardAdd to cartDocumentsProduct specification:Click here to openSchematic diagram:Click here to openat_instruction_set_CN_ONLY:Click here to open (If you mind about this, please don’t buy)hardware_info:Click here to openserial_tool:Click here to openFeature:Ca-01 development board characteristics and detailed parametersCommunication system:4GApplicable frequency band:LTE-FDD:B1/B3/B5/B8LTE-TDD:B34/B38/B39/B40/B41General characteristics:3GPP E-UTRA Release 13Band width:1.4/3/5/10/15/20MHZModule size:24.0mm x 24.0mm x 2.3mmPackage method:stamp hole + LGAModule weight:about 2.6gPower supply voltage:3.3V~4.3V, typical value …
4G Cat.1 LTE IoT Module Full Netcom Ca-01 4G Development BoardRead More
Reviews
There are no reviews yet.