10pcs 2.4G DL-LN33 Wireless Networking Board UART Serial Port Module CC2530
$108.53
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Feature
Num.:Parameter:Parameter value
1:Product number:DL-LN33
2:Chip selection:CC2530
3:Working frequency:2400~2450MHz (16 channels total)
4:Communication Interface:UART serial port (supports 13 baud rates, 2400, 4800, 9600, 14400, 19200, 28800, 38400, 57600, 115200, 230400, 125000, 250000, 500000)
5:Self-organizing network hops
6:Single hop transmission distance:70 meters (out of the air, no occlusion test)
7:Number of points that can be accommodated:The typical value is 190. When the network tends to be dense, the number of nodes decreases, and the minimum value is 96.
8:MAX packet length:63Byte (including port address information)
9:Transmission capacity:The transmission rate is higher when only one node sends data
Because the routing information of the transmitted packet occupies a certain bandwidth, the longer the length of each packet, the higher the transmission efficiency.
2400 Bit/s when each package contains 3 bytes of data.
10KBit/s when each package contains 30 bytes of data.
13:MAX send rate:250KBit/s
14:Packet retransmission times:Up to 15 times, at least 5 times when the network load is high
15:Air delay:Single-hop between nodes, less than 10mS
16:Transmit power:4. 5dBm
17:Operating Voltage:2. 5V~3. 6V
18:Working current:Less than 30mA
19:Antenna interface:PCB antenna
Pin Descriptions
Pin name:Pin position:Significance
NoUsed:1, 2,10,11,13:Not used, please keep it empty (empty refers to not connected to any circuit)
TestMode:3:Test mode, when working in normal mode in empty, grounding works in test mode. Please use it empty when the user is using it.
TestTx:4:Enter test information in test mode, which will be output as a controllable IO port when the user uses it.
TestRx:5:Enter test information in test mode, which will be output as a controllable IO port when the user uses it.
Gnd:6, 9,16:Ground
Vcc:7,8:Power supply
BaudReset:12:If this pin is grounded first and then the module is started, the module will force a 115200 default baud rate to operate. In this mode, the baud rate of the module can be read or set. The baud rate read is the baud rate previously set by the module, not 115200. If the baud rate setting is not performed, the module will be restarted again. Work with the previously set baud rate.
Tx:14:Uart output of the module
Rx:15:Uart input of the module
Package includes
10 x Wireless Networking Board
Weight | 0.06 kg |
---|
Customers Also Viewed
LED Cool Light Egg Candler Tester Ultra Bright Pocket Poultry Egg Lamp incubator
$56.69Switch AccessoriesAdd to cartFeatures– Made of high quality ABS material, insulating, stable and durable.– LED lamp head, high power, strong light source, can clearly detect the hatching of eggs.– Using high-quality materials, safe and durable, with buttons that are easy to open and close.– Suitable for hatching eggs, but also for children and students to learn the process …
LED Cool Light Egg Candler Tester Ultra Bright Pocket Poultry Egg Lamp incubatorRead More
5pcs 2 Channel PWM Generator Module Pulse Frequency Duty Cycle Adjustable
$34.82Other Module BoardAdd to cartProduct Introduction1. Operating Voltage:5-30V,support micro USB 5.0V power supply2. Frequency Range:1Hz~150KHz3. Frequency Precision:2%4. Signal Load Capacity:output current is within 8–30mA5. Output Range:default 5V V-pp (can be changed by external power)6. Ambient Temperature:-30 Celsius ~70 Celsius Application Fields1. As square wave generator to generate square wave for experiment development2. Used to drive steeping motor driver’s square …
5pcs 2 Channel PWM Generator Module Pulse Frequency Duty Cycle AdjustableRead More
3.7V Lithium Battery 4 Paragraph Power indicator Module
$4.36Test & Measuring ModuleAdd to cartDescription1, onboard high precision voltage detection chip and power supply voltage chip2, onboard four power indicator LED lights, three kinds of color display, red, yellow, yellow, green,representing 20%, 50%, 80%, 100% of the battery3, set aside a battery testing interface and two positioning hole4, PCB size:22.2 (mm) x17.2 (mm)Package included1 x 3.7V Lithium Battery 4 …
3.7V Lithium Battery 4 Paragraph Power indicator ModuleRead More
YAHBOOM High-quality T-shape Expansion Board + 40Pin GPIO Flat Rainbow Ribbon Cable for Raspberry 4B/3B+/ZERO/W
$10.21Raspberry Pi & Orange PiAdd to cartDescriptionThis high-quality T-shape expansion board allows you to connect the Raspberry Pi GPIO port for breadboard experiments. We will provide a 40Pin soft cable for you to connect the Raspberry Pi board to the breadboard.FeaturesSpecifically designed for Raspberry Pi 4B/3B, Raspberry Pi 2B, Raspberry Pi 1B+, Raspberry pi 1A+, Raspberry Pi zero W, Raspberry Pi …
10pcs LM3915 10-segment Audio Level indicator Kit Electronic Soldering Training experiment DIY Parts
$33.89DIY Electronic KitsAdd to cartFeatrurePower supply:DC9-12VPCB size:62*27mm1 audio cable is needed. One end is subtracted and connected to the audio input port. The red cable is connected to AUDIO +, the green cable is connected to ADUIO-, and the blue cable is subtracted, do not need to solder.Package included10 x LM3915 10-segment Audio Level Indicator Kit
10pcs 40x40mm thermoelectric Power Generator Peltier Module TEG High Temperature 150 Degree
$55.12Electronic Accessories & SuppliesAdd to cartFeatureColding side posts with the wordsHeating side is emptyRed wire to positive, black wire to the negative, it generate electricity when the temperature difference happenedSpecificationModel:SP1848-27145 Color:whiteLead Length:about 30CMSize:40MM x 40MM x 3.4MM20 degree temperature difference:open-circuit voltage 0.97V, generated current:225MA40 degree temperature difference:open circuit voltage 1.8V, generated current:368MA60 degree temperature difference:open circuit voltage 2.4V, generated current:469MA80 …
10pcs 40x40mm thermoelectric Power Generator Peltier Module TEG High Temperature 150 DegreeRead More
Reviews
There are no reviews yet.