Automatic Irrigation Pumping Water Pump Module Soil Moisture Humidity Detection Sensor Module
$10.61
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
This board can roughly measure the humidity and determine the switch of the watering equipment according to the humidity. The sensitivity can be roughly adjusted with a potentiometer.
You can use a power bank (5V DC) as the power source or use 4 X AA battery boxes and install 4 batteries for power supply.
About the test
Test relay module 1:Connect the relay module vcc 5 V to ground, ground, and then connect to ground. If the relay is empty, the relay will recover and you can hear the sound of ‘card’;
2. Test the soil moisture sensor module:Connect the fork probe and the transmitter module with two DuPont cables, and ground the transmitter module vcc 5 V and gnd. The red power indicator light always stays on, while the green (blue) indicator light will flash once. Put the fork probe directly into the water, the green (blue) indicator light will be on;
3. Connect the red wire of the pump to 5 V and the black wire to ground, and the pump will start to work. Remember:the test can be performed for 1 second. Because it cannot be exposed to the air for a long time.
4. Assemble according to the schematic diagram.
Note
1. This product can be free of welding, but you need to strip the wire, twist the copper wire together, and protect it with black tape;
2. The water pump cannot be operated in the air for a long time;
3. The system is connected and powered on, and the water pump works all the time. It is correct. Because the probe cannot detect the humidity in the air, the water pump works all the time. There is no problem if it is installed correctly in the flowerpot.
4.Do not pour water directly on the probe. Many people don’t know this. When the humidity is high, it will rust and break.
Package Included
1 x Relay module
1 x Soil moisture module
1 x Horizontal water pump
1 x Battery holder (without batteries)
1 x USB
1 x 50cm silicone tube
10 x Dupont line female to female
Weight | 0.064 kg |
---|
Customers Also Viewed
28.35ct 20x15mm Purple Oval Elliptical Cut Gemstone VVS AAA Jewelry Loose Gems Decorations
$20.24Lab Clamp & StandAdd to cartSpecificationsMaterial:ZirconColor:PurpleSize:20x15mmWeight:28.35ctClarity:VVS AAAShape:OvalFeatures– Transparent, bright;– Color is bright and the purity is positive;– Wide range of use;– Application for jewelry.Package Included1 Pcs x Purple Oval Cut Gemstone
5pcs CJMCU-250E BMA250E Sensor Module 3-axis Low G Acceleration Sensor Triaxial Accelerometer SPI IIC interface
$32.02Sensor & Detector ModuleAdd to cartFeatureThe BMA250E is a triaxial, low-g acceleration sensor with digital output for consumer applications. It allows measurements of acceleration in three perpendicular axes. An evaluation circuitry (ASIC) converts the output of a micromechanical acceleration-sensing structure(MEMS) that works according to the differential capacitance principle.Package and interfaces of the BMA250E have been defined to match a multitude …
JoyC Rocker Sensor Switch Module STM32F030F4 Control Chip Game Handle I2C Wireless Joystick Device
$54.05Motherboard & Development BoardAdd to cartDescriptionJoyC is a rocker module designed for the M5StickC.It supports two-hand operation. Embedded STM32F030F4 main control chip, using I2C communication protocol and host M5StickC for data transmission. The ran ge of the joystick is 0~200, there are 12 RGB LEDs under the left and right joysticks, and the bottom of the joystick is equipped with …
600-6000MHz UWB WiFi Ultra-wideband Log Periodic Antenna
$32.00RF amplifierAdd to cartSpecification1. Antenna frequency:600-6000MHz2. Antenna standing wave:less than 2 (typical value)3. Antenna polarization:directional linear polarization4. Antenna gain:6-7dB5. Power capacity:50W6. Dimensions:20≠20CM7. Weight:74 g8. Connector form:SMA-K (standard female, outer screw and inner hole)Package included1 x Antenna
Reviews
There are no reviews yet.