3pcs Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology Small Production Kit
$10.56
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
The purpose of the experiment
1. Understand and recognize the light-emitting diodes and illuminate the light-emitting diodes (LEDs);
2. Understand the role of understanding resistance, series and parallel resistance;
3. Understand the self-locking switch;
4. Understand and recognize adjustable resistors and use adjustable resistors;
Experimental steps
Step 1:The long leg of the light-emitting diode (LED) is the positive pole, and the short leg is the negative pole. First, the long wire of the LED is connected to the black wire (negative electrode) of the battery case, and the short leg of the LED is connected to the red wire (positive electrode) of the battery case. At this time, the light emitting diode (LED) is not lit. Then send it over again, let the long leg of the LED connect to the red line of the battery box, and the short leg of the LED is connected to the black line of the battery box. At this time, the LED lights up, indicating that the LED is in one-way operation and the single-pass characteristic of the diode .
Step 2:In the circuit of the experimental step 1, a resistor of 220 ohms is inserted in series, and the brightness of the LED lamp is lowered, and the resistance hinders the current.
Step 3:Connect a 220 ohm resistor in parallel with the resistance in the circuit of the experimental board 2. The brightness of the LED is increased, indicating that the total resistance of the resistor in the circuit is reduced after the resistors are connected in parallel.
Step 4:Change the two resistors of the experimental step 3 from parallel to series. After the series connection, the brightness of the LED lamp is the lowest. After the series connection of the resistors, the total resistance of the resistor in the circuit increases.
Step 5:Replace the original resistor with a potentiometer. The potentiometer has 3 feet, and the resistance of pins 1 and 3 is fixed. The resistance of pins 1 and 2, 2 feet and 3 feet can be changed by adjusting the potentiometer knob. When experimenting, you can pick up 2 of them. The foot has to experiment many times, adjust the potentiometer knob to observe the change of LED brightness, so that you can fully understand the potentiometer.
Step 6:Know the self-locking. Press and wait for the light to be on, then press the light to turn off.
Package included
3 x DIY LED Dimming Lights Technology Small Production Kit
Weight | 0.081 kg |
---|
Customers Also Viewed
R103C 6GHz 5.8G Broadband Directional Antenna High Gain ads-b UAV Image Transmission Antenna
$30.90RF amplifierAdd to cartDescriptionThis directional antenna is suitable for directional radio signal transmission and reception signal source reconnaissance lateral, broadband signal testing, etc.The antenna covers the common frequencies of mobile phone communication, UWB positioning module and Wifi and other radio frequency unitsFrequency range:850MHz-6GHzDimensions:22*15CMPolarization method:linear polarizationRated gain:7dbiReturn loss:10DBPower:5WWeight:110gPackage included1 x Broadband Directional Antenna
3Pcs HY-SRF05 Ultrasonic Distance Sensor Module Measuring Sensor Module
$13.93Sensor & Detector ModuleAdd to cart3Pcs HY-SRF05 Ultrasonic Distance Sensor Module Measuring Sensor ModuleDescriptionThis module performance is stable, measure the distance accurately. Module precision, blind spots (2cm) super close.SpecificationInput voltage:5V DCQuiescent currentOutput level(high):5VOutput level(low):0VInduction angleDetection distance:2cm – 450cmAccuracy:up to 0.3cmBlind spots:2cmPackage included3 x HY-SRF05 ultrasonic distance sensor module
AC Contactor AC220V Coil 32A 3-Phase 1NO 50/60Hz Motor Starter Relay LC1 D1810
$48.59RelaysAdd to cartDescriptionAC Contactor AC220V Coil 32A 3-Phase 1NO 50/60Hz Motor Starter Relay LC1 D1810Features1.High strength PC flame retardancy,AC220V copper coil.2.A contactor (motor starter) is a high capacity relay that has built-in auxiliary contact to work with momentary push buttons.3.It is versatile and is often used to control a motor or as a main power switch, sometimes …
AC Contactor AC220V Coil 32A 3-Phase 1NO 50/60Hz Motor Starter Relay LC1 D1810Read More
BESTEP 1 Channel 5V Low Level Solid State Relay Module with Fuse 250V2A for Auduino
$6.55Relay ModuleAdd to cartDescription1. 5V solid state relay 240V 2A, output with resistance fuse 240V 2A.2. Size:25*34*25 (length * width * height) Net weight:13g3. Input power:5V DC (160MA)4. Input control signal voltage:(0-1.5V state low level relay ON) (2.5-5V state high level relay OFF)5. The blue KF301 terminal is more convenient to connect to the control line.Module interfaceInput sectionDC+:Connect …
BESTEP 1 Channel 5V Low Level Solid State Relay Module with Fuse 250V2A for AuduinoRead More
ZL-7903A Multifunctional Automatic Temperature and Humidity incubator Controller XM-18 100-240V AC with with ZL-SHr05J Sensor
$107.15Test & Measuring ModuleAdd to cart>>>Manual:Click here to openFeatureZL-7903A is an industrial intelligent temperature and humidity controller. Optional external SSR to realize bigger heatingpower rate, and with optional temperature PID control. With touch button and big size LCD display, convenient to operate,easy to set up. Applicable for control of incubator, climate chamber, warehouse, and so on.Main Function1. Ventilation fan control2. …
Reviews
There are no reviews yet.