20pcs Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology Small Production Kit
$54.99
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
The purpose of the experiment
1. Understand and recognize the light-emitting diodes and illuminate the light-emitting diodes (LEDs);
2. Understand the role of understanding resistance, series and parallel resistance;
3. Understand the self-locking switch;
4. Understand and recognize adjustable resistors and use adjustable resistors;
Experimental steps
Step 1:The long leg of the light-emitting diode (LED) is the positive pole, and the short leg is the negative pole. First, the long wire of the LED is connected to the black wire (negative electrode) of the battery case, and the short leg of the LED is connected to the red wire (positive electrode) of the battery case. At this time, the light emitting diode (LED) is not lit. Then send it over again, let the long leg of the LED connect to the red line of the battery box, and the short leg of the LED is connected to the black line of the battery box. At this time, the LED lights up, indicating that the LED is in one-way operation and the single-pass characteristic of the diode .
Step 2:In the circuit of the experimental step 1, a resistor of 220 ohms is inserted in series, and the brightness of the LED lamp is lowered, and the resistance hinders the current.
Step 3:Connect a 220 ohm resistor in parallel with the resistance in the circuit of the experimental board 2. The brightness of the LED is increased, indicating that the total resistance of the resistor in the circuit is reduced after the resistors are connected in parallel.
Step 4:Change the two resistors of the experimental step 3 from parallel to series. After the series connection, the brightness of the LED lamp is the lowest. After the series connection of the resistors, the total resistance of the resistor in the circuit increases.
Step 5:Replace the original resistor with a potentiometer. The potentiometer has 3 feet, and the resistance of pins 1 and 3 is fixed. The resistance of pins 1 and 2, 2 feet and 3 feet can be changed by adjusting the potentiometer knob. When experimenting, you can pick up 2 of them. The foot has to experiment many times, adjust the potentiometer knob to observe the change of LED brightness, so that you can fully understand the potentiometer.
Step 6:Know the self-locking. Press and wait for the light to be on, then press the light to turn off.
Package included
20 x DIY LED Dimming Lights Technology Small Production Kit
Weight | 0.54 kg |
---|
Customers Also Viewed
5pcs DD2712SA 3.5A Mini 5V-27V to 3.7V DC DC Step Down Buck Power Converter Module Voltage Regulator
$22.52Boost & Buck ModuleAdd to cartDescriptionInput voltage:5-27VOutput voltage:5V Maximum output current:2.5AShort time maximum output current:3.5A Quiescent current:about 250uAWorking frequency:900KHz.Working efficiency:77-92% Size:25 x 15 x 6.3 mmOvertemperature shutdown, Under-Voltage Lockout (UVLO), BS-voltage protection, and short circuit protection.Note1. Input voltage can not be greater than the maximum input range.2. Output power can not be greater than the maximum load for a long …
1080P 5MP 160 Fish Eye Surveillance Camera Module for Raspberry Pi with IR Night Vision
$34.43Raspberry Pi & Orange PiAdd to cartFeatures– This is the new version, can replace the infrared lamp or white fill light, the effect is great.– The Raspberry Pi Camera Board Features a 5 million pixels– And also supports 1080p @ 30 fps, 720p @ 60 fps and 640*480p 60/90 video recording.– OmniVision 5647 sensor in a fixed focus module.– The module …
1080P 5MP 160 Fish Eye Surveillance Camera Module for Raspberry Pi with IR Night VisionRead More
STM32H743VIT6 STM32H7 Development Board STM32 System Board M7 Core Board TFT interface with USB Cable
$58.95Motherboard & Development BoardAdd to cart>>>STM32H750VBT6 Manual:Click here to open>>>STM32H743VIT6 Manual:Click here to openhttp://myosuploads3.hobbyant.com/products/20200410/20200410051631STM32H750HAL-1909.rarhttp://myosuploads3.hobbyant.com/products/20200410/20200410020657STM32H743HAL-1909.rarSpecificationsFrequency:400M (M7 core)Package:LQFP100RAM:1024KBFlash:H750VB:128KB H743VI:2048KB (2M)OLED interface – plug and play, support 0.96 inch / 1.3 inch OLED TFT liquid crystal interfaceConnect 1.3 inch HD full color LCDConnect 2.0 inch HD full color LCD Data storage:W25Q64 (QSPI driver)High speed crystal:25MHZLow frequency crystal:32.768KPower + programmable LED lights2 users and …
2.5 inch 60mm LED Turbo Boost Gauge Vacuum Press Pressure Bar Dials Meter for Car Truck
$99.21Switch AccessoriesAdd to cartSpecifications Material:Aluminum+ABS+Acrylic Power:DC(10-15V) 12V Professional Reads Range:-1~2 BAR Light Colour:White + Red Diameter:2.5 Inch /60mm Packing Size:15 x 8 x 11cm Features 270 degree sweep. Illuminated red needle display. LED Backlight display between white and red light are switched by the button. When the pressure alarm, peak light becomes red, the pressure alarm point can …
2.5 inch 60mm LED Turbo Boost Gauge Vacuum Press Pressure Bar Dials Meter for Car TruckRead More
5pcs JDY-16 bluetooth 4.2 Module Low Power High Speed Data Transfer Mode BLE Module
$28.46Other Module BoardAdd to cartDescriptionJDY-16 Version supports(WeChat, APP, Android) Transparent, IO, RTC, PWM and other functions1.BLE high speed transparent transmission supports 8K Bytes rate communication2.Send and receive data without byte limit, support 115200 baud rate often send and receive data3.Support 3 modes of work4.Support(serial port, IO, APP) sleep wake up5.Support Wechat Airsync, Wechat applet and APP communication6.Support 4 channel …
5pcs JDY-16 bluetooth 4.2 Module Low Power High Speed Data Transfer Mode BLE ModuleRead More
Reviews
There are no reviews yet.