10pcs Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology Small Production Kit
$29.32
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
The purpose of the experiment
1. Understand and recognize the light-emitting diodes and illuminate the light-emitting diodes (LEDs);
2. Understand the role of understanding resistance, series and parallel resistance;
3. Understand the self-locking switch;
4. Understand and recognize adjustable resistors and use adjustable resistors;
Experimental steps
Step 1:The long leg of the light-emitting diode (LED) is the positive pole, and the short leg is the negative pole. First, the long wire of the LED is connected to the black wire (negative electrode) of the battery case, and the short leg of the LED is connected to the red wire (positive electrode) of the battery case. At this time, the light emitting diode (LED) is not lit. Then send it over again, let the long leg of the LED connect to the red line of the battery box, and the short leg of the LED is connected to the black line of the battery box. At this time, the LED lights up, indicating that the LED is in one-way operation and the single-pass characteristic of the diode .
Step 2:In the circuit of the experimental step 1, a resistor of 220 ohms is inserted in series, and the brightness of the LED lamp is lowered, and the resistance hinders the current.
Step 3:Connect a 220 ohm resistor in parallel with the resistance in the circuit of the experimental board 2. The brightness of the LED is increased, indicating that the total resistance of the resistor in the circuit is reduced after the resistors are connected in parallel.
Step 4:Change the two resistors of the experimental step 3 from parallel to series. After the series connection, the brightness of the LED lamp is the lowest. After the series connection of the resistors, the total resistance of the resistor in the circuit increases.
Step 5:Replace the original resistor with a potentiometer. The potentiometer has 3 feet, and the resistance of pins 1 and 3 is fixed. The resistance of pins 1 and 2, 2 feet and 3 feet can be changed by adjusting the potentiometer knob. When experimenting, you can pick up 2 of them. The foot has to experiment many times, adjust the potentiometer knob to observe the change of LED brightness, so that you can fully understand the potentiometer.
Step 6:Know the self-locking. Press and wait for the light to be on, then press the light to turn off.
Package included
10 x DIY LED Dimming Lights Technology Small Production Kit
Weight | 0.27 kg |
---|
Customers Also Viewed
Geekwrom HD 3.5 inch TFT Display Shield 800×480 for Raspberry Pi 3B 2B + Acrylic Matching Case Kit
$121.30Raspberry Pi & Orange PiAdd to cartGeekwrom HD 3.5 Inch TFT Display Shield 800×480 For Raspberry Pi 3B 2B + Acrylic Matching Case KitHD 3.5 Inch TFT Display Shield 800×480 For Raspberry Pi 3B 2BFeatures– Demensions:85mm*56.5mm;– Resolution:800 x 480, 3.5 inch;– 267ppi High PPI display screen;– 11ms High Response Time(more than 60 fps);– 160° Wide Viewing Angle;– 900:1 High Contrast Ratio;– …
intelligent Screen Solar Pure Sine Wave Power inverter 1200W-6000W DC To AC 110V 120V Converter
$121.49InvertersAdd to cartWatt 1200W Voltage 12V Type Single digital display / Watt 2200W Voltage 12V Type Single digital display / Watt 3000W Voltage 12V Type Single digital display / Watt 3000W Voltage 24V Type Single digital display / Watt 3000W Voltage 48V Type Single digital displ
500W Aquarium Submersible Stainless Steel Heating Rod Adjustable Heater
$48.59Solar CollectorsAdd to cartDescriptionMaterial:Stainless SteelColor:SilverPlug:US PlugVoltage:220-240V 50HzWattage:500WTemperature range:16-32°CCable Length:120cm/47.24inch(appr.)Heating Rod Length:41cm/16.14inch(appr.)FeaturesMade of stainless steel material, anti-rust, useful and durable.Double insulation & waterproof.Keep the water temperature steady.Suitable for aquarium:500L (for reference only).Simple adjustment and easy to read temperature indicator.Easy to install with 2 strong suckers (mounting distance of 2 suckers is about 9.5cm).Adjustment knob allows you to adjust the …
500W Aquarium Submersible Stainless Steel Heating Rod Adjustable HeaterRead More
5pcs JoyStick Module Shield 2.54mm 5 pin Biaxial Buttons Rocker for PS2 Joystick Game Controller Sensor
$14.30Other Module BoardAdd to cartFeaturejoystick joysticks standard interface module electronic building blocks and 2.54mm pin interface leads.Phillips is a two-way rocker 10K resistor, with the joystick in a different direction, tap the resistance vary. This module uses a 5V supply, the original state X, Y readout voltage of 2.5V or so, when pressed with the direction of the arrow, …
4Pcs Geekcreit Ultrasonic Module HC-SR04 Distance Measuring Ranging Transducers Sensor DC 5V 2-450cm
$9.83Sensor & Detector ModuleAdd to cartDescriptionWorking Voltage:5V(DC)Static Current:Less than 2mA.Output Signal:Electric frequency signal, high level 5V, low level 0V.Sensor Angle:Not more than 15 degrees.Detection Distance:2cm-450cm.High Precision:Up to 0.3cmInput Trigger Signal:10us TTL impulseSignal:output TTL PWL signalMode of connectionVCCtrig(T)ech0(R)GNDUse MethodSupply module with 5V, the output will be 5V while obstacle in range, or 0V if not.The out pin of this module is …
1MHz-700MHZ 3.2W HF VHF UHF FM Transmitter RF Power Amplifier for Ham Radio
$50.29RF amplifierAdd to cartApplicationBroadband RF power amplifier for all types of wireless applications, FM shortwave radios remote control toys, digital radio, etc., enter 1 milliwatt (0DBM) maximum output of 3 watts, 15V voltage supply, broadband work 1MHZ to 700MHZ can be work. As a result of well-designed, low end that can reach 35DBM (3W), at 500M, the output …
1MHz-700MHZ 3.2W HF VHF UHF FM Transmitter RF Power Amplifier for Ham RadioRead More
Reviews
There are no reviews yet.