10pcs Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology Small Production Kit
$29.32
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
The purpose of the experiment
1. Understand and recognize the light-emitting diodes and illuminate the light-emitting diodes (LEDs);
2. Understand the role of understanding resistance, series and parallel resistance;
3. Understand the self-locking switch;
4. Understand and recognize adjustable resistors and use adjustable resistors;
Experimental steps
Step 1:The long leg of the light-emitting diode (LED) is the positive pole, and the short leg is the negative pole. First, the long wire of the LED is connected to the black wire (negative electrode) of the battery case, and the short leg of the LED is connected to the red wire (positive electrode) of the battery case. At this time, the light emitting diode (LED) is not lit. Then send it over again, let the long leg of the LED connect to the red line of the battery box, and the short leg of the LED is connected to the black line of the battery box. At this time, the LED lights up, indicating that the LED is in one-way operation and the single-pass characteristic of the diode .
Step 2:In the circuit of the experimental step 1, a resistor of 220 ohms is inserted in series, and the brightness of the LED lamp is lowered, and the resistance hinders the current.
Step 3:Connect a 220 ohm resistor in parallel with the resistance in the circuit of the experimental board 2. The brightness of the LED is increased, indicating that the total resistance of the resistor in the circuit is reduced after the resistors are connected in parallel.
Step 4:Change the two resistors of the experimental step 3 from parallel to series. After the series connection, the brightness of the LED lamp is the lowest. After the series connection of the resistors, the total resistance of the resistor in the circuit increases.
Step 5:Replace the original resistor with a potentiometer. The potentiometer has 3 feet, and the resistance of pins 1 and 3 is fixed. The resistance of pins 1 and 2, 2 feet and 3 feet can be changed by adjusting the potentiometer knob. When experimenting, you can pick up 2 of them. The foot has to experiment many times, adjust the potentiometer knob to observe the change of LED brightness, so that you can fully understand the potentiometer.
Step 6:Know the self-locking. Press and wait for the light to be on, then press the light to turn off.
Package included
10 x DIY LED Dimming Lights Technology Small Production Kit
Weight | 0.27 kg |
---|
Customers Also Viewed
3Pcs CJMCU-219 INA219 I2C Bi-directional Current / Power Monitor Sensor Module
$24.62Sensor & Detector ModuleAdd to cart3Pcs CJMCU-219 INA219 I2C Bi-directional Current / Power Monitor Sensor ModuleDescriptionCJMCU-219 module is a with I2C interface Bidirectional current / power monitor integrated circuit (IC), and further expand the energy-saving electronic products TI camp. INA219 with the industry’s highest accuracy and smallest size, not only to monitor the voltage drop across a shunt resistor on …
3Pcs CJMCU-219 INA219 I2C Bi-directional Current / Power Monitor Sensor ModuleRead More
GDCPH 16V83F Super Farah Capacitor Automotive Electronic Rectifier 2.7v500F Screw Hole Large Capacity Capacitor
$90.34Electronic Accessories & SuppliesAdd to cartDescriptionThis product can be used in electronic devices such as:RAM, smart three-meter, motor drive, clock circuit, toys, CMOS power failure protection, digital camera, hand-cranked rechargeable flashlight, PDA and other fields as a backup power supply.SpecificationBrand:GDCPHModel:16V83FCapacity:83FRated voltage:16 VSize:231*35*65mmPitch:7mmPackage included1 x capacitor
5pcs PWM DC Motor Governor 5V-16V 10A Speed Switch LED Dimmer Speed Controller
$22.64Motor PWM Speed ControllerAdd to cartParameterMaximum voltage:16VMinimum voltage:5VContinuous current:10AShort circuit maximum current:20A (less than 10 seconds)Speed control mode:PWM stepless speed regulation, can also be used to adjust the lightControl mode:speed control potentiometer (clockwise open, continue to rotate clockwise from 1% to 99%)Duty cycle:0%-99% (0% position is the leftmost state of the potentiometer).When the current is on, 0.002A (there is no …
5pcs PWM DC Motor Governor 5V-16V 10A Speed Switch LED Dimmer Speed ControllerRead More
3pcs 7W 9W 12W 15W LED Non Isolated Modulation Light External Driver Power Supply AC90-265V Constant Current Thyristor Dimming Module
$17.33Driver ModuleAdd to cartSpecificationsInput voltage:AC90-265VOutput voltage:DC21-48VOutput current:300mA(adjustable)Product size:68*34*22mmWorking temperature:Ta:50 TC:75Efficiency:≥80%Power factor:0.6Product application:spotlight PAR light / bulb light / candle light / etc.Package Included3 x 7W 9W 12W 15W LED Non Isolated Modulation Light External Driver
5Set Mini Emergency Hand-cranked Dynamotor Charger Portable Hand-cranked Generator 3V 5V for Diy Electronic Production with Clip Lines
$37.08Electronic Accessories & SuppliesAdd to cartDescriptionUnderstand the gear’s speed-increasing transmission conversion and the principle of electric energy generation, and cultivate the manual and brain skills, which is very suitable for manual classes in schools or for adults and children to play together!When shaking slowly for one second or more, the generating voltage can easily reach 3V, and it is easy …
APPJ Single End 6J1 + FU32 Tube Amplifier Board Class A Power AMP Hifi Vintage Audio Assembled Board
$182.24Amplifier BoardAdd to cartNew update:The appearance is updated from March 6, 2021.SpecificationsAssembled, solder freeDriver tubes:6J1x2PCSPower tubes:FU32x2PCSPower output:3W+3W @8ohmFrequency response:30-40KHz(+-1dB)Input sensitivity:550mVSignal-to noise-ratio:-80dB/3WInput power:85-264VACPower consumption:40WInput impedance:10K ohmOutput impedance:16ohm,8ohm,6ohm,4ohmPackage dimension:12*21*17cmPackage weigth:1.5KGNoteThe self-made shell must be opened with sufficient heat dissipation holes, preferably 50% of the shell area, at least 30%, otherwise it will affect the service life.Package Included1 x End 6J1 …
Caturda C2707 4Channel I2C interface Current Voltage Power Monitoring Module for Raspberry Pi
$39.03Raspberry Pi & Orange PiAdd to cartSpecificationsCurrent and power monitor for Raspberry Pi, 4 channels, can monitor the current, voltage, power and voltage across the sampling resistor through the I2C/SMBus interfaceFeaturesRaspberry Pi 40pin GPIO Interface, fit for Raspberry Pi all SeriesSupport 4 Channel I2C/SMBus CommunicationOnboard 1ohm 1% Resistance.Monitor 3.2A Bidirectional current12bit ADC Measuring 0-26V VoltageWorking Voltage:3.3V/5VInterface:I2C/SMBusResistance:1ohm 1%Voltage Range:0-26VCurrent:÷3.2ASize:65mmx30mmPackage Included1* Monitoring Module
Reviews
There are no reviews yet.