10pcs Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology Small Production Kit
$29.32
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
The purpose of the experiment
1. Understand and recognize the light-emitting diodes and illuminate the light-emitting diodes (LEDs);
2. Understand the role of understanding resistance, series and parallel resistance;
3. Understand the self-locking switch;
4. Understand and recognize adjustable resistors and use adjustable resistors;
Experimental steps
Step 1:The long leg of the light-emitting diode (LED) is the positive pole, and the short leg is the negative pole. First, the long wire of the LED is connected to the black wire (negative electrode) of the battery case, and the short leg of the LED is connected to the red wire (positive electrode) of the battery case. At this time, the light emitting diode (LED) is not lit. Then send it over again, let the long leg of the LED connect to the red line of the battery box, and the short leg of the LED is connected to the black line of the battery box. At this time, the LED lights up, indicating that the LED is in one-way operation and the single-pass characteristic of the diode .
Step 2:In the circuit of the experimental step 1, a resistor of 220 ohms is inserted in series, and the brightness of the LED lamp is lowered, and the resistance hinders the current.
Step 3:Connect a 220 ohm resistor in parallel with the resistance in the circuit of the experimental board 2. The brightness of the LED is increased, indicating that the total resistance of the resistor in the circuit is reduced after the resistors are connected in parallel.
Step 4:Change the two resistors of the experimental step 3 from parallel to series. After the series connection, the brightness of the LED lamp is the lowest. After the series connection of the resistors, the total resistance of the resistor in the circuit increases.
Step 5:Replace the original resistor with a potentiometer. The potentiometer has 3 feet, and the resistance of pins 1 and 3 is fixed. The resistance of pins 1 and 2, 2 feet and 3 feet can be changed by adjusting the potentiometer knob. When experimenting, you can pick up 2 of them. The foot has to experiment many times, adjust the potentiometer knob to observe the change of LED brightness, so that you can fully understand the potentiometer.
Step 6:Know the self-locking. Press and wait for the light to be on, then press the light to turn off.
Package included
10 x DIY LED Dimming Lights Technology Small Production Kit
Weight | 0.27 kg |
---|
Customers Also Viewed
Excellway 11Pcs Terminal Removal Tool Kit Wiring Connector Pin Release Extractor
$14.16ConnectorsAdd to cart11pcs Terminal Removal Tool Kit Wiring connector Pin Release Extractor PullerBrand:Excellway®Color:BlackMaterial:AluminumFeature1.This kit set is designed to remove car wire terminals without damage.2.Please don’t Pry the terminals with this kit, Just push and pull the terminal pins.Packing Included1x 11pcs/set Wire Terminal Removal Tool
20pcs 0.36 inch DC0V-32V Blue LED Digital Display Voltage Meter Voltmeter Reverse Connection Protection
$67.74Test & Measuring ModuleAdd to cartFeature∵ Super high precision∵ Ultra-low startup voltage, red minimum 2.5V, green minimum 2.7V, blue minimum 3.0V. When the power supply voltage is lower than 3.5V, only the brightness is lowered, but the measurement accuracy is not affected.∵ With reverse connection protection, it will not burn.Measuring range:0.00V-32.0VPower supply range:Red DC2.50-32.0V, green DC2.70-32.0V, blue DC3.00-30.0VHighest input:DC32.0V. Note:If …
10Pcs 100mm OD 12mm 3mm Thick Wall Borosilicate Glass Blowing Tube
$30.36Lab TubesAdd to cartProduct DescriptionHigh quality borosilicate glass, Premium borosilicate tubing, preferred by scientific and artistic glassblowers world-wide. HEAVY wall tubing 10 pieces, 12mm outside diameter with a 3mm wall – all approximately 100mm long. This glass tube bends easily with propane (LPG) and oxygen mix. Brand new, high quality, heat and corrosion resistant. SpecificationName:10Pcs 100mm OD 12mm …
10Pcs 100mm OD 12mm 3mm Thick Wall Borosilicate Glass Blowing TubeRead More
VHM-306 TPA3118 2x30W 12-26V DC Stereo Audio bluetooth 4.2 Digital Power Amplifier Board for Amplifiers D3-001
$16.83Amplifier BoardAdd to cartSpecificationsModel:VHM-306 Audio input:DC12~36V Power amplifier chip:TPA3118 Bluetooth channel:stereo Output Power:30W*2Applicable impedance:4,6,8Ω AUX input:3.5 earphone holder Product Size:70*52*12mm Package Included1 x VHM-306 TPA3118 2x30W Bluetooth 4.2 Digital Amplifier Board
10pcs XD-M131 DC 12V Photosensitive Resistor Module Light Control Switch Photosensitive Relay Module
$49.09Relay ModuleAdd to cartSpecificationProduct model:XD-M131Product Name:photosensitive relay moduleOperating voltage:12VOutput mode:one channel relayOverall size:52 x 31 x 31mmDescription1. This product is mainly used for light detection, brightness detection and control and other occasions, through the potentiometer can be adjusted to detect brightness threshold. With the relay, it can do a variety of brightness detection switch, you can control a …
5pcs 1.8 inch LCD TFT Display Module with PCB Backplane 128X160 SPI Serial Port
$54.01Display ScreenAdd to cartFeatureResolution:128X160Driver IC:ILI9163/ST7735Module with regulator IC supports 3.2V/5V power supplyWith SD card holder, you can do experiments like digital photo frameThe module reserves the Nokia3310/5110 interface, supports the 1602 interface, and directly plugs in and out.IO for streamlined wiring:(only 3 IOs after optimization)1. RST– directly connected to the microcontroller reset signal terminal, this IO can save2. …
5pcs 1.8 inch LCD TFT Display Module with PCB Backplane 128X160 SPI Serial PortRead More
Reviews
There are no reviews yet.