BESTEP 2 Channel 5V Relay Module High And Low Level Trigger for Auduino
$6.55
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
The module uses genuine quality relay, normal open interface maximum load:AC 250V/10A, DC 30V/10A.
The chip optocoupler isolation, strong driving ability, stable performance, trigger current 5mA.
Working voltage is 5V.
Each channel of the module can be set up by high jumper or low level trigger.
Fault tolerant design, even if the control line is broken, the relay will not act.
Power indicator (green), 2 relay status indicator (red).
The interface design is humanized, all interfaces can be directly connected through the terminals, so it is very convenient.
Module size:50mm x 42mm x 18.5mm (length x width x height).
There are 4 fixed bolt holes, holes 3.1mm, spacing 67mm x 44.5mm.
Module interface
1, DC+:Connect the power positive pole (voltage according to relay 5V).
2, DC-:Connect the power negative pole.
3, IN1-IN2:According to the setting of each way, the corresponding relay-operating can be controlled by high or low level.
Relay output:there is a 6 wire interface, all interfaces can be directly connected to lead to facilitate user use.
1, NO1–NO2:Relay normal open, the relay suspends before pulling in, and then short-connect with the COM.
2, COM1–COM2:Relay common interface
3, NC1–NC2:Relay normal close, short connected with COM before pulling inand suspended after pulling in.
High and low level trigger option
1. S1-S2 is the high level trigger selection of relay 1 Channel -2 Channel.
2. When COM is short connected with LOW, the corresponding relay is LOW level trigger, while when COM is short connected with high end is high level trigger.
Package Included
1 x 2 Channel 5V Relay Module
Weight | 0.033 kg |
---|
Customers Also Viewed
Geekwrom HD 3.5 inch TFT Display Shield 800×480 for Raspberry Pi 3B 2B + Acrylic Matching Case Kit
$121.30Raspberry Pi & Orange PiAdd to cartGeekwrom HD 3.5 Inch TFT Display Shield 800×480 For Raspberry Pi 3B 2B + Acrylic Matching Case KitHD 3.5 Inch TFT Display Shield 800×480 For Raspberry Pi 3B 2BFeatures– Demensions:85mm*56.5mm;– Resolution:800 x 480, 3.5 inch;– 267ppi High PPI display screen;– 11ms High Response Time(more than 60 fps);– 160° Wide Viewing Angle;– 900:1 High Contrast Ratio;– …
intelligent Screen Solar Pure Sine Wave Power inverter 1200W-6000W DC To AC 110V 120V Converter
$121.49InvertersAdd to cartWatt 1200W Voltage 12V Type Single digital display / Watt 2200W Voltage 12V Type Single digital display / Watt 3000W Voltage 12V Type Single digital display / Watt 3000W Voltage 24V Type Single digital display / Watt 3000W Voltage 48V Type Single digital displ
500W Aquarium Submersible Stainless Steel Heating Rod Adjustable Heater
$48.59Solar CollectorsAdd to cartDescriptionMaterial:Stainless SteelColor:SilverPlug:US PlugVoltage:220-240V 50HzWattage:500WTemperature range:16-32°CCable Length:120cm/47.24inch(appr.)Heating Rod Length:41cm/16.14inch(appr.)FeaturesMade of stainless steel material, anti-rust, useful and durable.Double insulation & waterproof.Keep the water temperature steady.Suitable for aquarium:500L (for reference only).Simple adjustment and easy to read temperature indicator.Easy to install with 2 strong suckers (mounting distance of 2 suckers is about 9.5cm).Adjustment knob allows you to adjust the …
500W Aquarium Submersible Stainless Steel Heating Rod Adjustable HeaterRead More
5pcs JoyStick Module Shield 2.54mm 5 pin Biaxial Buttons Rocker for PS2 Joystick Game Controller Sensor
$14.30Other Module BoardAdd to cartFeaturejoystick joysticks standard interface module electronic building blocks and 2.54mm pin interface leads.Phillips is a two-way rocker 10K resistor, with the joystick in a different direction, tap the resistance vary. This module uses a 5V supply, the original state X, Y readout voltage of 2.5V or so, when pressed with the direction of the arrow, …
4Pcs Geekcreit Ultrasonic Module HC-SR04 Distance Measuring Ranging Transducers Sensor DC 5V 2-450cm
$9.83Sensor & Detector ModuleAdd to cartDescriptionWorking Voltage:5V(DC)Static Current:Less than 2mA.Output Signal:Electric frequency signal, high level 5V, low level 0V.Sensor Angle:Not more than 15 degrees.Detection Distance:2cm-450cm.High Precision:Up to 0.3cmInput Trigger Signal:10us TTL impulseSignal:output TTL PWL signalMode of connectionVCCtrig(T)ech0(R)GNDUse MethodSupply module with 5V, the output will be 5V while obstacle in range, or 0V if not.The out pin of this module is …
1MHz-700MHZ 3.2W HF VHF UHF FM Transmitter RF Power Amplifier for Ham Radio
$50.29RF amplifierAdd to cartApplicationBroadband RF power amplifier for all types of wireless applications, FM shortwave radios remote control toys, digital radio, etc., enter 1 milliwatt (0DBM) maximum output of 3 watts, 15V voltage supply, broadband work 1MHZ to 700MHZ can be work. As a result of well-designed, low end that can reach 35DBM (3W), at 500M, the output …
1MHz-700MHZ 3.2W HF VHF UHF FM Transmitter RF Power Amplifier for Ham RadioRead More
Reviews
There are no reviews yet.