Micro ATmega32U4 5V 16MHz Development Board
$26.23
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
The Micro ATmega32U4-MU is a tiny microcontroller board based on the ATmega32U4. It has 20 digital input/output pins (7 of which can be used as PWM outputs and 12 as analog inputs), a crystal oscillator, a micro-USB connection, an ICSP header and a reset button. With a 16 MHz frequency and 5V operating voltage, this board is similar to the Arduino Leonardo, although the Micro ATmega32U4-MU is more compact (17.78*48.26mm).
The board contains everything needed to support the microcontroller; you just have to connect it to a computer and get started! Its form factor enables it to be easily placed on the circuit board.
Like the Arduino Leonardo, the Micro ATmega32U4-MU has built-in USB connection, eliminating the need for a converter. This allows the Micro to appear to a connected computer as an HID-device, such as a keyboard or mouse, in addition to a COM-port. The board is also able to perform other Arduino Leonardo functions.
Power
The Micro ATmega32U4-MU can be powered via a USB connection.
Power Supply
5V:The regulated power supply used to power the microcontroller and other components on the board. This can come either from VIN via a voltage regulator, or be supplied via USB, or another regulated 5V supply.
3V3:A 3.3V supply generated by the on-board regulator. Maximum current draw is 50mA.
GND:Ground pins.
I/O Pins
Each of the 20 digital pins can be used as an input or output. They operate at 5V. Each pin can provide or receive a maximum of 40 mA, and has an internal pull-up resistor (disconnected by default) of 20-50 k Ohms. In addition, some pins have additional functions
— Serial interface:0(RX) and 1(TX) pins. Used to receive (RX) and transmit (TX) data using the ATmega32U4 hardware serial capability. Note that on the Micro ATmega32U4-MU, the Serial class refers to USB (CDC)-communication, for data transfer on pins 0 and 1, use the Serial1 class.
— TWI:2 (SDA) and 3 (SCL) pins. Support TWI (12C) communication using the Wire library.
— External interrupts:3 (interrupt 0), 2 (interrupt 1), 0 (interrupt 2), 1 (interrupt 3) and 7 (interrupt 4). These pins can be configured to trigger an interrupt on a low value, a rising or falling edge, or a change in value. See the attachInterrupt() function for details.
— PWM:3, 5, 6, 9, 10, 11 and 13. Provide 8 bit PWM output with the analogWrite() function.
— SPI:on the ICSP header. These pins support SPI communication using the SPI library. Note that the SPI pins are not connected to any of the I/O pins as they are on the Arduino Uno. They are only available on the ICSP connector.
— Analog inputs:A0 — A5, A6 — A11 (on digital pins 4, 6, 8, 9, 10 and 12). The Micro ATmega32U4-MU has 12 analog inputs (A0 — A11), all of which can also be used as digital i/o. Analog inputs A0 — A5 appear in the same locations as on the Arduino Uno; inputs A6 — A11 are on digital i/o pins 4, 6, 8, 9, 10 and 12, respectively. Each analog input provide 10 bits of resolution (1024 different values). By default, the analog inputs measure from 0 to 5 volts, though it is possible to change the upper end of their range using the AREF pin and the analog Reference() function.
— Reset. A low signal level resets the microcontroller.
LEDs
* RX and TX — flash when data is being transmitted via USB connection.
* ON — power indicator.
* L — LED connection to digital pin 13.
Memory
The ATmega 32U4 microcontroller has 32 KB memory (with 4 KB used by the bootloader). It also has 2.5 KB SRAM and 1 KB EEPROM (which can be read and written with the EEPROM library).
The Micro ATmega32U4-MU has a number of facilities for communicating with a computer, another Arduino device or microcontrollers.
The ATmega32U4 provides serial UART TTL serial communication, which is available on digital pins 0(RX) and 1(TX).
Having hardware support for USB, the ATmega32U4 also allows for serial communication with the computer over a virtual COM port.
The Micro ATmega32U4-MU also acts as a USB 2.0 device, using standard USB COM drivers. The Arduino software includes a serial monitor that allows simple textual data to be sent to and from the board. Which we will do in the example given under the description.
A SoftwareSerial library allows for serial communication on any of the ATmega32U4-MU’s digital pins.
The ATmega32U4 also supports I2C (TWI) and SPI communication. The Arduino software includes a Wire library to simplify use of the 12C bus. The SPI library can be used for SPI communication.
Programming
The board can be programmed with Arduino software, by selecting ATmega32U4 in the Board menu.
The ATmega32U4 microcontroller on the Micro ATmega32U4-MU comes preburned with a bootloader that allows you to upload new code to it without the use of an external hardware programmer.
You can also bypass the bootloader and program the microcontroller through the ICSP (In-Circuit Serial Programming) header.
Automatic Reset
Rather than requiring a physical press of the reset button before an upload, the Micro ATmega32U4-MU is designed in a way that allows it to be reset by Arduino software running on a connected computer. The reset is triggered when the virtual CDC COM port is opened at 1200 baud and then closed. When this happens, the processor will reset, breaking the USB connection to the computer. After the processor resets, the bootloader starts, remaining active for about 8 seconds. The bootloader can also be initiated by pressing the Reset button. Note that when the board first powers up, it will jump straight to the user sketch, if present, rather than initiating the bootloader.
USB Overcurrent Protection
The Micro ATmega32U4-MU has a resettable polyfuse that protects the computer’s USB ports from shorts and overcurrent. Although most computers have their own internal protection, the fuse provides an extra layer of protection. If more than 500mA is applied to the USB port, the fuse will automatically break the connection until the short or overload is removed.
Microcontroller:ATmega32U4-MU
Power Out:3.3V-180m
5V-800m
Power IN. USB:5V
Power IN. VIN/DC Jack:5V
Power Consumption:5V 220mA
Logic Level:5V
USB:Micro USB
Clock Frequency:16MHz
Operating Supply Voltage:3.3V
Digital I/O:20(7-PWM)
Analog I/O:12
Data RAM Type/Size:2.5Kb
Data ROM Type/Size:1Kb
Interface Type:ISP
Operating temperature:−40㎡°/+85㎡°
PCB size (L*W):48.26*17.78mm
Weight:8.5g
Documents
Dimensional drawing:Click here to open
Pinout:Click here to open
Schematic:Click here to open
Package includes
1 x Micro ATmega32U4 5V 16MHz Development Board
Weight | 0.015 kg |
---|
Customers Also Viewed
REX-C100 Digital RKC PID thermostat Temperature Controller 0 To 400 Degree K Type Relay Output
$24.04Electronic Accessories & SuppliesAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.FeaturesThis is a double universal programmable digital display temperature controller that supports many types of thermocouple sensor.It is powered by 220V ACSpecificationsScreen:Double screen for Celsius (C)Range:0-400C (Only when with K-type thermocouple factory)Thermocouple:K, …
High Gain 10dB 2.4G Wifi Directional Image Transmission Yagi Antenna
$20.07RF amplifierAdd to cartSpecificationWorking frequency:2.35-2.55GHZAntenna gain:10.5dB (typical value)Antenna standing wave ratioPower capacity:10WMechanical size:5x10Cm (excluding joints)Radiation direction:directional linear polarizationConnector type:SMA-K (standard female, outer screw and inner hole, can be customized)Package included1 x Antenna
20pcs DD2712SA 3.5A Mini 5V-27V to 12V DC DC Step Down Buck Power Converter Module Voltage Regulator
$83.70Boost & Buck ModuleAdd to cartDescriptionInput voltage:5-27VOutput voltage:5V Maximum output current:2.5AShort time maximum output current:3.5A Quiescent current:about 250uAWorking frequency:900KHz.Working efficiency:77-92% Size:25 x 15 x 6.3 mmOvertemperature shutdown, Under-Voltage Lockout (UVLO), BS-voltage protection, and short circuit protection.Note1. Input voltage can not be greater than the maximum input range.2. Output power can not be greater than the maximum load for a long …
Quick Charge 3.0 DIY Power Bank 18650 Battery Case QC3.0 5V 9V 12V DIY Kit Power Bank 2A 18650 Battery Fast Charger Shell
$25.14Module ComponentsAdd to cartNote1. Please Use flat-headed 18650 DIY2. If use the old battery,pls test the voltage,more than 3.5v and the Internal resistance less than 60 .3. It can’t use the flashlight 18650 battery4. Do not connect the positive and negative terminals backwards, otherwise it will burn the circuit board5. Don’t close the cover until the test is …
25x25x5cm Soundproofing Triangle Sound-Absorbing Noise Foam Tiles
$14.16FoamAdd to cartDescription25x25x5cm Soundproofing Triangle Sound-Absorbing Noise Foam TilesSpecificationsMaterial:Polyurethane foamDimensions:25 * 25 * 5 cm / 9.84 * 9.84 * 1.97 inchBlack:ColourQuantity:1pcFeatures– Bounce rate deformation, a long duration.– Waterproof, anti-moisture, good air permeability.– Wherever to help block sound and prevent echoes in the room.– These panels provide a strong noise reduction, good for studios, recording studios, vocal …
25x25x5cm Soundproofing Triangle Sound-Absorbing Noise Foam TilesRead More
Reviews
There are no reviews yet.