30cmx1M PCB Dry Film Photosensitive Photoresist Sheets for Circuit Production
$6.55
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
PCB photosensitive dry film for circuit production
Any light containing ultraviolet can be exposure, and the wavelength of light is 370nm.
Size:30 x 100 cm / 11.81inch x 39.37inch
Color:As pictures shown
Features
– Photographic film, also known as dry film, is used to make PCB board, stick it on top of the PCB, it will become a sensitive circuit board.
– Suitable for plating, hole covering, and the etching process.
– Excellent ability to cover holes
– High Resolution
– Excellent adhesion to almost all surfaces
– Image clarity after exposure
– Front-panel is very clean after developed
How to use it
1. Clean your board. Cut dry film a little larger than your board.
2. Apply Resist:This Photoresist has 3 layers, the top and bottom layers are clear protective layer, so at the first, you need remove one protective layer, the easy way is to use two small pieces of tape. Then apply the middle layer on board.
3. Expose:Place your negative artwork over the rest protective layer.
4. Develop:Remember:you need NEGATIVE film developer, Remove the rest protective layer on the film. After 3 minutes take board out of developer and hold under running water to check,you can always place it back in the developer if needs more time.
Etching
The dry film is resistant to most of the acid etching solution, the PH value can be resistant to most alkaline etching solution between PH8.0 ~8.5.
Cover hole
1.5 mil dry film can fully cover a 0.25 inches thickness hole.
Plating
The dry film is available in most common use of the plating bath, no wrinkles, no color.
Package included
1 roll photosensitive dry film
Weight | 0.062 kg |
---|
Customers Also Viewed
5Pcs A87 4 Channel Optocoupler Isolation Module High And Low Level Expansion Board
$17.08Other Module BoardAdd to cartDescription 1. Function:Use the low level to control the high level. Such as the use of single-chip 3V or 5V voltage control 9V or 12v voltage. 2. HVCC should not exceed 24V. Output OUT1 / OUT2 / OUT3 / OUT4 output current equal to HVCC / 5.1K, absorption current 500ma. 3. This module uses TLP281 …
5Pcs A87 4 Channel Optocoupler Isolation Module High And Low Level Expansion BoardRead More
3pcs DC 3.3V To 20V 5.8GHz Microwave Radar Sensor intelligent Trigger Sensor Switch Module
$16.24Sensor & Detector ModuleAdd to cartDescriptionIt uses Doppler radar technology, with auto-sensing capabilities to control other product,High sensitivity, sensor distance, reliability, wide angle sensor,Wide supply voltage range and other characteristics. Widely used in lighting situations,anti-theft alarm situations.Features1. microwave sensors using planar antenna and receiving echo.2. The switch is active sensors.3. The sensors emit a high-frequency electromagnetic waves and receives their …
3pcs DC 3.3V To 20V 5.8GHz Microwave Radar Sensor intelligent Trigger Sensor Switch ModuleRead More
24V Air Parking Heater Flame Sensor Igniters Flame Detecter 82306B for Webasto Air top 2000
$70.86Solar CollectorsAdd to cartSpecificationsBrand Name:AutoleaderMaterial:Silicon NitrideOEM:82306BItem weight:11gFeaturesThis product is mainly made of silicon nitride ceramic substrate, with tungsten filament as the heat source, tungsten wire embedded in silicon nitride matrix, via hot-press sintering process to form an organic whole, then through grinding, welding wire, thus made the ignition components.Fitmentfor Webasto Air Top 2000Package Included1x Parking Heater Senser
L293D WiFi Smart Robot Car Motor Driver Expansion Board Dual High Power H Bridge Based on ESP12E
$9.79Expansion Board & ShieldAdd to cartL293D WiFi Smart Robot Car Motor Driver Expansion Board Dual High Power H Bridge Based On ESP12E For Specifications 1. Motor power (VM):4.5 ~ 36V 2. Control power (VIN):4.5V ~ 9V(10V MAX) 3. Provide the shortcut connector (short by VM and VIM), thus can use 4. May use common power source (4.5V~9V) by shorting VM …
220V 1000W Hot Plate Electric Iron Burner Heating Stove Heater Household Laboratory Heating Equipments
$52.64Laboratory Heating EquipmentsAdd to cartSpecificationsType:Electric Stove BurnerPlug Type:EUColor:WhiteVoltage:220VPower:1000WRegulating temperature:5 LevelsMaterial:Stainless Steel + IronSize:14*14*5CM (5.5*5.5*2in)Features– Adopted iron shell, thicken panel, material sturdy and durable to use– Portable single burner with 500 watts of power– Powered by electric, do not need fuel, eco-friendly– Easy-to-use temperature-setting knob for low, medium, or high heat– Provides quick and sustained heat; power indicator light– Single …
Reviews
There are no reviews yet.