DC 12V-36V 500W PWM Brushless Motor Controller with Hall Motor Voltage Speed Regulation Balanced Car Driver Control Board Module
$26.23
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
Operating voltage:DC 12V-36V
Operating Current
Driver Power
Speed Voltage:0.1V-5V
Operating Temperature:-40-85C
Humidity:90%RH
Stall protection:Yes
Enable Control:Yes
Over-current protection:Yes
Steering control:Yes
Speed control signal:Yes
Size:63*42*17mm(L*W*H); Probe size 3mm,length:fixing hole center distance 57mm; width:fixed hole center distance 36.5mm
Power terminal Out
VCC(positive power supply)
GND(negative one)
MC(motor phases W)
MB(motor phases V)
MA(motor phase U)
Set for the control side
GND control terminal ground
VR the governor end 0-5V(corresponding to 10% of motor speed -100%)
ZF reversing control(connected to 5V or ground can charge the motor rotation direction)
M tachometer pulse output(depending on the number of motor poles corresponding to the number of pulse per revolution of the output number)
EL enable control terminal(connected to 5V ot ground running then 5V, grounding the motor stops)
5V 5V control terminal
HALL for the hall terminals
5V, Hall power positive
Ha, Hall signal
Hb, Hall signal
Hc, Hall Signal
GND, Hall negative
Wiring
Control terminal for SET
1. The motor speed control wiring methods:available potentiometer system speed can also be connected to the MCU control, when the potentiometer control wiring, the potentiometer middle pin is connected to VR speed port, potentiometer connected to both ends of 5V and GND terminal voltage more high speed faster
2. Motor steering control wiring methods:you can switch control can also be connected to the MCU control, to GND in one direction, then in one direction 5V
3. Pulse speed signal:high and low output . IC can not understand the information with the customer request
Hall signal inputs for hall
Wiring diagram is shown, one corresponding to the HA, HB,HC and on the motor, 5V power supply connected to the motor hal signals positive, GND power supply negative signal to the motor hall
Note:Due to different motor manufacturers to make the hall of hall line order does not necessarily follow the line on the board to match the array, need to be adjusted, please pay attention! If the line array wrong, does not boot properly, current, or start other phenomena not open, forced to use the drive plate will burn!!!
Motor driver board 12-36V DC power input ,VCC positive power supply,GND power supply is negative
Electrical wiring methods:Brushless DC motor for the three lines, corresponding MA/U,MB/V,MC/W
Tips:If you use less than 60W, without additional heat sink , be sure to add more than 60W heatsink fins drive efficiency without lowering the temperature is too high will shine into permanent damage! The size of the heat sink may be a bad environment based work(recommended cooling surface area greater than 200 square centimeters)!When installing the heat sink ,must pay attention to the back of the module 6 MOS pipe insulation, no insulation, it will be adhered to drive plate permanently damaged! Proposes to add insulation films, both sides of the insulating sheet plus thermal grease!
Package includes
1 x Controller
Weight | 0.029 kg |
---|
Customers Also Viewed
50Pcs 12V Female DC Power Socket Jack Plug Wire Connector Cable CCTV DC 5.5 x 2.1mm
$32.76Module ComponentsAdd to cartFeaturesDC 5.5 x 2.1mm.Wire Specification:0.15mm²Length:Approx. 27cmMax Current Rating:2AMax Power Rating:60WTransmission voltage:1V~38VUsage temperature:-50→~65→Material:Copper WireUse for:Led Driver/ Strip connector/ CCTV Camera.Package Included50 x 12V DC Connector Cables
EMC EMI Low Noise Pre-RF Amplifier 20dB 5MHz-5GHz RFamp002
$87.30RF amplifierAdd to cartParameter1. Power supply voltage:11V-15V DC2. Gain:greater than 20DB in the 30MHz-1GHz frequency band3. Input and output impedance:50┯4. Maximum output power:10dBm5. Input signal:-10DBm6. Bandwidth:30MHz to 3GHz (gain is different under different frequencies)Measured gain (prototype)F=5.0MHZ GAIN=13.15DBF=10.0MHZ GAIN=23.89DBF=30.0MHZ GAIN=27.06DBF=50.0MHZ GAIN=27.92DBF=500.0MHZ GAIN=24.84DBF=1.0GHZ GAIN=22.01DBF=1.5GHZ GAIN=20.72DBF=2.5GHZ GAIN=17.65DBF=3.5GHZ GAIN=10.06DBF=4.0GHZ GAIN=9.09DBF=5.0GHZ GAIN=8.90DB7. Noise figure NF (theoretical value)500MHz@ 0.6dB1GHz@ 0.7dB2GHz@ 0.7dB3GHz@ 1.1dB4GHz@ 1.6dB5GHz@ 2.1dBComparison …
EMC EMI Low Noise Pre-RF Amplifier 20dB 5MHz-5GHz RFamp002Read More
RX24 100W 30R 30RJ Metal Aluminum Case High Power Resistor Golden Metal Shell Case Heatsink Resistance Resistor
$6.55Electronic Accessories & SuppliesAdd to cartFeaturesIt has the characteristics of small size, high power and high precision.It is sealed by professional technology.It has the advantages of stronger heat resistance, higher temperature resistance, moisture resistance, high anti-vibration and explosion protection.Scope of application:Testing power supply, frequency converter, automobile LED lamp, automation equipment, audio, frequency divider, servo industry and other harsh industrial control …
5pcs SRX882 433/315MHz Superheterodyne Receiver Module Board for ASK Transmitter Module
$16.71Smart ModuleAdd to cartItem OverviewThe SRX882 is a super-heterodyne receiver module with a micropower and strong driving force in conjunction with the ASK transmitter module. It has high stability, anti-interference and high cost performance, and also has a strong driving force, which can pass ROHS, FCC, CE and other certifications. The data port can be directly connected to …
5pcs SRX882 433/315MHz Superheterodyne Receiver Module Board for ASK Transmitter ModuleRead More
13.5mm Adjustable Laser Pointer Module Holder Mount Clamp 3 Axis
$42.51Engraving Parts & AccessoriesAdd to cartDescriptionMaterial:stainless steelColor:blackMount Inner Diameter:13.5mmSize:40X60mm/1.57X2.36inch(L*H)Feature1. Stainless steel laser moudle holder2. Professional angle and height adjustable design3. Installed on the laser module,it can become a professional laser pointer or laser locator4. Can also used a as a heatsink for the laser module,extend the laser module life time5. Fit for 12mm diameter laser modulePackage included1X Laser Module Holder
Mask Scary Glow Mask LED Mask for Halloween Mask Party Masks Neon Maske Skeleto Halloween Party Decor
$17.17EL ProductsAdd to cartColor. Red / Color. Orange / Color. Yellow / Color. Blue / Color. Blue / Color. Purple / Color. White / Color. Pink / Color. Fluorescent Green / Color. Green / Color. Transparent Blue /
Reviews
There are no reviews yet.