SI24R1 NF-01-S 2.4G Wireless Serial Module Transparent Transmission
$6.55
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
NF-01-S is a 100mW power 2.4G wireless module, high-altitude rate (up to 2Mbps), using SPI interface, send and receive in one pure hardware module; high stability, cost performance, Volume, use of all-industry components.
Has been mass production and reached millions of shipments, and applies to a variety of application scenarios.
NF-01-S can be widely used in a variety of networking occasions, suitable for wireless mouse and keyboard, wireless remote control, somatosensory equipment, active RFID, NFC, low power consumption network of wireless sensor networks, is the ideal solution of Internet of Things application.
NF-01-S adopt DIP-8 package, whether learning or mass production, can quickly docked to existing products, no need soldering, direct plug, easy to use.
Information link:http://wiki.ai-thinker.com/2.4g
Features
• DIP-8 ultra-small package, built-in 2.4G antenna, small size, easy to use
• Supports data reception for six channels
• Supports common modulation such as GFSK / FSK
• Supports 2Mbps / 1Mbps / 250Kbps data rate
•Multi-frequency:126 frequency, to meet the needs of multi-point communication and frequency hopping communication
• Internal integration of high PSRR LDOs
• Wide supply voltage range:1.9 ~ 3.6V
• Average emission current as low as 110mA
• Receiver sensitivity:-96dBm @ 250kbps
• Maximum transmit power:+ 7dBm
• Four-wire SPI interface for up to 10MHz
• Internal Integrated Smart ARQ Baseband Protocol Engine
• Transmit data hardware interrupt output
• Supports 1bit RSSI output
• Low application cost:The SI24R1 integrates all the high-speed signal processing parts associated with the RF protocol, such as automatic retransmission of lost packets and automatic generation of response signals. The SPI interface of the SI24R1 can be connected using the microcontroller’s SPI port or using the microcontroller I / O port to simulate, the internal FIFO can be with a variety of high and low speed microprocessor interface, easy to use low-cost single-chip.
• Easy to develop:Since the link layer is fully integrated on the module, it is very easy to develop. Automatic retransmission function, automatic detection and retransmission of lost packets, retransmission time and the number of retransmission software can automatically control the automatic response is not received a reply signal packet automatic response function, after receiving the valid data, the module automatically sends a response Signal, no additional programming Carrier detection – Fixed frequency detection Built-in hardware CRC error detection and point-to-multipoint communication Address control Packet transmission error Counter and carrier detection function can be used for frequency hopping settings can be set at six simultaneous receive channel address, can be selective Of the open receiving channel standard pin DIP 2.54mm pitch interface for easy embedded applications.
Parameter
Model:NF-01-S
Package:DIP-8
Size:28.6*15.3*3.2 mm
Communication Interface:SPI (The maximum rate of up to 10Mbps)
Air rate:250k~2Mbps, 3 Level adjustable(250kbps,1Mbps,2Mbps)
Spectral range:2400MHz~2525MHz adjustable, 1MHz Step forward
Antenna form:Onboard PCB antenna, gain 2dBi
Maximum transmit power:7dBm
Receiving sensitivity:-96dBm@250kbps
Average current:Emission current:25mA(7dBm)
Receive current:15mA (2Mbps)
Shutdown:current 1.0uA(Shutdown Mode)
Power supply range:1.9~3.6V, Typical value 3.3V
Operating temperature:-20 → ~ 85 →
Storage environment:-20 → ~ 90 → ,
Pin Explanation
NO.:Name:Direction:Use
1:VCC:-:Power supply, must be between 2.0 ~ 3.6V
2:GND:-:Ground, connected to the power supply reference ground
3:CSN:Input:The module chip select pin, is used to start an SPI communication
4:CE:Input:Module control pin
5:MOSI:Input:Module SPI data input pin
6:SCK:Input:Module SPI bus clock
7:IRQ:Output:Module interrupt signal output, low level active
8:MISO:Output:Module SPI data output pin
Package included
1 x SI24R1 NF-01-S 2.4G Wireless Serial Module
Weight | 0.001 kg |
---|
Customers Also Viewed
5Pcs CP2102 USB To TTL/Serial Module Downloader
$21.98Converter BoardAdd to cart5Pcs CJMCU CP2102 USB To TTL/Serial Module UART STC Downloader For Driver Installation Introduction:http://forum.hobbyant.com/forum-topic-56275.html Description CJMCU-CP2102 its highly integrated, built-in USB2.0 full-speed function controller, USB transceiver, crystal oscillator, EEPROM and asynchronous serial data bus (UART), supports full-featured modem signal without any external USB devices. CJMCU-CP2102 works with other USB-UART adapter circuit similar to the driver …
10pcs 180 Degree USB 3.0 Type A female Socket Connector SMT Charging Socket Plug Connector
$10.11Terminal BlocksAdd to cartSpecificationsColorBlueRated Current1.5ARated Voltage30VInsertion Force35N MaxDurability3000 Cycles Min Rubber CorePBT / Icp Ul94V-0 Resistance To Voltage500V Ac Min. Insulation Resistance≥1000MΩPull-Out Force10N Min.Initial 8-20N AfterWorking Temperature-20 Degrees To 60 Degrees Contact Impedance≤30mΩTerminalsBrass C2680,Nickel Base,Gold-Plated 1 u,Package included-10pcs X 180Degree Connectors
Dual Servos Knob Serial Port Control Board Futaba MG995 SG90 Steering Gear Debugging Module
$13.11Other Module BoardAdd to cartFeature1. The onboard stable 8-bit MCU is used to generate high-resolution PWM signals with precise control.2. Support manual mode and return to medium mode, switch by button, with mode indicator.3. Support knob adjustment or serial command control in manual mode.4. The serial port command control can use the matching host computer software or connect to …
Dual Servos Knob Serial Port Control Board Futaba MG995 SG90 Steering Gear Debugging ModuleRead More
Keyes Brick Laser Head Sensor Module (pad hole) with Pin Header Board Digital Signal
$4.36Sensor & Detector ModuleAdd to cartDescriptionThis sensor is fully compatible with ARDUI NO single-chip microcomputer, and its connection port is also compatible with Arduino sensor expansion board. It is mainly composed of a laser head, which is composed of a light-emitting tube core, a condenser lens, and a copper adjustable sleeve. After connecting to the power supply, we directly input …
Keyes Brick Laser Head Sensor Module (pad hole) with Pin Header Board Digital SignalRead More
5pcs DC3~5V AK-119 433.92MHZ 4 Pin Superheterodyne Receiver Board without Decoding -105dBm
$10.37Other Module BoardAdd to cartFeatures1. The product is small in size, high in sensitivity and strong in anti-interference ability;2. The same definition as the four-pin pin of RXB12, the usage is the same. The unit price is lower than RXB12 and can be directly replaced.Technical ParametersWorking voltage:DC3~5VTransmission rate:4.80KBPSQuiescent current:6mAReceive sensitivity:-105dBmDimensions:30 * 9 * 5mmWorking temperature:-20 ° C ~ +80 …
5pcs DC3~5V AK-119 433.92MHZ 4 Pin Superheterodyne Receiver Board without Decoding -105dBmRead More
150g Capacity Quartz Silica Melting Crucible Pot for Gold Silver Platinum Refine
$16.19Glassware KitAdd to cart150g Capacity Quartz Silica Melting Crucible Pot For Gold Silver Platinum RefineDescriptionMaterial:quartzCapacity:150gDiameter:43X57mm/1.69inch X2.24inch(ID*OD)Height:20mm/0.79inchDeepth:15mm/0.59inchNet Weight:40gFeatureQuartz silica melting crucibleProduced by modern ceramic processing technologyHigh orrosion resistance and strength,the temperature resistance up to 2800℃/5072FPerfect for gold silver casting and refine usagePackage included1X Quartz Silica Melting Crucible
WXD3-13-2W Precision Potentiometer 470R 470 Ohm Wirewound Multi-Turn Potentiometer
$4.50Module ComponentsAdd to cartSpecificationsResistance range:470┯Resistance tolerance:÷ 5%Rotation angle:3600 ÷ 20 Number of laps:10 lapsRated voltage:160VStarting torque:3.5 ~ 100mN.mRated power:2W (85 →) 0W (125 →)Linearity accuracy:÷ 0.3%Mechanical durability:10,000 weeksPackage included1 x Potentiometer
Reviews
There are no reviews yet.