SI24R1 NF-01-S 2.4G Wireless Serial Module Transparent Transmission
$6.55
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
NF-01-S is a 100mW power 2.4G wireless module, high-altitude rate (up to 2Mbps), using SPI interface, send and receive in one pure hardware module; high stability, cost performance, Volume, use of all-industry components.
Has been mass production and reached millions of shipments, and applies to a variety of application scenarios.
NF-01-S can be widely used in a variety of networking occasions, suitable for wireless mouse and keyboard, wireless remote control, somatosensory equipment, active RFID, NFC, low power consumption network of wireless sensor networks, is the ideal solution of Internet of Things application.
NF-01-S adopt DIP-8 package, whether learning or mass production, can quickly docked to existing products, no need soldering, direct plug, easy to use.
Information link:http://wiki.ai-thinker.com/2.4g
Features
• DIP-8 ultra-small package, built-in 2.4G antenna, small size, easy to use
• Supports data reception for six channels
• Supports common modulation such as GFSK / FSK
• Supports 2Mbps / 1Mbps / 250Kbps data rate
•Multi-frequency:126 frequency, to meet the needs of multi-point communication and frequency hopping communication
• Internal integration of high PSRR LDOs
• Wide supply voltage range:1.9 ~ 3.6V
• Average emission current as low as 110mA
• Receiver sensitivity:-96dBm @ 250kbps
• Maximum transmit power:+ 7dBm
• Four-wire SPI interface for up to 10MHz
• Internal Integrated Smart ARQ Baseband Protocol Engine
• Transmit data hardware interrupt output
• Supports 1bit RSSI output
• Low application cost:The SI24R1 integrates all the high-speed signal processing parts associated with the RF protocol, such as automatic retransmission of lost packets and automatic generation of response signals. The SPI interface of the SI24R1 can be connected using the microcontroller’s SPI port or using the microcontroller I / O port to simulate, the internal FIFO can be with a variety of high and low speed microprocessor interface, easy to use low-cost single-chip.
• Easy to develop:Since the link layer is fully integrated on the module, it is very easy to develop. Automatic retransmission function, automatic detection and retransmission of lost packets, retransmission time and the number of retransmission software can automatically control the automatic response is not received a reply signal packet automatic response function, after receiving the valid data, the module automatically sends a response Signal, no additional programming Carrier detection – Fixed frequency detection Built-in hardware CRC error detection and point-to-multipoint communication Address control Packet transmission error Counter and carrier detection function can be used for frequency hopping settings can be set at six simultaneous receive channel address, can be selective Of the open receiving channel standard pin DIP 2.54mm pitch interface for easy embedded applications.
Parameter
Model:NF-01-S
Package:DIP-8
Size:28.6*15.3*3.2 mm
Communication Interface:SPI (The maximum rate of up to 10Mbps)
Air rate:250k~2Mbps, 3 Level adjustable(250kbps,1Mbps,2Mbps)
Spectral range:2400MHz~2525MHz adjustable, 1MHz Step forward
Antenna form:Onboard PCB antenna, gain 2dBi
Maximum transmit power:7dBm
Receiving sensitivity:-96dBm@250kbps
Average current:Emission current:25mA(7dBm)
Receive current:15mA (2Mbps)
Shutdown:current 1.0uA(Shutdown Mode)
Power supply range:1.9~3.6V, Typical value 3.3V
Operating temperature:-20 → ~ 85 →
Storage environment:-20 → ~ 90 → ,
Pin Explanation
NO.:Name:Direction:Use
1:VCC:-:Power supply, must be between 2.0 ~ 3.6V
2:GND:-:Ground, connected to the power supply reference ground
3:CSN:Input:The module chip select pin, is used to start an SPI communication
4:CE:Input:Module control pin
5:MOSI:Input:Module SPI data input pin
6:SCK:Input:Module SPI bus clock
7:IRQ:Output:Module interrupt signal output, low level active
8:MISO:Output:Module SPI data output pin
Package included
1 x SI24R1 NF-01-S 2.4G Wireless Serial Module
Weight | 0.001 kg |
---|
Customers Also Viewed
5Pcs A87 4 Channel Optocoupler Isolation Module High And Low Level Expansion Board
$17.08Other Module BoardAdd to cartDescription 1. Function:Use the low level to control the high level. Such as the use of single-chip 3V or 5V voltage control 9V or 12v voltage. 2. HVCC should not exceed 24V. Output OUT1 / OUT2 / OUT3 / OUT4 output current equal to HVCC / 5.1K, absorption current 500ma. 3. This module uses TLP281 …
5Pcs A87 4 Channel Optocoupler Isolation Module High And Low Level Expansion BoardRead More
3pcs DC 3.3V To 20V 5.8GHz Microwave Radar Sensor intelligent Trigger Sensor Switch Module
$16.24Sensor & Detector ModuleAdd to cartDescriptionIt uses Doppler radar technology, with auto-sensing capabilities to control other product,High sensitivity, sensor distance, reliability, wide angle sensor,Wide supply voltage range and other characteristics. Widely used in lighting situations,anti-theft alarm situations.Features1. microwave sensors using planar antenna and receiving echo.2. The switch is active sensors.3. The sensors emit a high-frequency electromagnetic waves and receives their …
3pcs DC 3.3V To 20V 5.8GHz Microwave Radar Sensor intelligent Trigger Sensor Switch ModuleRead More
24V Air Parking Heater Flame Sensor Igniters Flame Detecter 82306B for Webasto Air top 2000
$70.86Solar CollectorsAdd to cartSpecificationsBrand Name:AutoleaderMaterial:Silicon NitrideOEM:82306BItem weight:11gFeaturesThis product is mainly made of silicon nitride ceramic substrate, with tungsten filament as the heat source, tungsten wire embedded in silicon nitride matrix, via hot-press sintering process to form an organic whole, then through grinding, welding wire, thus made the ignition components.Fitmentfor Webasto Air Top 2000Package Included1x Parking Heater Senser
L293D WiFi Smart Robot Car Motor Driver Expansion Board Dual High Power H Bridge Based on ESP12E
$9.79Expansion Board & ShieldAdd to cartL293D WiFi Smart Robot Car Motor Driver Expansion Board Dual High Power H Bridge Based On ESP12E For Specifications 1. Motor power (VM):4.5 ~ 36V 2. Control power (VIN):4.5V ~ 9V(10V MAX) 3. Provide the shortcut connector (short by VM and VIM), thus can use 4. May use common power source (4.5V~9V) by shorting VM …
220V 1000W Hot Plate Electric Iron Burner Heating Stove Heater Household Laboratory Heating Equipments
$52.64Laboratory Heating EquipmentsAdd to cartSpecificationsType:Electric Stove BurnerPlug Type:EUColor:WhiteVoltage:220VPower:1000WRegulating temperature:5 LevelsMaterial:Stainless Steel + IronSize:14*14*5CM (5.5*5.5*2in)Features– Adopted iron shell, thicken panel, material sturdy and durable to use– Portable single burner with 500 watts of power– Powered by electric, do not need fuel, eco-friendly– Easy-to-use temperature-setting knob for low, medium, or high heat– Provides quick and sustained heat; power indicator light– Single …
Reviews
There are no reviews yet.