5pcs 1 Channel 5v Relay Module High And Low Level Trigger
$13.57
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
Maximum load:AC 250V/10A, DC 30V/10A.
The chip optocoupler isolation, strong driving ability, stable performance, trigger current 5mA.
Working voltage:5V.
Every channel of the module can be set high or low level trigger by jumper.
Fault tolerant design, even if the control line is disconnect, the relay will not act.
Power indicator (green), 1 relay status indicator (red).
The interface design is humanized, all interfaces can be directly connected through the terminals, so it is very convenient.
Module size:50mm x 25mm x 18.5mm (length x width x height).
There are 4 fixed bolt holes, holes 3.1mm, spacing 67mm x 44.5mm.
Module interface
1, DC+:Connect the power positive pole.
2, DC-:Connect the power negative pole.
3, IN1:Can be controlled by high or low level.
Relay output:there is a 3 wire interface, all interfaces can be directly connected to lead to facilitate user use.
1, NO1:Relay normal open, the relay suspends before pulling in, and then short-connect with the COM.
2, COM1:Relay common interface
3, NC1:Relay normal close, short connected with COM before pulling inand suspended after pulling in.
High and low level trigger option
1. The 3-pin is the high level trigger selection.
2. When COM is short connected with LOW, the corresponding relay is LOW level trigger, while when COM is short connected with high end is high level trigger.
Package Included
5 x 1 Channel 5V Relay Module
Weight | 0.09 kg |
---|
Customers Also Viewed
M5Stack 8-Way Servo HAT STM32F030F4 Microcontroller Control Board for M5StickC ESP32 IoT Development Board
$16.96Other Module BoardAdd to cartDescription 8Servos HAT is an 8-way servo control board compatible with M5StickC. The brains of the borad is the STM32F030F4 microcontroller which communicates with M5StickC through I2C. In order to ensure that multiple servos can work at the same time, the HAT is equipped with a separate 16340 battery base for an external and independent …
Screw Shield V3 Terminal Expansion Board for UNO R3
$8.73Expansion Board & ShieldAdd to cartScrew Shield V3 Terminal Expansion Board For Compatible UNO R3DescriptionWe use to do work, always feel bad connection on the port. Either use bread plates into line, either using the sensor cable expansion board with Dupont, feel less reliable, and now we launch a terminal expansion board can be directly screwed onto the thread of …
Screw Shield V3 Terminal Expansion Board for UNO R3Read More
CH340G RS232 Upgrade USB to TTL Auto Converter Adapter STC Brush Module
$6.55Converter BoardAdd to cartFeaturesThere are power light PWR, and TXD and RXD indicatorsReserve RTS, CTS location3.3V and 5V dual voltage selectionSupport XP/WIN7/WIN8/WIN10 systemAnti-short-circuit, anti-overcurrent, anti-reverse, anti-high voltage multiple protection.Package includes1 x Module
10pcs CJMCU-8575 PCF8575 Bidirectional IIC I2C And SMBus I/O Expander Expansion Board
$80.46Expansion Board & ShieldAdd to cartDescriptionHave you run out of I/O pins This great IC allows the user to expand up to 16 I/O using only two I/O for control! The PCF8575C is controlled through an I2C interface and features 16-bits of quasi-bidirectional input/output pins.Package included10 x Module
5pcs 30MA 5V 0.15W Mini Solar Panel Epoxy Board
$16.04Smart Robot & Solar PanelAdd to cartSpecifications– Maximum power:0.15 (W)– Working current:0-30MA(Depending on the intensity of sunlight)– Working voltage:5 (V)– System voltage:5.5 (V)– Open circuit voltage:5.5 (V)– Short circuit current:0.05(A)– Dimensions:about 53*30 (mm)– Weight:about 12g– For:DIYer– Quantity:5PcsPackage Included5 x solar panel
20Pcs Keyes Brick Finger Heartbeat Module(Pad hole) with Pin Header Board Analog Signal
$55.28Sensor & Detector ModuleAdd to cartDescriptionThis module is fully compatible with ARDUINO single-chip microcomputer, and its connection port is also compatible with Arduino sensor expansion board. This module mainly includes infrared transmitter and photosensitive receiver. The infrared transmitter is on one side of the finger, and the photosensitive receiver is on the other side of the finger; the photosensitive receiver …
20Pcs Keyes Brick Finger Heartbeat Module(Pad hole) with Pin Header Board Analog SignalRead More
Reviews
There are no reviews yet.