BESTEP 6 Channel 12V Relay Module Low Level Trigger with Optocoupler Isolation
$14.34
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
Maximum load:AC 250V/10A, DC 30V/10A.
The chip optocoupler isolation, strong driving ability, stable performance, trigger current 5mA.
Working voltage is 12V.
Each channel of the module can be set up by high jumper or low level trigger.
Fault tolerant design, even if the control line is broken, the relay will not act.
Power indicator (green), 6 relay status indicator (red).
The interface design is humanized, all interfaces can be directly connected through the terminals, so it is very convenient.
Module size:142mm x 50mm x 18.5mm (length x width x height).
There are 4 fixed bolt holes, holes 3.1mm, spacing 67mm x 44.5mm.
Module interface
1. DC+:Connect the power positive pole
2. DC-:Connect the power negative pole.
3. IN1-IN6:According to the setting of each way, the corresponding relay-operating can be controlled by high or low level.
Relay output:there is a 18 wire interface, all interfaces can be directly connected to lead to facilitate user use.
1. NO1–NO6:Relay normal open, the relay suspends before pulling in, and then short-connect with the COM.
2. COM1–COM6:Relay common interface
3. NC1–NC6:Relay normal close, short connected with COM before pulling inand suspended after pulling in.
High and low level trigger option
1. S1-S6 is the high level trigger selection of relay 1 Channel – 6 Channel.
2. When COM is short connected with LOW, the corresponding relay is LOW level trigger, while when COM is short connected with high end is high level trigger.
Package Included
1 x 6 Channel 12V Relay Module
Weight | 0.08 kg |
---|
Customers Also Viewed
5pcs TS-300B Turbidity Sensor Detection Module Water Quality Tester Washing Machine Turbidity Transduce
$43.93Sensor & Detector ModuleAdd to cartPrincipleTurbidity sensor TS-300B measures the turbidity (counter of suspended matter) in the wash water. Based on the optical principle, the sensor uses the light-emitting diode and phototransistor to receive the specific wavelength to measure the opacity or other substances of dirty water. concentration. By using phototransistors and light-emitting diodes, the light emitted by the sensor …
3Pcs USB Fan Speed Controller Module Reducing Noise Multi-stall Adjustment Governor DC 4-12V
$20.74Motor PWM Speed ControllerAdd to cartFeatures– USB Fan Air Conditioner – Strong winds and weak wind adjust freely – Stepless Speed Regulation – Suitable for the very common 5.0V USB fan on the market Regulation PrincipleThe non-adjustable fan is a 5V direct fan motor,while the two-stall fan is the interior has a step-up circuit board,when placed in the second gear,the …
5pcs JDY-08 BLE bluetooth 4.0 Serial Port Wireless Module Low Power Master-slave Support Airsync i Beacon
$45.12Smart ModuleAdd to cartFeaturesJDY-08 transparent transmission module is based on bluetooth 4.0 protocol standard, working frequency range is 2.4GHZ range, modulation mode is GFSK, large transmission power is 0db, large transmission distance is 80 meters, TICC2541 chip design is adopted, and users can modify device name by AT command. , service UUID, transmit power, pairing password and other …
ADC Module ADS1100 for Analog Signal Capture Converter Compatible M5StickC ESP32 Mini IoT Development Board Fi
$14.74Converter BoardAdd to cartnull Description ADC_HAT is another type of C-HAT specifically design for M5StickC controller. Same as ADC unit, this is an ADC converter component for stickc. Packed with an ADC converter chip ADS1100, which is a fully differential, 16-bit, self-calibrating, A/D converter. Extremely easy to design with and configure, the ADS1100 allows you to obtain precise …
5pcs Mini MP1584EN DC-DC BUCK Adjustable Step Down Module 4.5V-28V input 0.8V-20V Output
$8.94Power Supply ModuleAdd to cartSpecificationsModel:MP1584Name:DC-DC step-down moduleInput Voltage:4.5V ~ 28VOutput voltage:0.8V ~ 20VOutput Current:3A (Max)Conversion efficiency:96% (maximum)Output RippleSwitching frequency:1.5MHz (highest) typically 1MHzOperating Temperature:-45°C ~ +85°CSize:22mm * 17mm (L * W )Application areas:DIY mobile power, monitor power supply, power buggies, camera power supply, car power, communications equipment supply,etc.Packge included5 x Step Down Module
LILYGO TTGO T-Koala ESP32 WiFi and bluetooth Module 4MB Development Board Based on ESP32-WROOM-32 Micro USB
$26.23Smart ModuleAdd to cartFeatureEspressif official ESP32-WROOM-32 moduleLatest ESP32 version:REV14MB FLASHLithium battery interface, 500mA maximum charging currentCompatible with , MicroPythonDefault firmware:latest MicroPythoTechnical specificationsMicrocontroller:ESP-32Board power supply:(USB) 5VSupport battery:Lipo Battery 3.7VWorking voltage:3.3VFlash:4 MbytesLength:78 mmWidth:27 mmWeight:7.8 gramsPackage includes1 x ESP32 WiFi&bluetooth Broad2 x Pin
Reviews
There are no reviews yet.