DIY Airband Radio Receiver Aviation Band Receiver Kit
$43.73
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Description
Like many scanner enthusiasts and ham operators, you are interested in listening in on all the excitement manifest in aeronautic communication, but lack the equipment to pursue your interest, then maybe the Aviation-Band Receiver described in this article is for you.
The Aviation Receiver, designed to tune the 118-135MHz band, features exceptional sensitivity, image rejection, signal-to-noise ratio, and stability.
The receiver is ideally suited to listening in on ground and air communication associated with commercial airlines and general aviation.
Powered from a 9-volt alkaline battery, it can be taken along with your to local airports so that you won’t miss a moment of the action.
And even if you’re nowhere near an airport, this little receiver will pick-up all the ground-to-air and vice-versa communications of any plane or ground facility within about 130 miles (190Km).
Color:Green
Material:CCL
Construction
Once you have obtained all of the components and the board for the Aviation Receiver, construction can begin. A parts-placement diagram is shown in Fig. When assembling the project, take special care that polarity-sensitive components (electrolytic capacitors [keep leads as short as possible], diodes, and transistors) are installed properly. Just one part installed backwards can cause grievous harm!
Inductors (Aircoils) L1,L3,L5 can be made easily on a 5mm drill bit. Before you wind them, scrape the enamel of each end, about 5mm. Then wind the 1.5 turn (2-turns is okay too). I know it can be tricky especially if you have big fingers like me. Begin by installing the passive components (6 jumper wires, sockets, resistors, capacitors, inductors). Followed by installing the active components; diodes, transistors, and IC’s. Once the active components have been installed, check your work for the usual construction errors; cold solder joints, misplaced or reversed-lead components, solder bridges, etc. Once you have determined that he circuit has been correctly assembled, it’s time to consider the enclosure that will house the receiver.
The receiver’s circuit board can be housed in any enclosure that you choose.
Note
Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
Package included
1 x DIY KITs Airband Radio Receiver Aviation Band Receiver
1 x English manual
Weight | 0.081 kg |
---|
Customers Also Viewed
5pcs Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology Small Production Kit
$16.60DIY Electronic KitsAdd to cartDescriptionThe purpose of the experiment1. Understand and recognize the light-emitting diodes and illuminate the light-emitting diodes (LEDs);2. Understand the role of understanding resistance, series and parallel resistance;3. Understand the self-locking switch;4. Understand and recognize adjustable resistors and use adjustable resistors;Experimental stepsStep 1:The long leg of the light-emitting diode (LED) is the positive pole, and the …
50pcs Universal PCB Board 7x9cm 2.54mm Hole Pitch DIY Prototype Paper Printed Circuit Board Panel Single Sided Board
$32.93Electronic Accessories & SuppliesAdd to cartFeaturesPremium one side prototype PCB printed circuit board, universal strip breadboard.All holes are plated through, smooth and clear.Sturdy and easy to use, the plated holes are very solid which makes it very easy to solder components on and they can hold up well and handle reasonable heat levels and dwell times.A good assortment of quality …
50mm Submersible Bore 0.5 HP Water Farm Garden Deep Well Pump 220V 180ft 8GPM
$340.19Electrical Pump & ValveAdd to cartFeatures-2inch deep well submersible pump, fits in the 2inch well casing.-Patented impeller design provides extended pump life and heavy flow under the severe circumstances.-This pump has a much longer pump life than the all-plastic-bottom-suction pump.-Solid 304 stainless steel body with heavy duty cast iron discharge.-Industrial grade heavy duty, also good for home usage.-Built in 1/2 …
50mm Submersible Bore 0.5 HP Water Farm Garden Deep Well Pump 220V 180ft 8GPMRead More
1Hz-150Khz 3.3V-30V Signal Generator PWM Pulse Frequency Duty Cycle Adjustable Module LCD Display
$22.06Other Module BoardAdd to cartParameter settingsThe module has four independent keys, used to set the frequency and duty cycle, support short press (increase or decrease a unit)and long press (fast increase or decrease), very simple, set the parameters automatically save, power failure Lost.Module parameters1. Working voltage:3.3 ~ 30V;2. Frequency range:1Hz ~ 150KHz;3. Frequency accuracy:the accuracy in each range is …
5pcs LCD1602 LCD Shell for 1602 Blue/Yellow And I2C 1602 Blue/Yellow Green Backlight LCD Module Case
$17.73Electronic Accessories & SuppliesAdd to cartDescription Screen size:2.5 inches Material:acrylic Application 1602 Blue Backlight LCD Display Module:https://www.hobbyant.com/1Pc-1602-Character-LCD-Display-Module-Blue-Backlight-p-978160.htmlrmmds=search 1602 Yellow Backlight LCD Display Module:https://www.hobbyant.com/1Pc-1602-Character-LCD-Display-Module-Yellow-Backlight-For–p-978155.htmlrmmds=search I2C 1602 Blue Backlight LCD Display Module:https://www.hobbyant.com/IIC-I2C-1602-Blue-Backlight-LCD-Display-Module-For–p-950726.htmlrmmds=search I2C 1602 Yellow Green Backlight LCD Display Module:https://www.hobbyant.com/IICI2C-1602-Yellow-Green-Backlight-LCD-Display-Module-For–p-950728.htmlrmmds=search Package included 5 x LCD1602 LCD shell
Reviews
There are no reviews yet.